Characterization of mechanical behavior of different types of masonry with a detailed investigation of full-field strain using digital image correlation
Source abstract
Abstract
This article presents an experimental study on the mechanical characterization of three different types of masonry: burnt clay bricks, fly ash bricks, and autoclaved aerated concrete (AAC) blocks, with a detailed focus on strain distribution and failure mechanism. The specimens were subjected to direct and diagonal compression loading, and the stress–strain curves and failure modes were studied. Digital image correlation (DIC) was used to obtain full-field strain data, allowing for detailed analysis of failure mechanisms, tracking of crack propagation, and examination of other intricate details. The DIC analysis showed that in burnt clay brick and fly ash brick masonry, failure under compression was initiated by the tensile splitting of the brick, while in AAC block masonry, it was initiated by the tensile splitting of the mortar. Additionally, the study identified that the failure modes under diagonal compression were different for each type of masonry, with bed joint sliding being the dominant failure mode in fly ash brick and AAC block masonry. In contrast, the failure mode in burnt clay brick masonry was due to vertical splitting along the loaded diagonal. In the diagonal compression test, the shear strain along both diagonals was negligible, and principal strain directions were observed to be aligned along the two diagonals.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Masonry and Concrete Structural Analysis · Building materials and conservation · Hygrothermal properties of building materials
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (68)
Show source-provided references
1. Masonry composite material made of limestone powder and fly ash10.1016/j.powtec.2010.07.004 ↗
2. Manufacturing of building bricks without Portland cement10.1016/j.jclepro.2012.07.047 ↗
3. A proposed failure theory for brick masonry in compression
4. Mechanics of masonry in compression10.1061/(ASCE)0733-9445(1985)111:4(857) ↗
5. Drysdale · 1999
6. Brick-mortar bond and masonry compressive strength10.1061/(ASCE)0899-1561(2005)17:2(229) ↗
7. Stress-strain characteristics of clay brick masonry under uniaxial compression10.1061/(ASCE)0899-1561(2007)19:9(728) ↗
8. Suitability of half-scale burnt clay bricks for shake table tests on masonry walls10.1061/(ASCE)MT.1943-5533.0000861 ↗
9. Assessment of the characteristics of lime mortar bonded brickwork wallettes under monotonic and cyclic compression10.1016/j.conbuildmat.2020.120003 ↗
10. Effect of structural bonding patterns on mechanical characteristics of clay brick masonry under different loadings using digital image correlation technique10.1061/(ASCE)MT.1943-5533.0004457 ↗
11. A detailed experimental mechanical characterization of multi-perforated clay brick masonry
12. An experimental study on the mechanical properties of solid clay brick masonry with traditional mortars
13. A perspective study on fly ash–lime–gypsum bricks and hollow blocks for low cost housing development10.1016/S0950-0618(02)00034-X ↗
14. Experimental study on axial compressive strength and elastic modulus of the clay and fly ash brick masonry
15. Evaluation of nonlinear material properties of fly ash brick masonry under compression and shear10.1061/(ASCE)MT.1943-5533.0001188 ↗
16. Variability in the compressive strength of fly ash bricks10.1061/(ASCE)MT.1943-5533.0002592 ↗
17. Quantification of uncertainty in compressive strength of fly ash brick masonry
18. Experimental Study on Mechanical and Durability Properties of Fly Ash-Lime-Slag Block for Dry Stack Masonry Construction10.1061/(ASCE)MT.1943-5533.0004652 ↗
19. Compressive Strength Prediction Models for Fly-Ash Brick Masonry10.1061/(ASCE)SC.1943-5576.0000693 ↗
20. Mechanical characterization of autoclaved aerated concrete masonry subjected to in-plane loading: Experimental investigation and FE modeling10.1016/j.conbuildmat.2015.08.121 ↗
21. Experimental investigation of autoclaved aerated concrete masonry10.1061/(ASCE)MT.1943-5533.0002762 ↗
22. Evaluation of mechanical properties of autoclaved aerated concrete (AAC) block and its masonry
23. Bond strength of Autoclaved Aerated Concrete (AAC) masonry using various joint materials
24. Analysis of confined AAC walls under monotonic compression10.1016/j.engstruct.2021.113756 ↗
25. ASTM (American Society for Testing Materials), Standard test method for compressive strength of masonry prisms, ASTM C1314, ASTM, West Conshohocken, 2021.
26. CEN (European Committee of Standardization), Methods of test for masonry: Part 1: Determination of compressive strength, EN 1052-1, CEN, Brussels, Belgium, 1999.
27. K. Gumaste, K. Nanjunda Rao, B. Venkatarama Reddy, K. Jagadish, Strength and elasticity of brick masonry prisms and wallettes under compression, Mater Struct . 40(2) (2007) 241-253. https://doi.org/10.1617/s11527-006-9141-9.10.1617/s11527-006-9141-9 ↗
28. Strength, behavior, and failure mode of hollow concrete masonry constructed with mortars of different strengths10.1016/j.conbuildmat.2016.12.112 ↗
29. Correlation between the performance of solid masonry prisms and wallettes under compression10.1016/j.jobe.2019.01.007 ↗
30. Variation in compressive properties of Indian brick masonry and its assessment using empirical models10.1016/j.istruc.2021.05.063 ↗
31. In-plane response of masonry infill walls: experimental study using digital image correlation10.1016/j.proeng.2015.08.042 ↗
32. Masonry walls subjected to in-plane cyclic loading: application of digital image correlation for deformation field measurement
33. Digital image correlation for the analysis of in-plane tested unreinforced masonry walls10.1016/j.istruc.2020.11.051 ↗
34. Experimental analysis of diagonal compression and splitting tests for the characterization of shear and tensile behavior of adobe masonry10.1016/j.engstruct.2020.110633 ↗
35. Experimental testing and finite element modelling of earth block masonry10.1016/j.engstruct.2015.09.020 ↗
36. Basic principle of digital image correlation for in-plane displacement and strain measurement10.1080/09243046.2015.1129681 ↗
37. Constitutive behaviour of masonry prisms using a full-field measurement technique10.1016/j.istruc.2022.11.008 ↗
38. Compressive strength and deformation characteristics of concrete block masonry made with different mortars, blocks and mortar beddings types
39. Solutions · 2009
40. ASTM (American Society for Testing Materials), Standard test methods for sampling and testing brick and structural clay tile., ASTM C67/C67M, ASTM., West Conshohocken, 2021.
41. Relations between structure and mechanical properties of autoclaved aerated concrete10.1016/0008-8846(79)90049-8 ↗
42. Strength properties of autoclaved cellular concrete with high volume fly ash10.1061/(ASCE)0733-9402(1997)123:2(44) ↗
43. Matthys · 1999
44. Influence of water absorption on properties of AAC and CLC lightweight concrete brick
45. Hygric, thermal and durability properties of autoclaved aerated concrete10.1016/j.conbuildmat.2012.12.036 ↗
46. Utilization of crushed clay brick in cellular concrete production10.1016/j.aej.2013.11.005 ↗
47. CEN (European Committee of Standardization) · 2015
48. BIS (Bureau of Indian Standards) · 2016
49. ANSI (American National Standard Institute), American National Standard specifications for modified dry-set cement mortar, ANSI A118.4, ANSI, New York, 2012.
50. ASTM (American Society for Testing Materials), Standard test method for diagonal tension (shear) in masonry assemblages., ASTM E519/E519M, ASTM, West Conshohocken, 2021.
51. RILEM, LUM B6 Diagonal tensile strength tests of small wall specimens, 1991, RILEM Recommendations Test. Use Constr. Mater. 30 (1994) 488-489. https://doi.org/10.1201/9781482271362.10.1201/9781482271362 ↗
52. An earth block with a compressive strength higher than 45 MPa!10.1016/j.conbuildmat.2013.05.068 ↗
53. Methodological issues for the mechanical characterization of unfired earth bricks10.1016/j.conbuildmat.2018.04.118 ↗
54. CEN (European Committee of Standardization), Methods of test for masonry units-part 1. Determination of compressive strength, EN 772-1:2011+A1:2015 CEN, Brussels, Belgium, 2015.
55. MSJC (Masonry Standards Joint Committee), Building Code Requirements and Specification for Masonry Structures, MI: MSJC, Farmington Hills, 2013.
56. Out-of-plane behaviour of unreinforced masonry strengthened using ferrocement overlay10.1617/s11527-014-0390-8 ↗
57. Feasibility study on utilization of municipal solid waste incineration bottom ash as aerating agent for the production of autoclaved aerated concrete10.1016/j.cemconcomp.2014.11.006 ↗
58. The effect of density on the delicate balance between structural requirements and environmental issues for AAC blocks: An experimental investigation10.3390/su132313186 ↗
59. Aroni · 1993
60. BIS (Bureau of Indian Standards), Common burnt clay building bricks—Specification (First Version), IS 1077, BIS, New Delhi, India, 1992.
61. BIS (Bureau of Indian Standards), Indian standard pulverized fuel ash-lime bricks—Specification (First Version), IS 12894, BIS, New Delhi, India, 2002.
62. Taha · 2001
63. M. Simonsen, Strain tensors and criteria in Vic, Correlated Solutions, Inc. , 2020. https://correlated.kayako.com/article/2-strain-tensors-and-criteria-in-vic#:∼:text=The%20Lagrangian%20finite%20strain%20tensor,large%20strains%20such%20as%20elastomers. (Accessed May 02, 2023.
64. Identification of shear parameters of masonry panels through the in-situ diagonal compression test10.1080/15583050802138634 ↗
65. CEN (European Committee of Standardization), Design of masonry structures. Part 1-1: General rules for reinforced and unreinforced masonry. European Committee of Standardization, Eurocode 6, CEN, Belgium, 2005.
66. ASCE (American Society of Civil Engineers) · 2017
67. Flexural strength of AAC masonry with bed joint reinforcement10.1002/cepa.887 ↗
68. Mechanical properties characterization of different types of masonry infill walls10.1007/s11709-019-0602-y ↗