journal article·2025-05-26Open access

Effect of Deposits on Micron Particle Collision and Deposition in Cooling Duct of Turbine Blades

Shihong Xin, Chuqi Peng, Junchao Qi, Baiwan Su, Yan Xiao

Crystals· Volume 15· Issue 6

Abstract

Aerospace engines ingest small particles when operating in a particulate-rich environment, such as sandstorms, atmospheric pollution, and volcanic ash clouds. These micron particles enter their cooling channels, leading to film-cooling hole blockage and thus thermal damage to turbine blades made of nickel-based single-crystal superalloy materials. This work studied the collision and deposition mechanisms between the micron particles and structure surface. A combined theoretical and numerical study was conducted to investigate the effect of deposits on particle collision and deposition. Finite element models of deposits with flat and rough surfaces were generated and analyzed for comparison. The results show that the normal restitution coefficient is much lower when a micron particle impacts a deposit compared to that of particle collisions with DD3 nickel-based single-crystal wall surfaces. The critical deposition velocity of a micron particle is much higher for particle–deposit collisions than for particle–wall collision. The critical deposition velocity decreases with the increase in particle size. When micron particles deposit on the wall surface of the structure, early-stage particle–wall collision becomes particle–deposit collision when the height of the deposits is greater than twice the particle diameter. For contact between particles and rough surface deposits, surfaces with a shorter correlation length, representing a higher density of asperities and a steeper surface, have a much longer contact time but a lower contact area. The coefficient of restitution of the particle reduces as the surface roughness of the deposits increase. The characteristic length of the roughness has little effect on the rebounding rotation velocity of the particle.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Turbomachinery Performance and Optimization · Particle Dynamics in Fluid Flows · Heat Transfer Mechanisms

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Engineering Mechanics, Henan University of Science and Technology, Luoyang 471000, China

Particulate and Multiphase Flow Science International Joint Laboratory of Henan Province, Luoyang 471000, China

LuoYang Bearing Research Institute Co., Ltd., Luoyang 471000, China

Office of Educational Administration, Henan University of Science and Technology, Luoyang 471000, China

Funding

Key Research & Development and Promotion Projects of Henan Province

References (36)

Show source-provided references
1. Liu, D., Ding, Q., Zhou, Q., Zhou, D., Wei, X., Zhao, X., Zhang, Z., and Bei, H. (2023). Microstructure, Mechanical Properties and Thermal Stability of Ni-Based Single Crystal Superalloys with Low Specific Weight. Crystals, 13.10.3390/cryst13040610 ↗
2. Wylie, S., Bucknell, A., Forsyth, P., McGilvray, M., and Gillespie, D.R. (2017). Reduction in flow parameter resulting from volcanic ash deposition in engine representative cooling passages. J. Turbomach., 139.10.1115/1.4034939 ↗
3. Boulanger, A., Patel, H., Hutchinson, J., DeShong, W., Xu, W., Ng, W., and Ekkad, S. (2016). Preliminary experimental investigation of initial onset of sand deposition in the turbine section of gas turbines. Turbo Expo: Power for Land, Sea, and Air, American Society of Mechanical Engineers. GT2016-56059.10.1115/GT2016-56059 ↗
4. Evolution of surface deposits on a high pressure turbine blade, part i: Physical characteristics
5. Experimental study on deposition of particulate on plate surface with cooling film
6. Lundgreen, R., Sacco, C., Prenter, R., and Bons, J.P. (2016). Temperature effects on nozzle guide vane deposition in a new turbine cascade rig. Turbo Expo: Power for Land, Sea, and Air, American Society of Mechanical Engineers. GT2016-57560.10.1115/GT2016-57560 ↗
7. Davidson, F.T., Kistenmacher, D.A., and Bogard, D.G. (2014). A Study of Deposition on a Turbine Vane With a Thermal Barrier Coating and Various Film Cooling Geometries. J. Turbomach., 136.10.1115/1.4026613 ↗
8. Laycock, R., and Fletcher, T.H. (2016). Independent effects of surface and gas temperature on coal fly ash deposition in gas turbines at temperatures up to 1400 °C. J. Eng. Gas Turbines Power, 138.10.1115/1.4031318 ↗
9. Lawson, S.A., Lynch, S.P., and Thole, K.A. (2013). Simulations of multiphase particle deposition on a non-axisymmetric contoured end wall with film-cooling. J. Turbomach., 135.10.1115/1.4007598 ↗
10. Albert, J.E., and Bogard, D.G. (2012). Experimental simulation of contaminant deposition on a film cooled turbine air-foil leading edge. J. Turbomach., 134.10.1115/1.4003964 ↗
11. Albert, J.E., and Bogard, D.G. (2013). Experimental simulation of contaminant deposition on a film-cooled turbine vane pressure side with a trench. J. Turbomach., 135.10.1115/1.4007821 ↗
12. Simulation of surface deposits of micron sand particles in the internal cooling duct with a Gaussian probability density model10.1007/s40571-024-00731-0 ↗
13. A mathematical model of the impact and adhesion of microspheres10.1080/02786829208959537 ↗
14. Tafti, D., and Sreedharan, S. (2010, January 14–18). Composition dependent model for the prediction of syngas ash deposition with application to a leading edge turbine vane. Proceedings of the ASME Turbo Expo, 2010, GT2010-23655, Glasgow, UK.
15. Particle deposition model for particulate flows at high temperatures in gas turbine components10.1016/j.ijheatfluidflow.2014.11.008 ↗
16. Impact model for micrometer-sized sand particles10.1016/j.powtec.2016.02.014 ↗
17. An impulse based model for spherical particle collisions with sliding and rolling10.1016/j.powtec.2017.06.049 ↗
18. Yu, K., and Tafti, D. (2019). Size and temperature dependent collision and deposition model for micron-sized sand particles. J. Turbomach. -Trans. ASME, 141.10.1115/1.4042215 ↗
19. Dowd, C., Tafti, D., and Yu, K. (2017). Sand transport and deposition in rotating two-passed ribbed duct with Coriolis and centrifugal Buoyancy forces at RE=100,000. Turbo Expo: Turbomachinery Technical Conference and Exposition, American Society of Mechanical Engineers. GT2017-63167.10.1115/GT2017-63167 ↗
20. Dust transport investigation in ribbed cooling duct integrating temperature-dependent elastic-plastic particle collision model
21. Forsyth, P.R., Gillespie, D.R., and McGilvray, M. (2018). Development and applications of a couple deposition dynamic mesh morphing approach for the numerical simulation of gas turbine flows. J. Eng. Gas Turbines Power Trans. ASME, 140.10.1115/1.4037825 ↗
22. Unsteady CFD simulation on ash particle deposition and removal characteristics in tube banks: Focusing on particle diameter, flow velocity, and temperature10.1016/j.joei.2020.01.010 ↗
23. Three-dimensional motion of particles in a shear flow near a rough wall10.1016/j.jaerosci.2015.10.004 ↗
24. Small particle adhesion: Measurement and control10.1016/S0927-7757(99)00442-2 ↗
25. Contact of nominally flat surfaces
26. Effects of interfacial strength and roughness on the static friction coefficient10.1007/s11249-014-0414-0 ↗
27. Influence of the surface roughness on the collision behavior of fine particles in ambient fluids10.1016/j.powtec.2021.06.051 ↗
28. Rajupet, S., Riet, A.A., Chen, Q., Sow, M., and Lacks, D.J. (2021). Relative importance of electrostatic and van der Waals forces in particle adhesion to rough conducting surfaces. Phys. Rev. E, 103.10.1103/PhysRevE.103.042906 ↗
29. Wang, Y., Zhang, Y., Fang, Z., and Wu, X. (2024). The effect of surface roughness on the viscoelastic energy dissipation in a particle-wall collision. J. Aerosol Sci., 175.10.1016/j.jaerosci.2023.106280 ↗
30. Elastic-plastic contact of a rough surface with weierstrass profile
31. A statistical model of elasto-plastic asperity contact between rough surfaces10.1016/j.triboint.2005.09.001 ↗
32. Yu, K., Peng, C., Shang, L., and Tafti, D. (2024). Elastic-plastic collision mechanism of micron-sized particle impacting rough surfaces. Powder Technol., 442.10.1016/j.powtec.2024.119903 ↗
33. Liu, J., Yu, K., Tafti, D., Yang, X., and Xu, H. (2023). Dust adhesion and deposition behavior in internal cooling duct with pin fins. Int. J. Therm. Sci., 184.10.1016/j.ijthermalsci.2022.107943 ↗
34. Energy dissipation during normal impact of elastic and elastic–plastic spheres10.1016/j.ijimpeng.2005.08.007 ↗
35. A facile method for simulating randomly rough membrane surface associated with interface behaviors10.1016/j.apsusc.2017.08.013 ↗
36. The effect of surface roughness on normal restitution coefficient, adhesion force and friction coefficient of the particle-wall collision10.1016/j.powtec.2019.11.120 ↗