Bending behavior of engineered cementitious composites (ECC) with different recycled and virgin polymer fibers
Source abstract
Abstract
This study evaluated Engineered Cementitious Composites (ECC) with polyvinyl alcohol (PVA), polypropylene (PP) or recycled polyester (POL) fibers inserted in a matrix with elevated silica fume content. Several PP (2.2–2.6%) and POL (2.3–2.7%) contents were tested and compared to a compound containing 2.0% PVA. Flexural bending strength tests, the bending rupture modulus, number and width of cracks and deformation were measured at 5 different curing ages (7, 14, 28, 56 e 84 days). The test results also showed that in the fresh state, ECCPVA2.0 presented the best result with an average spread of 255 mm, followed by ECCPP2.4 and ECCPOL2.3. All Γ values obtained confirmed that all composites attained plastic consistency. In the hardened state, composites with POL fibers had tensile strength performance similar to PVA fibers with regards to deformation, deflection, rupture modulus, average crack width and number of cracks. In addition, ECCPOL2.7 demonstrated mechanical properties superior to ECCPVA2.0. So, the use of 2.7% POL content resulted in strengths higher than the reference PVA compound and demonstrated the potential of POL fibers in ECC development at ages over 28 days. The use of recycled POL fibers, at a content of 2.7%, resulted in an increase in the ductility of the composite, reaching the values of ECC-PVA at 28 and 84 days. On the other hand, PP composites did not present the expected behavior of an ECC. More specifically, the matrix had high tensile strength, modulus of elasticity and tenacity, which limited crack formation and overloaded the reinforcement fibers. Thus, PP fibers were deemed incompatible for ECCs with rich matrices.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Innovative concrete reinforcement materials · Structural Behavior of Reinforced Concrete · Recycled Aggregate Concrete Performance
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (71)
Show source-provided references
1. Engineered cementitious composites with high-volume fly ash
2. Repeatability and pervasiveness of self-healing in engineered cementitious composites
3. Supplemental use of rice husk ash (RHA) as a cementitious material in concrete industry10.1016/j.conbuildmat.2018.05.101 ↗
4. Effect of cracking localization on the structural ductility of normal strength and high strength reinforced concrete beams with steel fibers10.1177/2041419618824609 ↗
5. J. Xue, et al. Seismic resistance capacity of steel reinforced high-strength concrete columns with rectangular spiral stirrups. Construction and Building Materials, Guildford, Surrey, v. 229, art. 116880, 2019. DOI: https://doi.org/10.1016/j.conbuildmat.2019.116880.10.1016/j.conbuildmat.2019.116880 ↗
6. Proposition of Mixture Design Method for Ultra-High-Performance Concrete
7. Enhancing corrosion resistance of reinforced concrete structures with hybrid fiber reinforced concrete10.1016/j.corsci.2014.12.003 ↗
8. A.M. Neville, J.J. Brooks, Tecnologia do concreto. 2. ed. Porto Alegre: Bookman, 2013. E-book.
9. Coupled effects of limestone powder and high-volume fly ash on mechanical properties of ECC10.1016/j.conbuildmat.2017.12.186 ↗
10. On the use of recycled tire rubber to develop low e-modulus ECC for durable concrete repairs10.1016/j.conbuildmat.2013.04.027 ↗
11. M. Singh, B. Saini, H.D. Chalak, Performance and composition analysis of engineered cementitious composite (ECC): a review. Journal of Building Engineering, Oxford, v. 26, art. 100851, 2019.10.1016/j.jobe.2019.100851 ↗
12. Q. Wang, et al. Greener engineered cementitious composite (ECC): the use of pozzolanic fillers and unoiled PVA fibers. Construction and Building Materials, Guildford, Surrey, v. 247, art. 118211, 2020. DOI: https://doi.org/10.1016/j.conbuildmat.2020.118211.10.1016/j.conbuildmat.2020.118211 ↗
13. S. Wang, Micromechanics based matrix design for engineered cementitious composites. 2005. Dissertation (Degree of Doctor of Philosophy, Civil Engineering) -- Horace H. Rackham School of Graduate Studies, University of Michigan, Michigan, 2005.
14. Mechanical, physical, and self-healing behaviors of engineered cementitious composites with glass powder
15. Innovative crack-healing hybrid fiber reinforced engineered cementitious composite10.1016/j.conbuildmat.2017.06.023 ↗
16. Cements of yesterday and today - concrete of tomorrow10.1016/S0008-8846(00)00365-3 ↗
17. ASTM C188. Standard Test Method for Density of Hydraulic Cement. American Society for Testing and Materials (ASTM), Pensilvânia, 2017.
18. ASTM C150/C150M. Standard Specification for Portland Cement. American Society for Testing and Materials (ASTM), Pensilvânia, 2021.
19. Self-Healing Capability of Engineered Cementitious Composites Incorporating Different Types of Pozzolanic Materials By Author ’ s
20. A. Bentur, S. Mindess, Fibre Reinforced Cementitious Composites. Taylor & F ed. New York: 2007.10.1201/9781482267747 ↗
21. New models for predicting workability and toughness of hybrid fiber reinforced cement-based composites10.1016/j.conbuildmat.2018.05.075 ↗
22. Experimental study of some durability properties of ECC with a more environmentally sustainable rice husk ash and high tenacity polypropylene fibers10.1016/j.conbuildmat.2019.04.092 ↗
23. Utilization of Local Ingredients for the Production of High-Early-Strength Engineered Cementitious Composites
24. Experimental method for investigating the impact of the addition of polymer fibers on drying shrinkage and cracking of concrete10.1002/suco.201800228 ↗
25. Análise comparativa da retração por secagem de concretos com fibras novas e recicladas de poliéster10.1590/s1678-86212018000300276 ↗
26. Fiber volume fraction and ductility index of concrete beams10.1016/j.cemconcomp.2015.10.019 ↗
27. Influence of matrix flowability, fiber mixing procedure, and curing conditions on the mechanical performance of HTPP-ECC10.1016/j.compositesb.2013.12.076 ↗
28. Effect of shrinkage-reducing admixture and expansive agent on mechanical properties and drying shrinkage of Engineered Cementitious Composite (ECC)10.1016/j.conbuildmat.2018.05.203 ↗
29. Investigação do Comportamento de Engineered Cementitious Composites Reforçados com Fibras de Polipropileno como Material para Recapeamento de Pavimentos
30. Direct-tensile and flexural strength and toughness of high-strength fiber-reinforced cement composites with different steel fibers10.18702/acf.2016.06.2.1.67 ↗
31. Properties of polyvinyl alcohol fiber as reinforcing materials for cementitious composites
32. JSCE 82. Recommendations for Design and Construction of High Performance Fiber Reinforced Cement Composites with Multiple Fine Cracks (HPFRCC). Concrete Engineereing Series, v. 82, p. Testing Method 6-10, 2008.
33. Avaliação da resistência a fadiga dos Engineered Cementitious Composites (ECC), reforçados com fibra de polipropileno e produzidos com adição de cinza de casca de arroz10.17058/tecnolog.v21i2.9336 ↗
34. M. Keskinates, B. Felekoglu, The influence of mineral additive type and water / binder ratio on matrix phase rheology and multiple cracking potential of HTPP-ECC. v. 173, p. 508–519, 2018.10.1016/j.conbuildmat.2018.04.038 ↗
35. Development of a self-consolidating engineered cementitious composite employing electrosteric dispersion/stabilization10.1016/S0958-9465(02)00057-4 ↗
36. Fillers to improve passing ability of concrete10.1002/suco.201800047 ↗
37. Dilatancy mitigation of cement powder paste by pozzolanic and inert fillers10.1002/suco.201900320 ↗
38. Cause and mitigation of dilatancy in cement powder paste10.1016/j.conbuildmat.2019.117595 ↗
39. B. Lhoneux, DE et al. Development of High Tenacity Polypropylene Fibres for Cementitious Composites. JCI International Workshop on Ductile Fiber Reinforced Cementitious Composites (DFRCC) Application and Evaluation, n. October 2014, p. 121–131, 2002.
40. Li · 2019
41. Steady-State and Multiple Cracking of Short Random Fiber Composites
42. Microstructure variability and macroscopic composite properties of high performance fiber reinforced cementitious composites10.1016/j.probengmech.2005.10.008 ↗
43. Recycling polyethylene terephthalate wastes as short fibers in Strain-Hardening Cementitious Composites (SHCC)10.1016/j.jhazmat.2018.05.046 ↗
44. Tensile performance and impact resistance of Strain Hardening Cementitious Composites (SHCC) with recycled fibers10.1016/j.conbuildmat.2018.03.108 ↗
45. Flexural strength of fiber10.1061/(ASCE)0899-1561(1994)6:3(390) ↗
46. Caracterização experimental de compósitos cimentícios reforçados com fibras de PVA: processo de fratura, propriedades térmicas, deformações diferidas e estabilidade térmica
47. Mechanical behaviour of a polyvinyl alcohol fibre reinforced engineered cementitious composite (PVA-ECC) using local ingredients10.1016/j.conbuildmat.2017.02.158 ↗
48. W. Meng, Khayat, K. H. Effect of graphite nanoplatelets and carbon nanofibers on rheology, hydration, shrinkage, mechanical properties, and microstructure of UHPC. Cement and Concrete Research, v. 105, n. May 2017, p. 64–71, 2018.10.1016/j.cemconres.2018.01.001 ↗
49. The effect of hybridization and geometry of polypropylene fibers on engineered cementitious composites reinforced by polyvinyl alcohol fibers10.1177/0021998315586078 ↗
50. Micromechanics-based investigation of fatigue deterioration of engineered cementitious composite (ECC)10.1016/j.cemconres.2017.02.029 ↗
51. Composite properties of high-Strength, high-Ductility concrete
52. Impact resistance of high strength-high ductility concrete10.1016/j.cemconres.2017.03.013 ↗
53. J.D. Rathod, S.C. Patodi, Interface Tailoring of Polyester-Type Fiber in Engineered Cementitious Composite Matrix against Pullout. ACI Materials Journal, v. 107, n. 2, 2010.10.14359/51663574 ↗
54. D.P. Righi, et al. Tensile behaviour and durability issues of Engineered Cementitious Composites with Rice Husk Ash. Revista Materia, v. 22, n. 2, 2017.10.1590/s1517-707620170002.0182 ↗
55. Avaliação do comportamento mecânico de um ECC (Engineered Cementitious Composites)
56. Frost resistance and microstructure of Engineered Cementitious Composites: Influence of fly ash and micro poly-vinyl-alcohol fiber10.1016/j.cemconcomp.2011.10.002 ↗
57. Improving the workability and rheological properties of Engineered Cementitious Composites using factorial experimental design10.1016/j.compositesb.2012.08.015 ↗
58. The effect of synthetic polyethylene fiber on the strain hardening behavior of engineered cementitious composite (ECC)10.1016/j.matdes.2015.07.125 ↗
59. A self-reinforced cementitious composite for building-scale 3D printing10.1016/j.cemconcomp.2018.03.017 ↗
60. H. Stang, C. Li, Extrusion of ECC-Material.pdf. p. 1–10, 1999.
61. Strain-hardening UHP-FRC with low fiber contents
62. Academic research institutes-construction enterprises linkages for the development of urban green building: Selecting management of green building technologies innovation partner
63. Development of cost effective ultra-high-performance fiber-reinforced concrete using single and hybrid steel fibers10.1016/j.conbuildmat.2017.06.018 ↗
64. Mechanical performance of ECC with high-volume fly ash after sub-elevated temperatures10.1016/j.conbuildmat.2015.09.002 ↗
65. Development of ultra-high performance engineered cementitious composites using polyethylene (PE) fibers10.1016/j.conbuildmat.2017.10.040 ↗
66. Experimental and numerical investigations on seismic responses of reinforced concrete structures considering strain rate effect10.1016/j.conbuildmat.2018.04.085 ↗
67. Influence of bacterial incorporation on mechanical properties of engineered cementitious composites (ECC)10.1016/j.conbuildmat.2018.11.089 ↗
68. Investigating mechanical properties and self-healing behavior of micro-cracked ECC with different volume of fly ash10.1016/j.conbuildmat.2013.11.001 ↗
69. Multiple-scale investigations on self-healing induced mechanical property recovery of ECC10.1016/j.cemconcomp.2019.05.014 ↗
70. Improved fiber distribution and mechanical properties of engineered cementitious composites by adjusting the mixing sequence10.1016/j.cemconcomp.2011.11.019 ↗
71. R.G. Pillai, R. Gettu, M. Santhanam, Uso de materiais cimentícios suplementares (SCMs) em sistemas de concreto armado - Benefícios e limitações. Revista ALCONPAT, Volume 10, Número 2 (maio – agosto, 2020): 147 – 164.10.21041/ra.v10i2.477 ↗