INFLUENCE OF AXISYMMETRIC DEFORMATION PROCESSING METHODS ON THE MECHANICAL PROPERTIES OF Cu-Nb COMPOSITES
Source abstract
Abstract
ABSTRACT It has been shown that deformation processed Cu-19% Nb alloys with good strength and electrical conductivity can be developed in sizes that are useful for engineering applications. Mot extrusion of bundled sub-elemental Cu-19% Nb wires followed by cold drawing to make a composite wire of diameter equal to that of the initial sub-elemental wires resulted in a 67% increase in the ultimate tensile stress. However, on subsequent cold drawing of this composite wire the strength increased at a slower rate than that obtained on continuing cold drawing of the sub-elemental wire and the strength differential decreased. In addition, after cold drawing to equivalent diameters the electrical conductivity of the composite wire was less than that of the sub-elemental wire. These results indicate that while high strengths and good electrical conductivities can be produced in larger size deformation processed Cu-Nb composites by a process of bundling, extrusion and cold drawing of sub-elemental wires, there appears to be a limit to the amount of subsequent cold drawing feasible before the benefit in properties ceases.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Microstructure and mechanical properties · Copper Interconnects and Reliability · Aluminum Alloys Composites Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (14)
Show source-provided references
1. Bevk , J. , W.A. Sunder , G.Dublon and D.E. Cohen , in Situ Composites IV (eds. F.D. Lemkey, H.E. Cline and M. McLean ), Elsevier , Amsterdam , p. 121 , ( 1982 ).
2. Hosford W.F. · Transactions of AIME · 1964 · 230 · 12
3. 10.1063/1.34302410.1063/1.343024 ↗
4. Renaud , C.V. , E. Gregory and J. Wong , in Advances in Cryogenic Engineering Materials , ( ed. R.P. Reed and A.F. Clark ), Vol.32 , Plenum Press , New York , p. 443 , ( 1986 ).10.1007/978-1-4613-9871-4_54 ↗
5. Renaud , C.V. , E. Gregory and J. Wong , in Advances in Cryogenic Engineering Materials , ( ed. R.P. Reed and AF. Clark ), Vol.34 , Plenum Press , New York , p. 435 , ( 1988 ).
6. 10.1007/BF0072803510.1007/BF00728035 ↗
7. Verhoeven J.D. · Journal of Metals · 1986 · 38 · 20
8. 10.1063/1.9750310.1063/1.97503 ↗
9. Underwood , E.E. , Quantitative Stereology , Addison-Wesley , Reading , Massachusetts , Chapters 3 and 4, ( 1970 ).
10. Laabs , F.C. , A.R. Pelton and W.A. Spitzig , in Microbeam Analysis , ( ed. A.D. Romig, Jr. and W.F. Chambers ), San Francisco Press , California , p. 328 , ( 1986 ).
11. 10.1016/0304-3991(87)90069-610.1016/0304-3991(87)90069-6 ↗
12. Laabs , F.C. and L.S. Chumbley , unpublished research , Ames Laboratory , Ames , IA , ( 1990 ).
13. Verhoeven , J.D. and E.D. Gibson , unpublished research , Ames Laboratory , Ames , IA , ( 1989 ).
14. 10.1109/TMAG.1983.106250210.1109/TMAG.1983.1062502 ↗