journal article·2024-06-17Open access

Application of Organo-Modified Silica Nanoparticles to Improve the Load-Bearing Capacity of Bonded Joints of Dissimilar Steel Substrates

Anna Guzanová, Dagmar Draganovská, Miroslav Tomáš, Petr Szelag, Nikita Veligotskyi, Miroslav Džupon, Marek Vojtko

Crystals· Volume 14· Issue 6

Abstract

The paper deals with the joining of dissimilar steels by adhesive bonding. The base materials for the experimental work were deep-drawn low-carbon steel DC04, and hot-dip galvanized HSLA steel HX340LAD+Z. Adhesive bonding was performed using rubber-based and epoxy-based adhesives. The research aimed to verify the importance of surface preparation of steel substrates using a formulation with organically modified silica nanoparticles and epoxy organic functional groups, where one end of the functional group can be incorporated into the organic binder of the coating material and the other end can be firmly bonded to substances of an inorganic nature (metals). Since the binder base of adhesives is very similar to that of coatings, verifying the performance of this surface preparation when interacting with the adhesive is necessary. The load-bearing tensile shear capacity of single-lapped joints and the resistance of the joints against corrosion-induced disbanding in a climate chamber were tested. The energy dissipated by the joints up to fracture was calculated from the load-displacement curves. Bonded joints with organosilane were compared with joints without surface preparation and joints prepared by chroman-free zirconate passivation treatment. Exposure of the joints in the climatic chamber did not cause a relevant reduction in the characteristics of the joints. Organosilicate formulation was proved effective when bonding ungalvanized steels with a rubber-based structural adhesive, where it improves the bond quality between the adhesive and the substrate.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Tribology and Wear Analysis · Metal and Thin Film Mechanics · Material Properties and Applications

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Technology, Materials and Computer Supported Production, Faculty of Mechanical Engineering, Technical University of Košice, Mäsiarska 74, 040 01 Košice, Slovakia

Department of Automotive Production, Faculty of Mechanical Engineering, Technical University of Košice, Mäsiarska 74, 040 01 Košice, Slovakia

Pragochema spol. s.r.o., Přátelství 550, 104 00 Prague 10—Uhříněves, Czech Republic

Institute of Materials Research, Slovak Academy of Sciences, Watsonova 1935/47, 040 01 Košice, Slovakia

Funding

Research on the applicability of thermal drilling technology for the creation of multi-material joints in the automotive industry · Innovation of the educational process by implementing adaptive hypermedia systems in the teaching of subjects in the field of coating technology and welding of materials · Innovative approaches in the reconstruction of functional surfaces by laser cladding

References (34)

Show source-provided references
1. Effect of base steels on mechanical behavior of adhesive joints with dissimilar steel substrates10.1016/j.ijadhadh.2014.02.010 ↗
2. Lamberti, M., Maurel-Pantel, A., and Lebon, F. (2023). Mechanical Performance of Adhesive Connections in Structural Applications. Materials, 16.10.3390/ma16227066 ↗
3. Luo, J., Liu, J., Xia, H., Ao, X., Yin, H., and Guo, L. (2023). Surface Treatments for Enhancing the Bonding Strength of Aluminum Alloy Joints. Materials, 16.10.3390/ma16165674 ↗
4. Guzanová, A., Draganovská, D., Brezinová, J., Tomáš, M., Veligotskyi, N., and Kender, Š. (2024). Hybrid Joining of Dissimilar Thin Metallic Sheets—Mechanical Joining and Adhesive Bonding. Crystals, 14.10.3390/cryst14030220 ↗
5. Guzanová, A., Brezinová, J., Varga, J., Džupon, M., Vojtko, M., Janoško, E., Viňáš, J., Draganovská, D., and Hašuľ, J. (2023). Experimental study of steel–aluminum joints made by RSW with insert element and adhesive bondings. Materials, 16.10.3390/ma16020864 ↗
6. Messler, R.W. (2004). Joining of Materials and Structures: From Pragmatic Process to Enabling Technology, Elsevier Inc.. [1st ed.].
7. Messler, R.W. (1993). Joining of Advanced Materials, Elsevier Inc.. [1st ed.].
8. Joining sheet panels to thin-walled tubular profiles by tube end forming10.1016/j.jclepro.2010.12.014 ↗
9. Schmerler, R., and Rothe, F. (2019, September 10). Hybrid Joining Using the Flow Drill Technology. Germany. Available online: https://www.researchgate.net/publication/341616091_Hybridfugen_durch_Fliesslochformen_Hybrid_joining_using_the_flow_drill_technology#fullTextFileContent.
10. Multi-material adhesive joints for automotive industry10.1016/j.compositesb.2018.06.009 ↗
11. Joint strength optimization by the mixed-adhesive technique10.1016/j.ijadhadh.2008.09.009 ↗
12. Monitoring of changes in the roughness of the metal surface after the application of the conversion layer
13. Simple and rapid method for restoring anti-adhesive organosilane coatings on metal substrates10.1016/j.porgcoat.2019.105490 ↗
14. Superhydrophobic surface containing cerium salt and organosilane for corrosion protection of galvanised steel10.1016/j.jallcom.2020.153921 ↗
15. Well-organized organosilane composites for adhesion enhancement of heterojunctions10.1016/j.compscitech.2020.108135 ↗
16. Mutual intercropping-inspired co-silanization to graft well-oriented organosilane as adhesion promotion nanolayer for flexible conductors10.1016/j.jiec.2019.11.017 ↗
17. Optimization study of hybrid spot-welded/bonded single-lap joints10.1016/j.ijadhadh.2012.01.018 ↗
18. Adhesive selection for hybrid spot-welded/bonded single-lap joints: Experimentation and numerical analysis10.1016/j.compositesb.2015.09.002 ↗
19. Debonding on command of adhesive joints for the automotive industry10.1016/j.ijadhadh.2015.01.014 ↗
20. Organosilanes as adhesion promoters
21. The interaction of a commercial dry film adhesive with aluminium and organosilane treated aluminium surfaces: A study by XPS and ToF-SIMS10.1016/S0143-7496(01)00056-2 ↗
22. Interfacial chemistry of adhesives on hydrated aluminium and hydrated aluminium treated with an organosilane10.1002/sia.1918 ↗
23. Understanding the relationship between silane application conditions, bond durability and locus of failure10.1016/j.ijadhadh.2005.03.009 ↗
24. Direct observation and characterisation of the oxide nanostructured interface resulting from organosilane pre-treamtment of aluminium10.1557/PROC-734-B1.8 ↗
25. The effect of silane incorporation on a metal adhesive interface: A study by electron energy loss spectroscopy10.1016/j.micron.2009.10.001 ↗
26. Structure and properties of organosilane primers for adhesive bonding10.1016/0378-5963(81)90057-X ↗
27. The influence of mechanical and chemical treatments on the envitomental resistance of epoxy adhesive bonds to titanium10.1016/j.ijadhadh.2013.09.012 ↗
28. Influence of adherend surface preparation on bond durability10.1002/(SICI)1096-9918(199912)27:12<1055::AID-SIA675>3.0.CO;2-T ↗
29. Durability of adhesive-bonded joints employinig organosilane coupling agents10.1016/0143-7496(90)90103-5 ↗
30. Treatment of additively manufactured AlSi10Mg surfaces for improved bonding with fiber reinforced composites for sandwich applicationsJ10.1177/10996362211035431 ↗
31. Promotion of resin bonding to dental zirconia ceramic using plasma deposition of tetramethylsilane and benzene10.1111/eos.12316 ↗
32. Effect of silane treatment on adhesion of adhesive-bonded carbon fiber reinforced nylon 6 composite10.1016/j.ijadhadh.2019.03.008 ↗
33. Precipitates and second-phase particles in DC04 steel plate produced by reversible cold rolling
34. Microstructure, mechanical properties and geometry of a model batch of semi-spherical steel liners intended for use in the extractive industry10.32730/imz.2657-747.21.3.2 ↗