journal article·2025-05-14Open access

Influence of Homogenization Heat Treatments on the Mechanical, Structural, Biodegradation, and Cavitation Behavior of Some Alloys in the ZnMg(Fe) System

Brandușa Ghiban, Ilare Bordeasu, Aurora Antoniac, Iulian Antoniac, Cristina Maria Gheorghe, Dorin Bordeasu, Lavinia Madalina Micu, Cristian Ghera, Laura Cornelia Salcianu, Bogdan Florea, Daniel Ostoia, Anca Maria Fratila

Crystals· Volume 15· Issue 5

Abstract

This paper presents the biodegradation and cavitational erosion behavior of new zinc alloys in the ZnMgFe system. The alloys were heat-treated through homogenization at 300 °C and 400 °C, with maintenance times of 5 and 10 h each. The experimental research consisted of characterizing the structure and mechanical properties of the newly made alloys in different structural states, as well as determining their biodegradation and cavitation behavior. Biodegradability was achieved using laboratory tests in SBF, with different immersion durations (3, 7, 14, 21, or 35 days). The cavitation behavior was assessed by performing tests on a piezoceramic crystal vibrator in compliance with ASTM G32-2016, thus constructing the curves of the erosion velocity MDER(t) and the cumulative average erosion depth MDE(t). The analyses performed on the mechanical properties, microscopic images, and the cavitation parameters MDER and MDEmax (results at the end of the cavitation attack) showed the effect of the heat treatments on the structure and structural resistance to cyclic loadings of the cavitation. The double alloying of zinc with magnesium and iron may increase either the mechanical properties or the corrosion resistance to cavitation and can control the biodegradability of the resulting ZnMgFe alloy. The best heat treatment for improving these properties is homogenization at 400 °C/10 h, which may increase the cavitation erosion of zinc by up to seven times. The experimental results demonstrate that the new alloys from the ZnMgFe system are a good option for manufacturing biodegradable implants with functional in vitro properties.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Magnesium Alloys: Properties and Applications · Corrosion Behavior and Inhibition · Aluminum Alloys Composites Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Metallic Materials Science, Faculty of Materials Science and Engineering, National University of Science and Technology Politehnica Bucharest, 060042 Bucharest, Romania

Department of Mechanical Machinery, Equipment and Transport, Politehnica University of Timisoara, 1 Mihai Viteazu Boulevard, 300222 Timisoara, Romania

Department of Automation and Applied Informatics, Politehnica University of Timisoara, 2 Vasile Parvan Boulevard, 300223 Timisoara, Romania

Department of Agricultural Technologies-Department I, King Mihai I University of Life Sciences, 300645 Timișoara, Romania

Department of Mechatronics, Politehnica University of Timisoara, 1 Mihai Viteazu Boulevard, 300222 Timisoara, Romania

Department of Engineering and Management of Metallic Materials, Faculty of Materials Science and Engineering, National University of Science and Technology Politehnica Bucharest, 060042 Bucharest, Romania

Department of Dental Medicine and Nursing, Faculty of Medicine, Lucian Blaga University of Sibiu, 550169 Sibiu, Romania

References (42)

Show source-provided references
1. Recent metallic materials for biomedical applications10.1007/s11661-002-0109-2 ↗
2. Love, B.J. (2017). Biomaterials: A Systems Approach to Engineering Concepts, Academic Press. [1st ed.].
3. Electrochemical stability and corrosion resistance of Ti–Mo alloys for biomedical application10.1016/j.actbio.2008.07.010 ↗
4. Effects of chromium and nitrogen content on the microstructures and mechanical properties of as-cast Co–Cr–Mo alloys for dental applications10.1016/j.actbio.2012.03.024 ↗
5. Study of corrosion in biocompatible metals for implants: A review10.1016/j.jallcom.2017.01.196 ↗
6. A new look at biomedical Ti-based shape memory alloys10.1016/j.actbio.2012.01.018 ↗
7. Hermawan, H. (2012). Biodegradable Metals: From Concept to Applications, Springer Science & Business Media.10.1007/978-3-642-31170-3 ↗
8. Bioresorbable metals in cardiovascular stents: Material insights and progress10.1016/j.mtla.2020.100727 ↗
9. Research on an Mg–Zn alloy as a degradable biomaterial10.1016/j.actbio.2009.06.028 ↗
10. Antoniac, I., Miculescu, M., Mănescu, V., Stere, A., Quan, P.H., Păltânea, G., Robu, A., and Earar, K. (2022). Magnesium-Based Alloys Used in Orthopedic Surgery. Materials, 15.10.3390/ma15031148 ↗
11. In vitro degradation and cell viability assessment of Zn–3Mg alloy for biodegradable bone implants10.1177/0954411915584962 ↗
12. Kafri, A., Ovadia, S., Goldman, J., Drelich, J., and Aghion, E. (2018). The suitability of Zn-1.3%Fe alloy as a biodegradable implant material. Metals, 8.10.3390/met8030153 ↗
13. In vitro evaluation of the feasibility of commercial Zn alloys as biodegradable metals10.1016/j.jmst.2016.06.003 ↗
14. Investigation on the microstructure, mechanical properties, in vitro degradation behavior and biocompatibility of newly developed Zn-0.8%Li-(Mg, Ag) alloys for guided bone regeneration10.1016/j.msec.2019.01.120 ↗
15. Thermal characteristics, mechanical properties, in vitro degradation and cytotoxicity of novel biodegradable Zn–Al–Mg and Zn–Al–Mg–xBi alloys10.1007/s40195-017-0534-2 ↗
16. The influence of alloying and fabrication techniques on the mechanical properties, biodegradability and biocompatibility of zinc: A comprehensive review10.1016/j.actbio.2019.01.035 ↗
17. Biodegradable metallic bone implants10.1039/C8QM00507A ↗
18. Biodegradable Mg and Mg alloys: Corrosion and biocompatibility10.1016/j.mseb.2011.05.028 ↗
19. Levy, G., Goldman, J., and Aghion, E. (2017). The prospects of zinc as a structural material for biodegradable implants-a review paper. Metals, 7.10.3390/met7100402 ↗
20. Experimental determination of phase diagram in the Zn-Fe binary system10.1016/j.jallcom.2017.11.320 ↗
21. In vitro cytocompatibility, hemocompatibility and antibacterial properties of biodegradable Zn-Cu-Fe alloys for cardiovascular stents applications10.1016/j.msec.2020.111007 ↗
22. Microstructure, mechanical properties and in vitro degradation behavior of novel Zn-Cu-Fe alloys10.1016/j.matchar.2017.10.015 ↗
23. Enhance-ment in mechanical and corrosion resistance properties of a biodegradable Zn-Fe alloy through second phase refinement10.1016/j.msec.2020.111197 ↗
24. Highly ductile Zn-2Fe-WC nanocomposite as biodegradable10.1007/s11661-020-05878-y ↗
25. (2016). Standard Method of Vibratory Cavitation Erosion Test (Standard No. ASTM, Standard G32).
26. Bordeasu, I. (2020). Monografia Laboratorului de Cercetare a Eroziunii prin Cavitatie al Universitatii Politehnica Timisoara (1960–2020), Editura Politehnica.
27. Cavitation Erosion Mechanisms of Solution Treated X5CrNi18-10 Stainless Steels10.1115/1.4032489 ↗
28. Bordeasu, I., Ghera, C., Luca, A.-N., Manea, A.-S., Stroita, D.-C., Salcianu, L.C., Ghiban, B., and Micu, L.M. (2024). Investigation of Cavitation Resistance of Biocompatible Zinc-Based Alloys for Biomedical Applications. International Conference on Machine and Industrial Design in Mechanical Engineering, Springer Nature.10.1007/978-3-031-80512-7_26 ↗
29. New contributions to cavitation erosion curves modeling
30. Research of the Cavitation Resistance of a Biodegradable Alloy Zn-Cu
31. Cavitational Erosion Behavior of a Biodegradable Alloy from the Zn-Mg System for Biomedical Applications10.24874/ti.1604.11.23.01 ↗
32. Hydroxyapatite Coatings on Mg-Ca Alloy Prepared by Pulsed Laser Deposition: Properties and Corrosion Resistance in Simulated Body Fluid10.1016/j.ceramint.2018.06.095 ↗
33. Iordache (Gheorghe), C.M. (2024). Correlation Between Structure-Mechanical Characteristics-Biodegradability- Cavitation of Some Biomedical Alloys form the System ZnMg(Fe). [Ph.D. Thesis, National University of Science and Technology Politehnica Bucharest]. (in Romanian).
34. Ciungu, G. (2024). Experimental Studies on the Cavitation and Biodegradation Behaviour of Some Alloys of the System ZnCu(Mg) System. [Ph.D. Thesis, University Politehnica Bucharest].
35. Ghiban, B., Antoniac, A., Bordeasu, I., Antoniac, I., Petre, G., Rau, J., Bordeasu, D., and Micu, L.M. (2025). Biodegradability and Cavitation Erosion Behavior of Some Zinc Alloys from the System ZnCuMg. Metals, 15.10.3390/met15020161 ↗
36. Cerbu, C., Ursache, S., Botis, M.F., and Hadar, A. (2021). Simulation of the Hybrid Carbon-Aramid Composite Materials Based on Mechanical Characterization by Digital Image Correlation Method. Polymers, 13.10.3390/polym13234184 ↗
37. Ursache, S., Cerbu, C., and Hadar, A. (2024). Characteristics of Carbon and Kevlar Fibres, Their Composites and Structural Applications in Civil Engineering-A Review. Polymers, 16.10.3390/polym16010127 ↗
38. Determination through numerical computation of the designed and functional parameters of ultra acustic systems for ultrasonic welding of intelligent composite materials, 2007
39. Finite Element Analysis of the Multilayered Honeycomb Composite Material Subjected to Impact Loading10.37358/MP.17.1.4812 ↗
40. (1960). Experience with a 20—KC Cavitations Erosion Test, Erosion by Cavitations or Impingement (Standard No. ASTM STP 408).
41. (1966). Corelation of Cavitation Damage with Other Material and Fluid Properties, Erosion by Cavitation or Impingement (Standard No. ASTM STP 408).
42. Franc, J.P., Kueny, J.L., Karimi, A., Fruman, D.H., Fréchou, D., Briançon-Marjollet, L., Yves Billard, J.Y., Belahadji, B., Avellan, F., and Michel, J.M. (1995). La Cavitation. Mécanismes Physiques et Aspects Industriels, Press Universitaires de Grenoble.