journal article·2022-10-20Open access

Tribological Characteristics of High-Chromium Based Multi-Component White Cast Irons

Riki Hendra Purba, Kazumichi Shimizu, Kenta Kusumoto, Yila Gaqi, Mohammad Jobayer Huq

Crystals· Volume 12· Issue 10

Abstract

It has been evaluated the relationship between the microstructure and three-body abrasive wear behavior of high-chromium (18 and 27 mass % Cr) based (3 mass % each of V, Mo, W, and Co) multicomponent white cast iron materials (high-Cr MWCIs). It was also compared to MWCI to determine the service life of the materials. The results indicate that the microstructure of the material is composed of mainly martensite matrix and different types of precipitated carbides. The wear resistances of both the high-Cr MWCIs are higher than MWCI owing to the higher hardness (4–18% increment in hardness), although they contain fewer carbide types. The carbide volume fraction of high-Cr MWCI increases with increase in the Cr content, but the hardness decreases, leading to a reduction in wear resistance. This is because the transition metal significantly consumes C atoms to form more eutectic carbides during solidification, which is exacerbated by the depletion of C in the matrix during heat treatment to form coarser secondary carbides. This means that increasing the addition of Cr does not always lead to an increase in the hardness or wear resistance of the material. In addition, the wear resistance of 27Cr MWCI after tempering (wear rate: 8.80 × 10−5 g/m) is higher than that after quenching (wear rate: 9.25 × 10−5 g/m) owing to the increase in the fracture toughness of M7C3 carbide. This is contrary to the case of 18Cr-MWCI; the wear resistance after tempering (wear rate: 5.29 × 10−5 g/m) is worse than that after quenching (wear rate: 5.11 × 10−5 g/m) owing to the reduction in hardness as a stress-relieving effect.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Metal Alloys Wear and Properties · Advanced materials and composites · Orthopaedic implants and arthroplasty

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Muroran Institute of Technology, 27-1 Mizumoto, Muroran City 050-8585, Japan

Department of Mechanical Engineering, University of Sumatera Utara, Medan 20155, Indonesia

References (45)

Show source-provided references
1. Microstructure, hardness and abrasion of as-cast 17.5% Cr white irons
2. Abrasion resistant high-chromium white cast irons
3. Abrasive wear of white cast irons10.1016/0043-1648(80)90101-5 ↗
4. Influence of abrasive hardness on the wear resistance of high chromium irons10.1016/0043-1648(78)90113-8 ↗
5. Li, Y., Zhu, P.X., Tang, C., and Sun, Z. (2022). Effect of Quenching medium on microstructure and mechanical properties of high chromium cast iron. Crystals, 12.10.3390/cryst12101332 ↗
6. Microstructure modification of as-cast high chromium white cast iron by heat treatment10.1007/s11665-008-9285-6 ↗
7. Effect of heat treatment on the gouging abrasion resistance of alloy white cast iron10.1007/BF02664672 ↗
8. The effect of heat treatment on the abrasion resistance of alloy white cast irons10.1016/S0043-1648(96)07390-5 ↗
9. Wear and oxidation behaviour of high chromium white cast irons10.1016/j.matchar.2007.05.021 ↗
10. The influence of retained austenite in high chromium cast iron on impact-abrasive wear10.1016/0043-1648(90)90026-7 ↗
11. Application of rietveld refinement to investigate the high chromium white cast iron austempered at different temperatures10.1016/S1006-706X(09)60057-1 ↗
12. Influence of retained austenite on wear resistance of high chromium cast iron under various impact loads
13. The precipitation and transformation of secondary carbides in high chromium cast iron10.1016/j.matchar.2005.10.002 ↗
14. Secondary carbides in high chromium cast irons: An alternative approach to their morphological and spatial distribution characterization10.1016/j.matchar.2018.08.020 ↗
15. Effect of soaking temperature on carbide precipitation, hardness, and wear resistance of high chromium cast iron10.1007/s11668-020-00836-7 ↗
16. Microstructure and dry sliding wear resistance of CoTi intermetallic alloy10.1016/j.intermet.2008.06.010 ↗
17. Global energy consumption due to friction and wear in the mining industry10.1016/j.triboint.2017.05.010 ↗
18. Influence of addition of silicon, molybdenum, vanadium, and tungsten, upon the structural evaluation of as-cast state of a high-chromium cast iron (20%Cr, 2.6%C)
19. Influence of molybdenum and titanium on microstructure of Fe-C-Cr-Nb alloys white cast iron
20. Effect of Niobium on wear resistance of 15 % Cr white cast iron10.1016/0043-1648(93)90262-K ↗
21. Effect of tungsten on the microstructure and on the abrasive wear behavior of a high-chromium white cast iron
22. Effect of the simultaneous Ti and W addition on the microstructure and wear behavior of a high chromium white cast iron10.1051/metal/2019031 ↗
23. Solidification and abrasion wear of white cast irons alloyed with 20 % carbide forming elements10.1016/S0043-1648(01)00599-3 ↗
24. Abrasive wear characteristics of Fe-2C-5Cr-5Mo-5W-5Nb multi-component white cast iron10.1016/j.wear.2017.01.096 ↗
25. Effect of chromium content on three-boy-type abrasive wear behavior of multi-alloyed cast iron
26. Abrasive wear mechanism of multi-components ferrous alloys abraded by soft, fine abrasive particles10.1016/j.wear.2010.08.025 ↗
27. High erosion-oxidation performance of Fe-based Nb or V containing multicomponent alloys with Co addition at 1173 K10.1016/j.matdes.2015.08.161 ↗
28. High-temperature erosive wear characteristics and boding requirements of hard carbides cast-in insertion multi-component white cast iron10.1016/j.wear.2021.203672 ↗
29. Erosive wear characteristics of high-chromium based multi-component white cast irons10.1016/j.triboint.2021.106982 ↗
30. Rigney, D.A., and Gleaser, W.A. (1978). Wear characteristics of metals. Source Book on Wear Control Technology, American Society for Metals.
31. Microstructural evaluation and high-temperature erosion characteristic of high chromium cast irons10.1016/j.wear.2019.01.043 ↗
32. Microstructure and mechanical properties of a Mo alloyed high chromium cast iron after different heat treatments10.1016/j.vacuum.2018.07.013 ↗
33. The abrasive wear resistance of high chromium cast iron10.2478/afe-2014-0015 ↗
34. Abrasive wear behavior and mechanism of high chromium cast iron10.1016/S1006-706X(15)60014-0 ↗
35. Influence of Ni addition on erosive wear characteristics of multi-component white cast iron at elevated temperature10.1016/j.wear.2016.12.044 ↗
36. Abrasion resistance and fracture toughness of white cast irons10.1179/030716979803276228 ↗
37. Effect of (Fe, Cr)7C3 carbide orientation on abrasive wear resistance and fracture toughness10.1016/j.wear.2010.10.070 ↗
38. Classification of bulk metallic glasses by atoic size difference, heat of mixing and period of constituent elements and its application to characterization of the main alloying element10.2320/matertrans.46.2817 ↗
39. Improving the wear resistance of white cast iron using a new concept-high-entropy microstructure10.1016/j.wear.2010.12.029 ↗
40. Abrasive size and load effects on the wear of 19.9 % chromium and 2.9% carbon cast iron10.1016/j.wear.2017.02.008 ↗
41. (2010). Testing Method for Fracture Toughness of Fine Ceramics at Room Temperature (Standard No. JIS R 1607:2010).
42. Influence of Mo and W on high temperature hardness of M7C3 carbide in high chromium white cast iron
43. Effect of vanadium additive on structure property and tribological performance of high chromium cast iron hardfacing metal10.1016/j.surfcoat.2011.06.027 ↗
44. Beneficial effects of the core-shell structure of primary carbides in high-Cr (45 wt %) white cast irons on their mechanical behavior and wear resistance10.1007/s11249-015-0522-5 ↗
45. Formation mechanism of ultrafine M7C3 carbide in hypoeutectic Fe-25Cr-4C-0.5Ti-0.5Nb-0.2N-LaAlO3 hardfacing alloy layer10.1016/j.jmrt.2020.05.039 ↗