Research into the use of marble waste as mineral filler in soil pigment-based paints and as an active pigment in waterborne paints
Source abstract
Abstract
Abstract Producing paint using waste and soil is an efficient way of contributing to sustainable development and reducing costs in the finishing and protection of buildings. Although there are numerous studies related to paints of natural land base, there remain certain technical limitations to be overcome. Moreover, no research has been found in the literature on the use of marble waste as an active or inert pigment in the production of paint, although this waste has several pertinent properties and basic constituents. Thus, the aim of this study was to evaluate whether the use of untreated marble waste as an active pigment in building paint enables a product to be developed which meets specifications and whether the performance of soil pigment-based paints can be improved by incorporating marble waste as a mineral filler. The only preparation for using the waste and the soils as pigments was to sieve them to remove coarser impurities. The samples were formulated based on mix planning using the simplex network and consisted of: marble waste pigment (MWP), soil pigment (SP) and polyvinyl acetate resin (PVA). The amount of water varied according to the ideal viscosity range for paint application. The formulas were analyzed for hiding power (HP), abrasion resistance (AR), microbiological attack and resistance to weathering. The results showed that, for paints produced with MWP as the only pigment, the performance set out in ABNT NBR 15079:2011 was achieved above a percentage of 30% resin in solution. Furthermore, the addition of MWP to SP-based paints provided a film with higher HP and, together with the increased resin content, increased the AR of the samples. Five formulas met both HP and AR performance specifications. The percentages in the mixture were as follows: 0.3 PVA and 0.7 MWP; and 0.4 PVA and 0.6 MWP, with MWP as the sole pigment; 0.25 PVA, 0.175 YSP (yellow soil pigment) and 0.575 MWP; and 0.35 PVA, 0.175 YSP and 0.475 MWP, of YSP and MWP; and 0.25 PVA, 0.175 RSP (red soil pigment) and 0.575 MWP, of RSP and MWP. The weatherability test showed that MWP addition to the paint formula contributed to increased paint durability and improved photolytic stability. Thus, the results indicate that marble waste, as an active pigment or mineral filler, is a promising alternative for producing building paint.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Building materials and conservation
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (77)
Show source-provided references
1. Recycling of marble waste: a review based on strength of concrete containing marble waste10.1016/j.jenvman.2018.10.034 ↗
2. Brazilian Association of the Ornamental Stones Industry-ABIROCHAS, The Brazilian Sector of Ornamental Stones, 2018. http://abirochas.com.br/wp-content/uploads/2018/06/abinoticias/Setor_de_Rochas_Ornamentais.pdf (accessed 18.12.26) (In Portuguese).
3. Resource efficiency impact on marble waste recycling towards sustainable green construction materials10.1016/j.cogsc.2018.06.005 ↗
4. B. Demirel, K.E. Alyamaç, Waste marble powder/dust, In: Waste and Supplementary Cementitious Materials in Concrete, 2018, pp. 181–197.10.1016/B978-0-08-102156-9.00006-7 ↗
5. Recycling of dimensional stone waste in concrete: a review10.1016/j.jclepro.2016.06.126 ↗
6. The use of the powder marble by-product to enhance the properties of brick ceramic10.1016/j.conbuildmat.2006.05.029 ↗
7. A. Awol, Using marble waste powder in cement and concrete production (Unpublished. MSc Thesis), Addis Ababa University, Ethiopia, 2011.
8. Use of waste marble aggregates in concrete10.1016/j.conbuildmat.2010.09.037 ↗
9. Properties of concrete paving blocks made with waste marble10.1016/j.jclepro.2011.08.023 ↗
10. Investigation on the usage of waste marble powder in cement-based adhesive mortar10.1016/j.conbuildmat.2017.08.014 ↗
11. Composite utilizing residues of marble and granite for building popular homes10.1016/j.jobe.2017.01.003 ↗
12. Recovery and formation mechanism of high brightness calcite powders from marble waste by the alkaline hydrothermal treatment
13. Application of statistical analysis to evaluate the corrosion resistance of steel rebars embedded in concrete with marble and granite waste dust10.1016/j.jclepro.2018.11.091 ↗
14. Effect of quantity and size distribution of calcite filler on the quality of water borne paints10.1016/j.porgcoat.2012.02.002 ↗
15. Preparation and modification of nano calcium carbonate filler from waste marble dust and commercial limestone for papermaking wet end application10.1016/j.powtec.2015.04.006 ↗
16. Precipitated calcium carbonate production, synthesis and properties
17. Fazenda · 2009
18. Sustainability index development for manufacturing industry10.1016/j.seta.2017.01.010 ↗
19. A review of current and future challenges in paints and coatings chemistry
20. Utilization and value addition of copper tailing as an extender for development of paints10.1016/j.jhazmat.2005.05.052 ↗
21. The preparation of magnetite, goethite, hematite and maghemite of pigment quality from mill scale iron waste10.1016/j.dyepig.2006.01.038 ↗
22. Novel anticorrosive pigments based on waste material for corrosion protection of reinforced concrete steel10.1016/j.conbuildmat.2015.08.111 ↗
23. Reuse of iron ore tailings from tailings dams as pigment for sustainable paints10.1016/j.jclepro.2018.07.313 ↗
24. Influence of the incorporation of granite waste on the hiding power and abrasion resistance of soil pigment-based paints10.1016/j.conbuildmat.2019.02.046 ↗
25. Cornell · 2003
26. Production process and evaluation of performance requirements of soil pigments based paint for buildings
27. da Silva · 2014
28. Pigments for pain
29. Brazilian Association of Technical Norms, NBR 7181 – Soil – Grain size analysis, Rio de Janeiro, Brazil, 2016 (In Portuguese).
30. Embrapa, Guide of Soil Analysis Methods, Rio de Janeiro, Brazil, 1997 (In Portuguese).
31. Jackson · 1982
32. 1999
33. Greiner · 2004
34. Silva · 2005
35. Formulation effects on the distribution of pigment particles in paints10.1016/S0300-9440(03)00095-X ↗
36. Brazilian Association of Technical Norms, NBR 5849 – Paints – Determination of viscosity by Ford glass, Rio de Janeiro, Brazil, 2015 (In Portuguese).
37. American Society for Testing and Materials American Society for Testing and Materials, ASTM D 3723-05 - Standard Test Method for Pigment Content of Water-Emulsion Paints by Low-Temperature Ashing, ASTM International, West Conshohocken, PA, 2011
38. Brazilian Association of Technical Norms, NBR 15079 – Paints for Buildings – Specification of Paints Performance for Non Industrial Buildings – Light Colours Latex Paints, Rio de Janeiro, Brazil, 2011 (In Portuguese).
39. Brazilian Association of Technical Norms, NBR 14942 – Paints for Buildings – Method for Performance Evaluation of Paints for Non Industrial Buildings – Determination of Dry Paint Film Hiding Power, Rio de Janeiro, Brazil, 2016 (In Portuguese).
40. American Society for Testing and Materials, ASTM D2805-11 - Standard Test Method for Hiding Power of Paints by Reflectometry, ASTM International, West Conshohocken, PA, 2018.
41. ISO 6504-3 – Paints and Varnishes – Determination of Hiding Power – Part 3: Determination of Contrast Ratio of Light-coloured Paints at a Fixed Spreading Rate, 2006.
42. Brazilian Association of Technical Norms, NBR 15078 – Paints for Buildings – Method for Performance Evaluation of Paints for Non Industrial Buildings – Determination of Wet Abrasion Resistance Without Abrasive Paste, Rio de Janeiro, Brazil, 2006 (In Portuguese).
43. American Society for Testing and Materials, ASTM D4060-14 - Standard Test Method for Abrasion Resistance of Organic Coatings by the Taber Abraser, ASTM International, West Conshohocken, PA, 2014.
44. ISO 7784-3 – Paints and Varnishes – Determination of Resistance to Abrasion – Part 3: Method with Abrasive-paper Covered Wheel and Linearly Reciprocating Test Specimen, 2016.
45. Simultaneous optimization of several response variables10.1080/00224065.1980.11980968 ↗
46. Selective media for isolation of Agrobacterium, Corynebacterium, Erwinia, Pseudomonas and Xanthomonas
47. A. C. Alfenas, R. G. Mafia. Methods in Phytopathology. Viçosa, Brazil: Editors UFV, 2016. (In Portuguese).
48. American Society for Testing and Materials, ASTM G7 - Standard Practice for Atmospheric Environmental Exposure Testing of Nonmetallic Materials, ASTM International, West Conshohocken, PA, 2013.
49. ISO 2810 - Paints and varnishes – Natural weathering of coatings – Exposure and assessment, 2004.
50. UFV, Federal University of Viçosa, Department of Agricultural Engineering, Main Climatological Station of Viçosa, Weather Report 2018, Viçosa, 2018 http://www.posmet.ufv.br/wp-content/uploads/2019/09/Esta%C3%A7%C3%A3o-Autom%C3%A1tica-2018.pdf (accessed 18.12.17) (In Portuguese).
51. UFV, Federal University of Viçosa, Department of Agricultural Engineering, Main Climatological Station of Viçosa, Weather Report 2019, Viçosa, 2018. http://www.posmet.ufv.br/wp-content/uploads/2019/11/Esta%C3%A7%C3%A3o-Autom%C3%A1tica-2019.pdf (accessed 19.11.12) (In Portuguese).
52. COLORMINE, Delta-E Calculator, ColorMine.org, 2018. http://colormine.org/delta-e-calculator (accessed 18.12.15).
53. Oates · 2008
54. Calcium carbonate nanocomposites
55. Effect of precipitated calcium carbonate additions on waterborne paints at different pigment volume concentrations10.1016/j.porgcoat.2015.02.003 ↗
56. The physical chemistry of dispersion
57. Coatings for buildings
58. Mixtures of fine-grained minerals–kaolinite and carbonate grains10.1346/CCMN.2008.0560601 ↗
59. Appearance qualities of paint – basic concepts
60. Application of spherical hollow calcium carbonate particles as filler and coating pigment
61. Role of marble microstructure in near-infrared laser-induced damage during laser cleaning10.1063/1.1649811 ↗
62. Potentials of Nigerian calcined kaolin as paint pigment
63. Emulsion polymerization: effects of polymerization variables on the properties of vinyl acetate based emulsion polymers
64. A new method for measurement of particle abrasivity10.1016/S0043-1648(01)00666-4 ↗
65. Molecular view of polymer/water interfaces in latex paint10.1021/ma500866f ↗
66. F. Karakas, B. V. Hassas, K. Özhan, F. Boylu, M. S. Celik, Calcined kaolin and calcite as a pigment and substitute for tio2 in water based paints. In: XIV Balkan Mineral Processing Congress, 2011, 461–464.
67. Stabilization mechanism of main paint pigments10.1016/j.porgcoat.2018.07.019 ↗
68. Novel PMMA/CaCO3 nanocomposites abrasion resistant prepared by an in situ polymerization process10.1021/nl015518v ↗
69. Presence and effects of anaerobic bacteria in water-based pains
70. Collaborative investigations of laboratory test methods for evaluation of the growth of pink yeasts on paint films
71. Microbial evaluation and deterioration of paints and paint-products
72. Forms of polymer degradation: overview
73. Photocatalytic paint for fungi growth control under different environmental conditions and irradiation sources10.1016/j.jphotochem.2018.05.034 ↗
74. Effect of wollastonite extender on the properties of exterior acrylic paints10.1016/j.porgcoat.2015.12.014 ↗
75. G. Buxbaum, G. Pfaff (Ed.), Industrial Inorganic Pigments, third ed., WileyVCH, Weinheim, 2008.
76. Poly (vinyl acetate) paints in works of art: a photochemical approach. Part 110.1016/j.polymdegradstab.2010.01.015 ↗
77. Preparation and characterization of calcium carbonate–titanium dioxide core–shell (CaCO3@ TiO2) nanoparticles and application in the papermaking industry10.1016/j.powtec.2015.05.039 ↗