journal article·2021-01

Animal fibers as water reservoirs for internal curing of mortars and their limits caused by fiber clustering

F.C. Antico, P. Rojas, F. Briones, G. Araya-Letelier

Publisher page

Abstract

Abstract We present a bottom-up experimental research to address evidence of internal curing of mortars using randomly distributed pig-hair as water reservoirs. Plain and reinforced mortars with pig hair ranging from 0 to 8 kg of fibers per cubic meter of mortar were prepared. The microstructures of plain and reinforced mortars were scanned using electron microscopy and the microhardnesses were measured within the bulk cement paste and cement paste near pig fibers. Electrical resistivity, surface absorption, and residual compressive strength of mortars after freeze-thaw cycles were used to test the effects of internal curing caused by pig hair. Natural fibers used to reinforce mortars increase their toughness and provide part of the necessary water for internal curing, yet internal curing originated by the addition of natural fibers is not proportional to fiber dosage; where the potential to form fiber clusters increases as fiber dosage increases. Results show that there is an optimum fiber dosage that maximizes internal curing caused by these fibers. This study contributes to the research on reinforced mortars with natural fibers to provide sustainable solutions for construction materials.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Innovative concrete reinforcement materials · Concrete Properties and Behavior · Concrete and Cement Materials Research

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (44)

Show source-provided references
1. Effectiveness of new natural fibers on damage-mechanical performance of mortar10.1016/j.conbuildmat.2017.07.072 ↗
2. Impact strength of a few natural fibre reinforced cement mortar slabs: a comparative study10.1016/j.cemconcomp.2004.09.006 ↗
3. Cementitious building materials reinforced with vegetable fibres: A review10.1016/j.conbuildmat.2010.07.024 ↗
4. Lightweight construction materials: Mortar reinforced with date-palm mesh fibres10.1016/j.tafmec.2018.12.011 ↗
5. Influence of natural fiber dosage and length on adobe mixes damage-mechanical behavior10.1016/j.conbuildmat.2018.04.151 ↗
6. The influence of date palm mesh fibre reinforcement on flexural and fracture behaviour of a cement-based mortar10.1016/j.compositesb.2018.07.017 ↗
7. Pork and swine industry and trade summary
8. Iberwaste, “Disposal and valorization of Iberian pig wastes from slaughterhouses,” LIFE11 ENV/ES/000562, 2015
9. Steel, aluminium and carbon: alternative strategies for meeting the 2050 carbon emission targets
10. Mindess · 2002
11. R. K. Pachauri and L. A. Meyer, “IPCC, 2014: Climate Change 2014: Synthesis Report. Contribution of Working Groups I, II and III to the Fifth Assessment Report of the Intergovernmental Panel on Climate Change,” 2014.
12. Cement and carbon emissions10.1617/s11527-013-0114-5 ↗
13. J. I. Daniel, S. H. Ahmad, M. Arockiasamy, and H. P. et al Ball, “State-of-the-art report on fiber reinforced concrete Reported by ACI Committee 544,” Farmington Hills, MI, 2002.
14. D. P. Bentz and W. J. Weiss, Internal Curing: A 2010 State-of-the-Art Review, 2011.10.6028/NIST.IR.7765 ↗
15. Internal curing and microstructure of high-performance mortars
16. Release of internal curing water from lightweight aggregates in cement paste investigated by neutron and X-ray tomography10.1016/j.nima.2011.02.012 ↗
17. An overview on the effect of internal curing on shrinkage of high performance cement-based materials10.1016/j.conbuildmat.2017.04.154 ↗
18. Lechugilla natural fiber as internal curing agent in self compacting concrete (SCC): Mechanical properties, shrinkage and durability
19. Fiber-reinforced mortar incorporating pig hair10.4028/www.scientific.net/AEF.21.219 ↗
20. Hydro-abrasive erosion of high performance fiber-reinforced concrete10.1016/j.wear.2008.11.010 ↗
21. Influence of polypropylene fiber geometry on plastic shrinkage cracking in concrete10.1016/j.cemconres.2006.01.010 ↗
22. Fatigue Strength of Polypropylene Fiber Reinforced Concretes
23. ASTM International, “ASTM C595/C595M-16. Standard Specification for Blended Hydraulic Cements,” 2016.
24. ASTM International, “Standard specification for concrete aggregates; ASTM C33 / C33M-16e1; ASTM International: West Conshohocken, PA, USA,” 2016.
25. Determining the Moisture Content of Pre-Wetted Lightweight Aggregate : Assessing the Variability of the Paper Towel and Centrifuge Methods
26. ASTM C348 standard test method for flexural strength of hydraulic-cement mortars
27. ASTM C349-97. Standard test method for compressive strength of hydraulic-cement mortars (using portions of prisms broken in flexure)
28. Microhardness testing of cementitious materials10.1016/S1065-7355(96)90051-6 ↗
29. Protected paste volume in concrete: Extension to internal curing using saturated lightweight fine aggregate10.1016/S0008-8846(99)00178-7 ↗
30. Effect of elevated temperature on meso- and micro-structure and compressive strength of high-strength concrete and mortar containing blast-furnace slag10.3151/jact.16.498 ↗
31. UNE-EN 1015-10 Métodos de ensayo de los morteros para albañilería. Parte 10: Determinación de la densidad aparente en seco del mortero endurecido,. AENOR, 2000
32. J. Castro, R. Spragg, and P. Kompare, Portland Cement Concrete Pavement Permeability Performance. 2010.10.5703/1288284314244 ↗
33. American Association of State Highway and Transportation Official, “AASHTO T 358-15 Standard Method of Test for Surface Resistivity Indication of Concrete’s Ability to Resist Chloride Ion Penetration,” 2015.
34. J. Schlitter, R. Henkensiefken, J. Castro, K. Raoufi, and W. J. Weiss, “Development of internally cured concrete for increased service life,” no. October, 2010.10.5703/1288284314262 ↗
35. Mechanical-damage behavior of mortars reinforced with recycled polypropylene fibers10.3390/su11082200 ↗
36. Experimental mechanical-damage assessment of earthen mixes reinforced with micro polypropylene fibers10.1016/j.conbuildmat.2018.11.261 ↗
37. Effect of nano-SiO2 particles and curing time on development of fiber-matrix bond properties and microstructure of ultra-high strength concrete10.1016/j.cemconres.2017.02.031 ↗
38. A study of mechanical properties of autoclaved calcium silicate systems10.1016/0008-8846(75)90069-1 ↗
39. Specimen preparation for scanning electron microscopy
40. “ImageJ.” [Online]. Available: https://imagej.nih.gov/ij/index.html. [Accessed: 08-Oct-2019].
41. Investigation of freeze–thaw effects on mechanical properties of fiber reinforced cement mortars10.1016/j.compositesb.2013.11.013 ↗
42. Frost resistance of polyvinyl alcohol fiber and polypropylene fiber reinforced cementitious composites under freeze thaw cycling10.1016/j.compositesb.2015.12.009 ↗
43. A review on the use of LWA as an internal curing agent of high performance cement-based materials10.1016/j.conbuildmat.2019.05.126 ↗
44. Investigation of internal curing effects on microstructure and permeability of interface transition zones in cement mortar with SEM imaging, transport simulation and hydration modeling techniques10.1016/j.conbuildmat.2014.12.014 ↗