Effect of BaCl2 on the hydration properties of ultrahigh performance geopolymer concrete
Source abstract
Abstract
Ultrahigh performance geopolymer concrete (UHPGC) is a new construction material with ultrahigh mechanical properties and excellent durability. However, UHPGC is difficult to use in practical engineering due to its short setting time and high viscosity. Therefore, increasing the setting time and improving the working performance of UHPGC is critical. In this paper, effects of BaCl 2 on the setting time, hydration property, rheological property and mechanical property of UHPGC were investigated by testing the setting time, fluidity, plastic viscosity, compressive and flexural strength. Furthermore, the retarding mechanism of setting was also discussed. The results indicated that with increasing of BaCl 2 content, the early hydration of UHPGC was delayed, and the compressive strength first increased and then decreased. SiO 3 2− ions were consumed by the incorporation of BaCl 2 and generated a large amount of BaSiO 3 precipitate, which wrapped the slag particles, and the further hydration of slag was delayed. Consequently, the plastic viscosity and yield stress were reduced, the fluidity was improved, and the working performance was enhanced.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Concrete and Cement Materials Research · Innovations in Concrete and Construction Materials · Innovative concrete reinforcement materials
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (51)
Show source-provided references
1. Introduction to environment and development
2. Z. Şen, Climate change, droughts, and water resources, applied drought modeling, prediction, and mitigation 2015, pp. 321-391.10.1016/B978-0-12-802176-7.00006-7 ↗
3. Bio-mineralization on cement-based materials consuming CO2 from atmosphere10.1016/j.conbuildmat.2015.10.105 ↗
4. Novel application of low carbon limestone calcined clay cement (LC3) in expansive soil stabilization: an eco-efficient approach10.1016/j.jclepro.2022.133492 ↗
5. Lightweight concrete from a perspective of sustainable reuse of waste byproducts10.1016/j.conbuildmat.2021.126061 ↗
6. Importance and potential of cellulosic materials and derivatives in extrusion-based 3D concrete printing (3DCP): prospects and challenges10.1016/j.conbuildmat.2021.123281 ↗
7. A review on mixture design methods for geopolymer concrete10.1016/j.compositesb.2019.107490 ↗
8. Recent progress in low-carbon binders10.1016/j.cemconres.2019.05.009 ↗
9. 2006
10. A comprehensive overview about the influence of different additives on the properties of alkali-activated slag – a guide for civil engineer10.1016/j.conbuildmat.2013.04.011 ↗
11. Alkali-activated fly ash/slag cements: strength behaviour and hydration products10.1016/S0008-8846(00)00298-2 ↗
12. Fly ash-based geopolymers: the relationship between composition, pore structure and efflorescence10.1016/j.cemconres.2014.06.004 ↗
13. Structural and material performance of geopolymer concrete: a review10.1016/j.conbuildmat.2018.07.111 ↗
14. Mechanical and flexural performance of synthetic fibre reinforced geopolymer concrete10.1016/j.conbuildmat.2018.07.110 ↗
15. Development of rubberized geopolymer concrete: strength and durability studies10.1016/j.conbuildmat.2019.01.185 ↗
16. Conversion of local industrial wastes into greener cement through geopolymer technology: a case study of high-magnesium nickel slag10.1016/j.jclepro.2016.09.147 ↗
17. Optimization for the preparation of composite geopolymer using response surface methodology and its application in lead-zinc tailings solidification10.1016/j.conbuildmat.2020.120969 ↗
18. A comparative study on solidification/stabilization characteristics of coal fly ash-based geopolymer and Portland cement on heavy metals in MSWI fly ash10.1016/j.jclepro.2021.128790 ↗
19. Solidification/stabilization and separation/extraction treatments of environmental hazardous components in electrolytic manganese residue: a review10.1016/j.psep.2021.10.031 ↗
20. Fly ash and zinc slag blended geopolymer: Immobilization of hazardous materials and development of paving blocks10.1016/j.jhazmat.2019.121673 ↗
21. Investigation on some factors affecting the characteristics of alkali-phosphorus slag cement10.1016/0008-8846(89)90004-5 ↗
22. Experimental verification of the feasibility of a novel prestressed reactive powder concrete box-girder bridge structure10.1061/(ASCE)BE.1943-5592.0001033 ↗
23. Design and behavior of super-long span cable-stayed bridge with CFRP cables and UHPC members10.1016/j.compositesb.2018.11.060 ↗
24. A review on ultra high performance concrete: part II. hydration, microstructure and properties10.1016/j.conbuildmat.2015.08.095 ↗
25. A review on ultra high performance concrete: part I. raw materials and mixture design10.1016/j.conbuildmat.2015.10.088 ↗
26. Influence of superplasticizers and retarders on the workability and strength of one-part alkali-activated fly ash/slag binders cured at room temperature10.1016/j.conbuildmat.2019.116891 ↗
27. Development of ultra-high-performance geopolymer concrete10.1680/macr.13.00057 ↗
28. Development of ultra-high performance geopolymer concrete (UHPGC): influence of steel fiber on mechanical properties10.1016/j.cemconcomp.2020.103670 ↗
29. Development and preliminary mix design of ultra-high-performance concrete based on geopolymer10.1016/j.conbuildmat.2021.125110 ↗
30. The setting time of a clay-slag geopolymer matrix: the influence of blast-furnace-slag addition and the mixing method10.1016/j.jclepro.2015.05.069 ↗
31. Setting time and 7-day strength of geopolymer mortar with various binders10.1016/j.conbuildmat.2018.08.025 ↗
32. Alkali-activated slag mortars Mechanical strength behaviour10.1016/S0008-8846(99)00154-4 ↗
33. Geopolymerisation kinetics. 3. Effects of Cs and Sr salts10.1016/j.ces.2008.06.008 ↗
34. Sodium silicate-based, alkali-activated slag mortars10.1016/S0008-8846(02)00717-2 ↗
35. Enhancement of the properties of silicate activated ultrafine-slag based geopolymer mortar using retarder10.1016/j.conbuildmat.2021.125380 ↗
36. Standard test method for flexural toughness and first-crack strength of fiber-reinforced concrete (using beam with third-point loading)
37. EN BS. 459-2, Building Lime, Part 2: Test Method, British-Adopted European Standard, 2010, 2010.
38. Rheological and harden properties of the high-thixotropy 3D printing concrete10.1016/j.conbuildmat.2018.12.061 ↗
39. Rheological properties, shape stability and compressive strength of 3D printed colored cement composites modified by needle-like pigment
40. Rheological, fresh, and mechanical properties of mechanochemically activated geopolymer grout: a comparative study with conventionally activated geopolymer grout10.1016/j.conbuildmat.2022.126338 ↗
41. Rheological requirements for printable concretes10.1016/j.cemconres.2018.04.005 ↗
42. Low field NMR relaxation as a probe to study the effect of activators and retarders on the alkali-activated GGBFS setting process10.1016/j.cemconcomp.2019.103399 ↗
43. Effect of chemical admixtures on properties of high-calcium fly ash geopolymer10.1007/s12613-011-0448-3 ↗
44. Soil-silicate concrete for hydraulic and irrigation structures10.1007/BF02379128 ↗
45. Phase evolution of C-(N)-A-S-H/N-A-S-H gel blends investigated via alkali-activation of synthetic calcium aluminosilicate precursors10.1016/j.cemconres.2016.08.010 ↗
46. Using hazardous barium slag as a novel admixture for alkali activated slag cement10.1016/j.cemconcomp.2021.104332 ↗
47. Synergistic positive effects of nano barium silicate on the hydration rate and phase composition of alkali-activated slag
48. Chemical evaluation of immobilization of wastes containing Pb, Cd, Cu and Zn in alkali-activated materials: a critical review10.1016/j.jece.2020.104194 ↗
49. Immobilization of chromite ore processing residue with alkali-activated blast furnace slag-based geopolymer10.1016/j.ceramint.2016.03.033 ↗
50. Stabilization of lead in an alkali-activated municipal solid waste incineration fly ash–Pyrophyllite-based system10.1016/j.jenvman.2017.07.002 ↗
51. EPA (Environmental Protection Agency), Test methods for evaluating solid wastes Physical/chemical methods: EPA METHOD 1311, toxicity characteristic leaching procedure, SW-846, Washington.