Evaluating the flexural behavior of green copper slag-contained steel fiber reinforced SCC beams with/without initial notches
Source abstract
Abstract
Nature-friendly concrete composites containing hooked-end steel fibers (SF) and copper slag (CS) aggregates can play important roles in sustainable construction, preventing the nature destruction, reducing brittle fracture and improving formability of concrete elements. To this end, effects of SF (0.1, 0.3, and 0.5%) and CS (20, 30, 40, 50 and 60%) on the compressive strength and microstructure of concrete composites were examined and the flexural behavior and toughness of beams with/without notches were evaluated and compared with the control design (no SF/CS) using Post Crack Strength (PCS), CECS 13, ASTM C1018, JSCE-SF4, ASTM C1609 and JG/T 472 models. Same laboratory setup and specimen dimension were used for accurate evaluations and results showed that CS aggregates improved the properties of fresh concrete and its workability was reduced by high SF volumes. Increasing the latter from 0.1 to 0.5% increased the optimal CS from 20 to 50% to achieve better compressive strength, and increasing the CS volume up to 30% strengthened the microstructure of SF-reinforced composites. Compared with notched (N) specimens, unnotched (UN) ones had higher peak loads and lower flexural strengths. At the lowest fiber volume, CS effects on both flexural behavior and fracture toughness were greater, and JG/T 472 method calculated the flexural toughness better than the other mentioned methods because of separating the pre- and post-peak load areas in the load–displacement curve and also using the flexural strength (which is affected by peak load).
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Innovative concrete reinforcement materials · Structural Behavior of Reinforced Concrete · Concrete and Cement Materials Research
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (100+)
Show source-provided references
1. Flexural toughness evaluation of basalt fibre reinforced HPC beams with and without initial notch
2. Fresh properties of self-compacting concrete containing ground waste glass micro-particles as cementing material10.3151/jact.13.50 ↗
3. Utilization of waste glass micro-particles in producing self-consolidating concrete mixtures10.1007/s40069-016-0141-z ↗
4. Effect of copper slag on the resistance characteristics of SCC exposed to the acidic environment10.1007/s42107-019-00218-x ↗
5. Influence of different curing conditions and water to cement ratio on properties of self-compacting concretes10.1016/j.conbuildmat.2019.117570 ↗
6. The effect of NiTi shape memory alloy, polypropylene and steel fibres on the fresh and mechanical properties of self-compacting concrete10.1016/j.conbuildmat.2019.04.207 ↗
7. Mode I fracture toughness of fibre reinforced concrete10.1016/j.tafmec.2017.03.015 ↗
8. Utilization of micro copper slag in SCC subjected to high temperature
9. The propagation speed of multiple dynamic cracks in fiber-reinforced cement-based composites measured using DIC10.1016/j.cemconcomp.2021.104140 ↗
10. I. Markovic. 2006. High-performance Hybrid-fibre Concrete: Development and Utilisation, PhD thesis, Delft University of Technology, The Netherlands.
11. Combining Kriging meta models with U-function and K-Means clustering for prediction of fracture energy of concrete
12. Fibre reinforced cement-based (FRC) composites after over 40 years of development in building and civil engineering10.1016/j.compstruct.2008.03.006 ↗
13. Strength and fracture energy characteristics of self-consolidating concrete incorporating polyvinyl alcohol, steel and hybrid fibres10.1016/j.conbuildmat.2013.03.054 ↗
14. Use of steel fibers to optimize self-consolidating concrete mixtures containing crumb rubber
15. Influence of steel fibres on strength and ductility of normal and lightweight high strength concrete10.1016/S0360-1323(01)00109-3 ↗
16. Properties of self-consolidating rubberised concrete reinforced with synthetic fibres10.1680/jmacr.16.00433 ↗
17. Toughness enhancement in steel fiber reinforced concrete through fiber hybridization10.1016/j.cemconres.2007.05.005 ↗
18. Evaluation of the mechanical behavior of pumice lightweight concrete reinforced with steel and polypropylene fibers10.1016/j.conbuildmat.2018.11.109 ↗
19. Studying the fracture parameters and size effect of steel fiberreinforced self-compacting concrete10.1016/j.conbuildmat.2018.12.172 ↗
20. Sustainable cleaner production of concrete with high volume copper slag10.1016/j.jclepro.2018.04.245 ↗
21. Effect of waste glass and curing aging on fracture toughness of self-compacting mortars using ENDB specimen10.1016/j.conbuildmat.2021.122711 ↗
22. The composition and environmental hazard of copper slags in the context of the basel convention10.1016/j.resconrec.2004.05.005 ↗
23. Ground copper slag as a supplementary cementing material and its influence on the fresh properties of self-consolidating concrete. IES
24. Use of Copper Slag Microparticles in Self-Consolidating Concrete
25. Durability characteristics of self-compacting concrete made with copper slag10.1016/j.conbuildmat.2020.118580 ↗
26. Mechanical properties of high-strength concrete incorporating copper slag as coarse aggregate10.1016/j.conbuildmat.2008.12.005 ↗
27. Characteristics and utilization of copper slag - a review10.1016/S0921-3449(02)00171-4 ↗
28. Effect of copper slag as a fine aggregate on the properties of cement mortars and concrete10.1016/j.conbuildmat.2010.06.090 ↗
29. Sustainable use of copper slag in self compacting concrete containing supplementary cementitious materials10.1016/j.jclepro.2017.03.031 ↗
30. Utilization of copper slag in cement and concrete10.1016/j.resconrec.2008.06.008 ↗
31. Mechanical performance and post-cracking behavior of self-compacting steel-fber reinforced eco-effcient ultra-high performance concrete10.1016/j.cemconcomp.2021.104050 ↗
32. Mechanical properties, durability and environmental evaluation of rubberized concrete incorporating steel fiber and metakaolin at elevated temperatures10.1016/j.jclepro.2020.120126 ↗
33. Copper slag as sand replacement for high performance concrete10.1016/j.cemconcomp.2009.04.007 ↗
34. Environmental protection by using waste copper slag as a coarse aggregate in self-compacting concrete10.1016/j.jenvman.2020.111013 ↗
35. Strength and micro-structural properties of self-compacting concrete incorporating copper slag10.1016/j.conbuildmat.2019.07.105 ↗
36. CECS 13. 2009. Standard test methods for fiber reinforced concrete. China Construction Engineering Association, China planning press, Beijing.
37. Test Method for Flexural Toughness and First-Crack Strength of Fibre-Reinforced Concrete (Using Beam with Third-Point Loading). ASTM
38. Steel Fiber Reinforced Concrete Research Subcommittee
39. Standard Test Method for Flexural Performance of Fiber-Reinforced Concrete (Using Beam with Third-point Loading), ASTM
40. CS (Chinese Standard) JG/T 472, 2015. Steel Fiber Reinforced Concrete, Ministry of Housing and Urban-Rural Development People’s Republic China (MOHURD).
41. Investigating the mechanical and hydraulic characteristics of pervious concrete containing copper slag as coarse aggregate10.1016/j.conbuildmat.2018.11.230 ↗
42. Optimum content of copper slag as a fne aggregate in high strength concrete10.1016/j.matdes.2009.12.037 ↗
43. Producing green Roller Compacted Concrete (RCC) using fine copper slag aggregates10.1016/j.jclepro.2022.133005 ↗
44. Siddique, R., Singh, M., Jain, M. Recycling copper slag in steel fibre concrete for sustainable construction. J. Clean. Prod. 271, 122559.10.1016/j.jclepro.2020.122559 ↗
45. The cracked Brazilian specimen for fracture toughness testing of concrete10.1007/BF00017975 ↗
46. Graybeal · 2012 · 395
47. Report on Indirect Method to Obtain Stress-Strain Response of Fiber Reinforced Concrete (FRC)
48. Final Recommendation of RILEM TC 162-TDF: Test and Design Methods for Steel Fibre Reinforced Concrete: r-e Design Method10.1617/14007 ↗
49. DIN EN 14561, 2006. Chemical Disinfectants and Antiseptics – Quantitative Carrier Test for the Evaluation of Bactericidal Activity for Instruments Used in the Medical Area – Test Method and Requirements (Phase 2, Step 2).
50. Fib · 2013
51. Astm c293, · 2016
52. JCI SF4, 1983. Standard Test Method for Flexural Strength and Flexural Toughness of Fiber Reinforced Concrete.10.1520/CCA10229J ↗
53. Nbn, b., · 1992
54. German guidelines on steel fiber concrete
55. ASTM C1399, 2015. Standard Test Method for Obtaining Average Residual-Strength of Fiber-Reinforced Concrete, ASTM International.
56. Fracture properties of steel fiber reinforced high strength concrete using work of fracture and size effect methods10.1016/j.conbuildmat.2017.03.089 ↗
57. Investigating the effects of maximum aggregate size on selfcompacting steel fiber reinforced concrete fracture parameters10.1016/j.conbuildmat.2017.11.141 ↗
58. Test for crack opening displacement of steel fiber reinforced concrete under Three-Point Bending10.4028/www.scientific.net/AMM.36.157 ↗
59. Relationship between deflection and crack mouth opening displacement of self-compacting concrete beams with and without fibers10.1080/15376494.2014.906689 ↗
60. Experimental and numerical study of flexural properties in UHPFRC beams with and without an initial notch10.1016/j.conbuildmat.2020.121196 ↗
61. Significance of Tests and Properties of Concrete and Concrete-Making Materials
62. Effects of curing temperature and early freezing on the pull-out behavior of steel fibers10.1016/0008-8846(89)90029-X ↗
63. Flexural response of hybrid fiber reinforced cementitious composites
64. Hybrid fiber reinforced concrete: fiber synergy in high strength matrices, RILEM10.1617/14095 ↗
65. Investigation on flexural toughness evaluation method of steel fiber reinforced lightweight aggregate concrete10.1016/j.conbuildmat.2016.11.101 ↗
66. Flexural Behavior of Polyvinyl Alcohol Fiber-Reinforced Ferrocement Cementitious Composite10.1061/(ASCE)MT.1943-5533.0003565 ↗
67. Astm c150, · 2009
68. Astm c 33, · 2008
69. Astm c494, · 2010
70. Standard Specification for Ready – Mixed Concrete. ASTM
71. EFNARC, February 2002. Best Practices Guidelines for Self-Consolidating Concrete, Prepared by Ready Mixed Concrete Association of Ontario.
72. Efnarc · 2005
73. Astm c 39, · 2009
74. Standard Test Method for Flexural Strength of Concrete (Using Simple Beam with Center-Point Loading). ASTM
75. Determination of the fracture energy of mortar and concrete by means of three-point bend tests on notched beams10.1007/BF02472918 ↗
76. Use of polymeric fibers to improve the mechanical properties and impact resistance of lightweight SCC10.1016/j.conbuildmat.2019.116944 ↗
77. Strength and permeation properties of self-compacting concrete containing fly ash and hooked steel fibres10.1016/j.conbuildmat.2015.11.044 ↗
78. Performance of high strength concrete made with copper slag as a fine aggregate10.1016/j.conbuildmat.2008.12.013 ↗
79. Singh, G., Siddique, R. 2016. Strength properties and micro-structural analysis of self-compacting.
80. concrete made with iron slag as partial replacement of fine aggregates. Construct. Build. Mater. 127, 144–152.
81. Influence of copper slag and metakaolin on the durability of self-compacting concrete10.1016/j.jclepro.2017.10.029 ↗
82. Stress-strain behavior of steel-fiber high-strength concrete under compression
83. On the prediction of the orientation factor and fibre distribution of steel and macro-synthetic fibres for fibre-reinforced concrete10.1016/j.cemconcomp.2016.11.008 ↗
84. Review paperestereology: historical perspective and applicability to concrete technology10.1617/s11527-005-9031-6 ↗
85. Stereological analysis of micromechanical behavior of concrete10.1007/BF02486497 ↗
86. Distribution of steel fibres in rectangular sections10.1016/j.cemconcomp.2004.03.005 ↗
87. Polyolefin fiber-reinforced concrete enhanced with steel-hooked fibers in low proportions10.1016/j.matdes.2014.03.050 ↗
88. Simple tools for fiber orientation prediction in industrial practice10.1016/j.cemconres.2011.05.008 ↗
89. Fibre spacing and specific fibre surface
90. On the orientation of fibres in structural members fabricated with self-compacting fibre reinforced concrete10.1016/j.cemconcomp.2011.09.005 ↗
91. Improved tensile performance with fiber reinforced self-compacting concrete
92. On the mechanical properties and fracture behavior of polyolefin fiber-reinforced self-compacting concrete10.1016/j.conbuildmat.2014.01.024 ↗
93. Experimental study on static and dynamic mechanical properties of steel fiber reinforced lightweight aggregate concrete10.1016/j.conbuildmat.2012.09.016 ↗
94. Use of steel and polypropylene fibers to improve flexural performance of deep soil–cement column10.1016/j.conbuildmat.2011.10.040 ↗
95. Comparative flexural behavior of four fiber reinforced cementitious composites10.1016/j.cemconcomp.2008.08.002 ↗
96. Influence of fibre type on flexural behaviour of self-compacting fibre reinforced cementitious composites10.1016/j.cemconcomp.2014.03.007 ↗
97. Flexural toughness of sustainable ECC with high-volume substitution of cement and silica sand10.1016/j.conbuildmat.2020.121438 ↗
98. Investigation of Flexural Toughness for Steel-and-Synthetic-Fiber-Reinforced Concrete Pipes10.1016/j.istruc.2018.12.010 ↗
99. Toughness evaluation of steel and polypropylene fiber reinforced concrete beams under bending
100. Flexural toughness and calculation model of super-fine stainless wire reinforced reactive powder concrete10.1016/j.cemconcomp.2019.103367 ↗