journal article·2020-04-01Open access

Optimized Corrosion Performance of AISI 1345 Steel in Hydrochloric Acid Through Thermo-Mechanical Cyclic Annealing Processes

Muhammad Arslan Hafeez, Aqil Inam, Misbah Ul Hassan, Malik Adeel Umer, Muhammad Usman, Asad Hanif

Crystals· Volume 10· Issue 4

Abstract

The thermo-mechanical treatments and cyclic annealing processes have the potential of optimizing the corrosion performance of carbon steels in corrosive environments. Herein, an attempt has been made to optimize the corrosion performance of AISI 1345 steel in hydrochloric acid by thermo-mechanical cyclic annealing treatments. AISI 1345 steel was produced and cast in the laboratory and subjected to three types of thermo-mechanical cyclic annealing treatments (TMCA). The first TMCA treatment comprised hot rolling at 1050 °C followed by oil quenching and single austenitizing at 900 °C followed by furnace cooling (TMSA). The second and the third TMCA treatments involved similar hot rolling processes with double austenitizing and furnace cooling (TMDA) and triple austenitizing and furnace cooling (TMTA) processes. Microstructure analysis showed that dual-phase (retained austenite + pearlite) microstructure was achieved after all TMCA treatments with an exception of secondary phase particles precipitation after TMSA treatment. Maximum fractions of retained austenite and minimum fractions of pearlite were achieved after TMTA treatment. Highly refined microstructure of size 26.7 µm was achieved after TMDA treatment whereas; TMSA treatment offered coarse grained microstructure of size 254 µm. Electrochemical analysis was performed in 5 vol% HCl solution using Tafel scan technique. Results revealed that both TMDA and TMTA treatments caused three-fold reduction in corrosion rates (3.025, 2.771 mpy) compared to non-treated steel sample. After 168 h of immersion corrosion analysis in 5 vol% HCl solution, the surface of TMTA treated sample was observed to be partially covered with a very thin, crack-free oxide layer exhibiting minimum oxygen (8.16%) percentage. These features indicated that the TMTA treated sample underwent a very low-intensity minor corrosion attack of HCl solution and exhibited the best immersion corrosion performance among all samples. Electrochemical and immersion corrosion analysis results were in good agreement.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Hydrogen embrittlement and corrosion behaviors in metals · Corrosion Behavior and Inhibition · High-Temperature Coating Behaviors

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

School of Civil and Environmental Engineering, National University of Science and Technology, Islamabad 44000, Pakistan

Department of Metallurgy and Materials Engineering, CEET, University of the Punjab, Lahore 54590, Pakistan

School of Chemical and Materials Engineering, National University of Science and Technology, Islamabad 44000, Pakistan

Institute of Applied Physics and Materials Engineering, University of Macau, Avenida da Universidade, Taipa, Macau S.A.R 999078, China

References (58)

Show source-provided references
1. Insights into corrosion inhibition behavior of a triazole derivative for mild steel in hydrochloric acid solution10.1016/j.matpr.2019.04.066 ↗
2. Towards a deeper understanding of the inhibition mechanism of a new 1,2,3-triazole derivative for mild steel corrosion in the hydrochloric acid solution using coupled experimental and theoretical methods10.1016/j.matchemphys.2019.122420 ↗
3. Sargassum muticum extract based on alginate biopolymer as a newefficient biological corrosion inhibitor for carbon steel in hydrochloric acid pickling environment: Gravimetric, electrochemical and surface studies10.1016/j.ijbiomac.2019.08.253 ↗
4. Bouhlal, F., Labjar, N., Abdoun, F., Mazkour, A., Idrissi, M.S., Mahi, M.E., Lotfi, E.M., Skalli, A., and Hajjaji, S.E. (2019). Chemical and electrochemical studies of the inhibition performance ofhydro-alcoholic extract of used coffee grounds (HECG) for the corrosion of C38 steel in 1 M hydrochloric acid. Egypt. J. Pet.10.1155/2020/4045802 ↗
5. Synthesis and characterization of a novel organic corrosion inhibitor for mild steel in 1 M hydrochloric acid10.1016/j.rinp.2017.12.039 ↗
6. A high-efficiency corrosion inhibitor of N-doped citric acid-based carbon dots for mild steel in hydrochloric acid environment10.1016/j.jhazmat.2019.121019 ↗
7. Exploring the potential role of pyrazoline derivatives in corrosion inhibition of mild steel in hydrochloric acid solution: Insights from experimental and computational studies10.1016/j.conbuildmat.2019.117320 ↗
8. A novel green inhibitor for C-steel corrosion in 2.0 mol·L−1 hydrochloric acid solution10.1016/j.cjche.2016.08.017 ↗
9. Corrosion behaviour of metal complexes of antipyrine based azo dye ligand for soft-cast steel in 1 M hydrochloric acid10.1016/j.jksus.2019.04.007 ↗
10. corrosion inhibition of mild steel in 1M hydrochloric acid using haematostaphisbarteri leaves extract10.1016/j.promfg.2019.06.088 ↗
11. Optimized corrosion performance of a carbon steel in dilute sulfuric acid through heat treatment10.1016/j.apsusc.2019.06.180 ↗
12. The effects of stabilizing treatment on microstructure and corrosion resistance of 316Ti stainless steel10.1016/j.engfailanal.2019.07.047 ↗
13. Mechanical properties and corrosion behavior of selective laser melted 316L stainless steel after different heat treatment processes10.1016/j.jmst.2019.03.003 ↗
14. Effects of heat treatment on microstructure, mechanical and corrosion properties of 15-5 PH stainless steel parts built by selective laser melting process10.1016/j.jmapro.2019.12.048 ↗
15. Study on Corrosion Behavior of Heat Treated High Carbon Low Alloy Steel10.1016/j.matpr.2017.11.648 ↗
16. Effect of heat treatment on microstructure, mechanical and corrosion properties of austenitic stainless steel 316 L using arc additive manufacturing10.1016/j.msea.2017.10.002 ↗
17. Microstructure evolution and electrochemical corrosion behaviour of API X70 linepipe steel in different environments10.1016/j.ijpvp.2019.01.013 ↗
18. Effect of tempering heat treatment on the CO2 corrosion resistance of quench-hardened Cr-Mo low-alloy steels for oil and gas applications10.1016/j.corsci.2019.03.036 ↗
19. An electrochemical study on the effect of stabilization and sensitization heat treatments on the intergranular corrosion behaviour of AISI 321H austenitic stainless steel10.1016/j.corsci.2018.03.043 ↗
20. Influence of the aging time on the microstructure and electrochemical behaviour of a 15-5PH ultra-high strength stainless steel10.1016/j.corsci.2018.04.032 ↗
21. Enhancing the corrosion resistance of selective laser melted 15-5PH martensite stainless steel via heat treatment10.1016/j.corsci.2019.108427 ↗
22. Microstructural and electrochemical characterisation of heat-treated 347 stainless steel with different phases10.1016/j.corsci.2012.10.011 ↗
23. Effectiveness of an intercritical heat-treatment on localized corrosion resistance at the microstructural boundaries of medium-carbon steel10.1016/j.corsci.2019.04.019 ↗
24. Enhancement of intergranular corrosion resistance of type 304 stainless steel through a novel surface thermo-mechanical treatment10.1016/j.surfcoat.2013.06.124 ↗
25. Mechanical and corrosion properties of medium carbon low alloy steel after cyclic quenching and tempering heat–treatments10.1088/2053-1591/ab6581 ↗
26. Effect of thermo-mechanical treatment on tensile properties of reduced activation ferritic-martensitic steel10.1016/j.msea.2018.03.080 ↗
27. Effect of thermo-mechanical treatment on microstructure and mechanical properties of P92 heat resistant steel10.1016/j.msea.2012.09.040 ↗
28. Tensile and impact behaviour of thermo mechanically treated and micro-alloyed medium carbon steel bar10.1016/j.conbuildmat.2018.10.098 ↗
29. Effect of single and double austenitization treatments on the microstructure and mechanical properties of 16Cr-2Ni Steel10.1361/105994999770346963 ↗
30. The effects of double austenitization on the mechanical properties of a 0.34C containing low-alloy Ni-Cr-Mo-V steel10.1007/BF02651596 ↗
31. Study on effect of double austenitization treatment on fracture morphology tensile tested nuclear grade P92 steel10.1016/j.engfailanal.2018.09.036 ↗
32. Effect of single and double austenitization treatments on the microstructure and hardness of AISI D2 tool steel10.1016/j.matpr.2015.07.145 ↗
33. Effects of double quenching on fatigue properties of high carbon bearing steel with extra-high purity10.1016/j.ijfatigue.2019.06.036 ↗
34. Effects of Ti and a twice-quenching treatment on the microstructure and ductile brittle transition temperature of 9CrWVTiN steels10.1016/j.matdes.2015.09.056 ↗
35. Evolution of microstructure and mechanical properties of medium Mn steels during double annealing10.1016/j.msea.2012.02.024 ↗
36. Structure and texture formation during single and double cold rolling and annealing processes for Nb+Ti added interstitial-free steels10.1016/S1006-706X(13)60096-5 ↗
37. Fabrication of bimodal-grained Al-free medium Mn steel by double intercritical annealing and its tensile properties10.1016/j.jallcom.2016.04.014 ↗
38. Attaining deep drawability and non-earing properties in Ti + Nb interstitial-free steels through double cold rolling and annealing10.1016/j.scriptamat.2007.03.055 ↗
39. Formation of nano-grained structure in a 301 stainless steel using a repetitive thermo-mechanical treatment10.1016/j.matlet.2009.03.043 ↗
40. Tensile flow and work hardening behavior of reduced activation ferritic martensitic steel subjected to thermo-mechanical treatment10.1016/j.jnucmat.2019.04.009 ↗
41. Microstructural, mechanical and tribological investigation of 30CrMnSiNi2A ultra-high strength steel under various tempering temperatures10.1088/2053-1591/aa9fd3 ↗
42. Effect of microstructural transformation during tempering on mechanical properties of quenched and tempered 38CrSi steel10.1088/2053-1591/ab1db9 ↗
43. Investigation on microstructural, mechanical, and electrochemical properties of water, brine quenched and tempered low carbon steel10.1088/2053-1591/ab2c7f ↗
44. Effect of tempering time on microstructure, mechanical, and electrochemical properties of quenched–partitioned–tempered Advanced High Strength Steel (AHSS)10.1088/2053-1591/ab52b7 ↗
45. Roberge, P.R. (2000). Handbook of Corrosion Engineering, McGraw-Hill.
46. Revie, R.W., and Uhlig, H.H. (2008). Corrosion and Corrosion Control, John Wiley and Sons Inc.. [4th ed.].10.1002/9780470277270 ↗
47. Effect of heat treatments on the mechanical and electrochemical behavior of 38CrSi and AISI 4140 steels10.1007/s13632-019-00556-x ↗
48. Hafeez, M.A. (2020). Mechanical investigation on mechanical properties and immersion corrosion performance of 0.35%C–10.5%Mn steel processed by austenite reverted transformation (ART) annealing process. Metallogr. Microstruct. Anal., 1–10.10.1007/s13632-020-00629-2 ↗
49. Accumulation of arsenic in drinking water distribution systems10.1021/es049850v ↗
50. Iron release from corroded iron pipes in drinking water distribution systems: Effect of dissolved oxygen10.1016/j.watres.2003.11.022 ↗
51. Physiochemical characterization of five iron tubercles from a single drinking water distribution system: Possible new insights on their formation and growth10.1016/j.corsci.2008.05.005 ↗
52. Characterization of elemental and structural composition of corrosion scales and deposits formed in drinking water distribution systems10.1016/j.watres.2010.05.043 ↗
53. Characteristics of iron corrosion scales and water quality variations in drinking water distribution systems of different pipe materials10.1016/j.watres.2016.10.044 ↗
54. Physico-chemical characteristics of corrosion scales in old iron pipes10.1016/S0043-1354(00)00591-1 ↗
55. Characterization of corrosion products formed on steels in the first months of atmospheric exposure10.1590/S1516-14392003000300015 ↗
56. Carburisation of ferritic Fe-Cralloys by low carbon activity gases10.1016/j.corsci.2011.05.013 ↗
57. In situ Raman spectroscopic investigation of chromium surfaces under hydrothermal conditions10.1016/S0169-4332(01)00338-5 ↗
58. Morphological and physicochemical characteristics of iron corrosion scales formed under different water source histories in a drinking water distribution system10.1016/j.watres.2012.07.031 ↗