journal article·2019-03

Dependences of dynamic compressive and tensile strengths of four alkali-activated mortars on the loading rate and curing time

Wei Yao, Kaiwen Xia, Yanhui Liu, Yirui Shi, Karl Peterson

Publisher page

Abstract

Abstract There is recently an increasing interest in replacing ordinary Portland cement (OPC) with a sustainable binder used in construction materials because of heavy energy consumption and greenhouse gas emissions in OPC production. Alkali-activated binder made from industrial waste is therefore developed as an alternative to OPC. It is essential to assess the mechanical properties of construction materials using the new binders. Since materials behave differently when subjected to dynamic loading as compared to its response under static loading conditions, this paper aims to evaluate the mechanical properties of alkali-activated binder based mortars subjected to dynamic loading. Mortars containing low-calcium (fly-ash) and high-calcium (ground granulated blast-furnace slag) alkali-activated binders were tested. NaOH and sodium silicate solutions were used together as activators, and two groups of specimens made with different water ratios were tested for both fly-ash and blast furnace slag based mortars. The split Hopkinson pressure bar (SHPB) system was used to conduct dynamic tests, and dynamic compressive strength and tensile strength were measured to provide a comprehensive understanding of the dynamic behaviors of alkali-activated mortars. The results show that dynamic compressive and tensile strengths of alkali-activated mortars increase with the loading rates. In addition, water ratio and curing time significantly affect the dynamic compressive and tensile strengths of alkali-activated mortars. Finally, empirical formulas were established to describe dynamic behaviors for fly-ash and slag based mortars with different water ratios and curing time.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Concrete and Cement Materials Research · Rock Mechanics and Modeling · Innovative concrete reinforcement materials

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (55)

Show source-provided references
1. Geopolymers and other alkali activated materials: why, how, and what?10.1617/s11527-013-0211-5 ↗
2. Split tensile strength of slag-based boroaluminosilicate geopolymer10.1007/s41779-017-0127-6 ↗
3. Advances in alternative cementitious binders10.1016/j.cemconres.2010.11.012 ↗
4. Geopolymerization reaction to consolidate incoherent pozzolanic soil10.1007/s10853-007-2201-x ↗
5. Investigation of geopolymer mortar and concrete under high temperature
6. Geopolymers: inorganic polymeric new materials10.1007/BF01912193 ↗
7. Microstructural and mechanical properties of alkali activated Colombian raw materials10.3390/ma9030158 ↗
8. Microstructure and microanalysis of hardened cement pastes involving ground granulated blast-furnace slag10.1007/BF01133772 ↗
9. Early-age properties, strength development and heat of hydration of concrete containing various South African slags at different replacement ratios10.1016/j.conbuildmat.2011.06.018 ↗
10. Effects of type and dosage of alkaline activator and temperature on the properties of alkali-activated slag mixtures10.1016/j.conbuildmat.2006.07.002 ↗
11. Stabilization/solidification of hazardous and radioactive wastes with alkali-activated cements10.1016/j.jhazmat.2006.05.008 ↗
12. Phase transformation on heating of an aged cement paste10.1016/j.tca.2003.11.057 ↗
13. Sodium silicate-based, alkali-activated slag mortars: part I. Strength, hydration and microstructure10.1016/S0008-8846(02)00717-2 ↗
14. Other potential applications for alkali-activated materials
15. Alkali-activated fly ashes: a cement for the future10.1016/S0008-8846(98)00243-9 ↗
16. The characterization of hardened alkali-activated blast-furnace slag pastes and the nature of the calcium silicate hydrate (C-S-H) phase10.1016/0008-8846(94)90002-7 ↗
17. Hydration products of alkali activated slag cement10.1016/0008-8846(95)00045-E ↗
18. Pore solution chemistry of alkali-activated ground granulated blast-furnace slag110.1016/S0008-8846(98)00212-9 ↗
19. On the development of fly ash-based geopolymer concrete
20. Fracture properties of geopolymer paste and concrete10.1680/macr.2011.63.10.763 ↗
21. Tensile properties of fly ash/polyurea composites10.1007/s10853-011-5318-x ↗
22. Split tensile strength of OPC-based geopolymers: application of DOE method in evaluating the effect of production parameters and their optimum condition10.1016/j.ceramint.2014.03.094 ↗
23. Simultaneous effect of alkali activator and water/slag cement ratios on composites properties by full replacement of Portland cement
24. Hydration mechanism of composite binders containing blast furnace ferronickel slag at different curing temperatures10.1007/s10973-017-6739-9 ↗
25. A review of dynamic experimental techniques and mechanical behaviour of rock materials10.1007/s00603-013-0463-y ↗
26. Numerical investigation on the dynamic strength and failure behavior of rocks under hydrostatic confinement in SHPB testing10.1016/j.ijrmms.2018.05.008 ↗
27. Dynamic response and failure mechanism of brittle rocks under combined compression-shear loading experiments10.1007/s00603-017-1364-2 ↗
28. Mechanical properties of basalt fiber reinforced geopolymeric concrete under impact loading10.1016/j.msea.2008.11.063 ↗
29. Effect of strain rate on strength properties of low-calcium fly-ash-based geopolymer mortar under dry condition10.1007/s12517-011-0507-0 ↗
30. Research on the dynamic compressive test of highly fluidized geopolymer concrete10.1016/j.conbuildmat.2013.06.035 ↗
31. Effect of alkali-activator types on the dynamic compressive deformation behavior of geopolymer concrete10.1016/j.matlet.2014.03.102 ↗
32. Mechanical behavior of geopolymer concrete subjected to high strain rate compressive loadings10.1617/s11527-014-0322-7 ↗
33. ASTM C618-17a · 2017
34. Rickard · 2014 · 1
35. Dehghan Najmabadi · 2018
36. ASTM C192 / C192M-16a · 2016
37. Suggested methods for determining the dynamic strength parameters and mode-I fracture toughness of rock materials10.1016/j.ijrmms.2011.10.004 ↗
38. Energy Dispersive X-ray Spectroscopy
39. A review: the comparison between alkali-activated slag (Si+Ca) and metakaolin (Si+Al) cements10.1016/j.cemconres.2010.03.020 ↗
40. Do geopolymers actually contain nanocrystalline zeolites? A reexamination of existing results10.1021/cm050230i ↗
41. Hardening mechanisms of an alkaline-activated class F fly ash10.1016/S0008-8846(01)00571-3 ↗
42. Pulse shaping techniques for testing brittle materials with a split Hopkinson pressure bar10.1007/BF02411056 ↗
43. Dynamic rock tests using split Hopkinson (Kolsky) bar system – a review10.1016/j.jrmge.2014.07.008 ↗
44. Critical appraisal of limiting strain rates for compression testing of ceramics in a split Hopkinson pressure bar10.1111/j.1151-2916.1994.tb06987.x ↗
45. Dynamic mechanical behaviors of Fangshan marble10.1016/j.jrmge.2017.03.019 ↗
46. Dynamic Brazilian tests of granite under coupled static and dynamic loads10.1007/s00603-013-0441-4 ↗
47. Dependence of dynamic tensile strength of Longyou sandstone on heat-treatment temperature and loading rate10.1007/s00603-015-0895-7 ↗
48. ASTM C39/C39M-18 · 2018
49. Suggested methods for determining tensile strength of rock materials10.1016/0148-9062(78)90003-7 ↗
50. Thermal degradation of dynamic compressive strength for two mortars10.1016/j.conbuildmat.2017.01.048 ↗
51. Split-Hopkinson pressure-bar tests on concrete and mortar in tension and compression
52. Dynamic behavior of concrete at high strain rates and pressures: I. Experimental characterization10.1016/S0734-743X(01)00020-3 ↗
53. Review of mechanical properties of HSC at elevated temperature10.1061/(ASCE)0899-1561(1998)10:1(58) ↗
54. Effects of mineral admixtures and lime on disintegration of alkali-activated slag exposed to 50 °C10.1016/j.conbuildmat.2014.07.101 ↗
55. Synthesis and characterisation of materials based on inorganic polymers of alumina and silica: sodium polysialate polymers10.1016/S1466-6049(00)00041-6 ↗