journal article·2014-09

Engineering properties of alkali-activated binders by use of desulfurization slag and GGBFS

Wen-Ten Kuo, Tsung-Chin Hou

Publisher page

Abstract

Abstract In this study, industrial by-products desulphurization slag powder (DS-P) and ground granulated blast furnace slag (GGBFS) were used as the raw materials for producing non-Portland-cement binders. Material properties and microstructures of the constituents were examined. Fresh behaviors, hardening properties and microstructures of the mortars made with these binders are also investigated. Experimental results showed that DS-P can provide sufficient alkali environment for activating the pozzolanic reactions of GGBFS. The mortar compressive strengths were shown to attain 17 MPa at 28 days of age. A linear proportion between DS-P content and required water amount is also found in the flow test. Increasing the amount of GGBFS would result in a shortened setting time; while increasing the DS-P content would gain a shorten time interval between initial and final setting. Our results suggested that the high alkali feature of DS-P can trigger the pozzolanic reactions of GGBFS mixtures for producing non-Portland-cement binders with satisfying qualities.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Concrete and Cement Materials Research · Magnesium Oxide Properties and Applications · Innovative concrete reinforcement materials

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (22)

Show source-provided references
1. Mechanical and microstructural properties of heat cured alkali-activated slag mortars10.1016/j.matdes.2011.10.005 ↗
2. Geopolymers: inorganic polymeric new materials10.1007/BF01912193 ↗
3. Compressive strength, modulus of elasticity, and water permeability of inorganic polymer concrete10.1016/j.matdes.2010.05.012 ↗
4. Alkali-activated binders: a review. Part 2. About materials and binders manufacture10.1016/j.conbuildmat.2007.03.019 ↗
5. Shi · 2006
6. Effect of type, form, and dosage of activators on strength of alkali-activated natural pozzolans10.1016/j.cemconcomp.2010.10.021 ↗
7. Influence of slag chemistry on the hydration of alkali-activated blast-furnace slag — Part II: effect of Al2O310.1016/j.cemconres.2011.08.005 ↗
8. Hydration of alkali-activated slag: comparison with ordinary Portland cement10.1680/adcr.2006.18.3.119 ↗
9. The calcium silicate hydrates10.1016/j.cemconres.2007.11.005 ↗
10. Hydration products of alkali activated slag cement10.1016/0008-8846(95)00045-E ↗
11. The coexistence of geopolymeric gel and calcium silicate hydrate at the early stage of alkaline activation10.1016/j.cemconres.2004.10.042 ↗
12. Alkali-activated cements opportunities and challenges10.1016/S0008-8846(98)00093-3 ↗
13. Mineralogical and microstructural characterization of alkali-activated fly ash/slag pastes10.1016/S0958-9465(02)00059-8 ↗
14. X-ray microtomography shows pore structure and tortuosity in alkali-activated binders10.1016/j.cemconres.2012.03.004 ↗
15. Chemical research and climate change as drivers in the commercial adoption of alkali activated materials10.1007/s12649-010-9015-9 ↗
16. Spatial distribution of pores in fly ash-based inorganic polymer gels visualised by Wood’s metal intrusion10.1016/j.micromeso.2009.05.016 ↗
17. Quantification of tortuosity in hardened cement pastes using synchrotron-based X-ray computed microtomography10.1016/j.cemconres.2009.03.005 ↗
18. Hydration products and strength development of calcium hydroxide-based alkali-activated slag mortars10.1016/j.conbuildmat.2011.10.063 ↗
19. High volume limestone alkali-activated cement developed by design of experiment10.1016/j.cemconcomp.2011.11.004 ↗
20. Alkali-activated slag cement and concrete: a review of properties and problems10.1680/adcr.1995.7.27.93 ↗
21. Alkali aggregate reaction in alkali slag cement mortars10.1007/BF02838542 ↗
22. Influence of the fineness of sewage sludge ash on the mortar properties10.1016/S0008-8846(03)00165-0 ↗