journal article·2021-01-26Open access

The Effect of Heat Treatment on Dynamic Properties of an Additively Manufactured Ti-6Al-4V Alloy

Shuangyin Zhang, Yunfei Wang, Tao Suo, Jin Yao, Xin Lin, Weidong Huang, Yulong Li, Jianghua Shen

Crystals· Volume 11· Issue 2

Abstract

Heat treatment processing is commonly applied for additively manufactured metal materials, since the as-fabricated material frequently exhibits high internal stress and self-cracking. In this work, a heat treatment route was applied to an additively manufactured Ti-6Al-4V alloy, and its effect on the dynamic compressive behavior was investigated. The experimental results showed that the heat treatment process not only increased the dynamic compressive strength of the material, but also induced a change of the dynamic compressive strength from isotropic to anisotropic. In addition, the strain rate sensitivity of the material was reduced by heat treatment, even though both the as-deposited and heat-treated samples demonstrated positive sensitivity to the loading rate. Microstructural analysis suggested that the grain size and morphology were the same before and after heat treatment, while the internal stress increased due to heat treatment.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Additive Manufacturing Materials and Processes · Additive Manufacturing and 3D Printing Technologies · Titanium Alloys Microstructure and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

School of Aeronautics, Northwestern Polytechnical University, Xi’an 710072, China

Shaanxi Key Laboratory of Impact Dynamic and Its Engineering Application, Northwestern Polytechnical University, Xi’an 710072, China

The State Key Laboratory of Solidification Processing, Northwestern Polytechnical University, Xi’an 710072, China

School of Civil Aviation, Northwestern Polytechnical University, Xi’an 710072, China

Funding

National Natural Science Foundation of China · Fundamental Research Funds for the Central Universities

References (21)

Show source-provided references
1. Laser additive manufacturing of metallic components: Materials, processes and mechanisms10.1179/1743280411Y.0000000014 ↗
2. Metal Additive Manufacturing: A Review10.1007/s11665-014-0958-z ↗
3. Additive manufacturing of metallic components—Process, structure and properties10.1016/j.pmatsci.2017.10.001 ↗
4. Influence of Heat Treatment on the Microstructure and Properties of Ti-6Al-4V Titanium Alloy by Laser Rapid Forming
5. Quasi-static and high strain rate fracture behaviour of Ti6Al4V10.1016/j.ijimpeng.2017.03.001 ↗
6. High-strain-rate plastic deformation and fracture behaviour of Ti-5Al-5Mo-5V-1Cr-1Fe titanium alloy at room temperature10.1016/j.mechmat.2017.08.007 ↗
7. Adiabatic shear behaviors in rolled and annealed pure titanium subjected to dynamic impact loading10.1016/j.msea.2017.01.011 ↗
8. Strain rate dependence of deformation-induced transformation and twinning in a metastable titanium alloy10.1016/j.actamat.2015.11.026 ↗
9. Rate-dependent hardening model for pure titanium considering the effect of deformation twinning10.1016/j.ijmecsci.2015.04.008 ↗
10. Rate-dependent hardening due to twinning in an ultrafine-grained magnesium alloy10.1016/j.actamat.2011.12.002 ↗
11. Nucleation and growth of twins in Zr: A statistical study10.1016/j.actamat.2009.08.030 ↗
12. Strength and strain hardening of a selective laser melted AlSi10Mg alloy10.1016/j.scriptamat.2017.07.025 ↗
13. Microstructure and anisotropic tensile behavior of laser additive manufactured TC21 titanium alloy10.1016/j.msea.2016.07.040 ↗
14. Review on manufacture by selective laser melting and properties of titanium based materials for biomedical applications10.1179/1753555715Y.0000000076 ↗
15. Additive manufacturing of strong and ductile Ti–6Al–4V by selective laser melting via in situ martensite decomposition10.1016/j.actamat.2014.11.028 ↗
16. Moebus, G., Walther, T., Brydson, R., Ozkaya, D., MacLaren, I., Donnelly, S., Nellist, P., Li, Z., Baker, R., and Chiu, Y.L. (2011, January 6–9). Microstructure of Ti-6Al-4V produced by selective laser melting. Proceedings of the Electron Microscopy and Analysis Group Conference 2011, Birmingham, UK.
17. Microstructure evolution and mechanical behavior of ultrafine Tie6Ale4V during low-temperature superplastic deformation10.1016/j.actamat.2016.09.003 ↗
18. Quench rates in air, water, and liquid nitrogen, and inference of temperature in volcanic eruption columns10.1016/S0012-821X(02)00656-8 ↗
19. Investigations on the effect of heating temperature and cooling rate on evolution of microstructure in an α + β titanium alloy10.1557/jmr.2018.54 ↗
20. Effect of Temperature and Cooling Rates on the α+β Morphology of Ti-6Al-4V Alloy10.1016/j.prostr.2019.07.056 ↗
21. Rate sensitivity and work-hardening behavior of an advanced Ti-Al-N alloy under uniaxial tensile loading10.1016/j.msea.2018.12.066 ↗