journal article·2026-03-01Open access

Regulation of microstructural evolution and tribological performance of extruded magnesium matrix composites reinforced with nano-WS 2

Zhijian He, Nengru Tao

Materials Science-Poland· Volume 44· Issue 1

Abstract

Abstract Extruded magnesium matrix composites reinforced with nano-sized tungsten disulfide were fabricated via powder metallurgy followed by hot extrusion, and their microstructural evolution, mechanical response, and tribological behavior were systematically investigated. Compared with monolithic magnesium, the incorporation of 0.5–2.0 wt% nano-reinforcement markedly altered dynamic recrystallization behavior during extrusion, resulting in pronounced grain refinement and texture modification. Electron backscatter diffraction analysis revealed that the average grain size decreased from approximately 8.5 µm in pure magnesium to about 3.2 µm at 2.0 wt% addition, accompanied by a reduction in basal texture intensity from 12.5 to 7.8 m.r.d. These microstructural changes translated into substantial strengthening, with Vickers hardness increasing from 58 to 92 HV0.1, yield strength from 135 MPa to 220 MPa, and ultimate tensile strength from 210 to 315 MPa, while maintaining elongation above 10%. Tribological tests under dry sliding against GCr15 steel demonstrated a pronounced reduction in friction and wear. The steady-state coefficient of friction decreased from ∼0.45 for unreinforced magnesium to ∼0.18 at 20 N for the composite containing 2.0 wt% reinforcement, and the corresponding wear rate was reduced by nearly one order of magnitude, from ∼1.8 × 10⁻ 4 to ∼1.5 × 10⁻ 5 mm 3 Nm. Surface and debris analyses confirmed the formation of a continuous lubricious tribolayer that mitigated severe adhesive and abrasive wear. The results collectively demonstrate a clear composition–structure–property relationship, highlighting the effectiveness of nanoscale layered reinforcements combined with extrusion processing for achieving a balanced improvement in strength and wear resistance in lightweight metallic composites.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Aluminum Alloys Composites Properties · Magnesium Alloys: Properties and Applications · Advanced Welding Techniques Analysis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

School of Intelligent Manufacturing, Hunan First Normal University , Changsha , China

School of Mechanical Engineering, Guangxi University , Nanning , China

References (49)

Show source-provided references
1. Singhal, V., Shelly, D., Babbar, A., Lee, S.Y., Park, S.J. Review of wear and mechanical characteristics of Al-Si alloy matrix composites reinforced with natural minerals. Lubricants. 2024;12(10):35010.3390/lubricants12100350 ↗
2. Hu, S., Wang, F., Du, X., Mao, P., Wang, Z., Zhou, L., et al. Microstructure, mechanical properties and wear resistance of As-Cast Mg–3Al-1Ca-0.4 Mn/Tip magnesium matrix composites. Int. J. Metalcast. 2025;19(3):1422–143710.1007/s40962-024-01391-9 ↗
3. Wang, H., Luo, X.C., Zhang, D.T., Qiu, C., Chen, D.L. High-strength extruded magnesium alloys: A critical review. J. Mater. Sci. Technol. 2024;199:27–52. 10.1016/j.jmst.2024.01.08910.1016/j.jmst.2024.01.089 ↗
4. Sagar, P., Handa, A., Kumar, G. Metallurgical, mechanical and tribological behavior of reinforced magnesium-based composite developed via friction stir processing. Proc. Inst. Mech. Eng., Part. E: J. Process. Mech. Eng. 2022;236(4):1440–145110.1177/09544089211063099 ↗
5. Patel, S.K., Singh, S., Shi, L., Liu, L., Zhang, X., Guan, L., et al. Microstructural and biological wear behaviour of hybrid reinforced AZ91D alloy surface composite fabricated by friction stir processing technique. Ceram. Int. 2025; 51: 64337–64354. 10.1016/j.ceramint.2025.11.17110.1016/j.ceramint.2025.11.171 ↗
6. Rajoria, S.R., Kanti, S.P., Soni, H., Sahoo, B.N. Development, characterization, and mechanical properties of innovative in situ high-entropy alloy reinforced magnesium matrix composites via ultrasonic-assisted processing. J. Manuf. Process. 2025;142:368–386. 10.1016/j.jmapro.2025.03.09410.1016/j.jmapro.2025.03.094 ↗
7. Ren, J.Y., Ji, G.C., Guo, H.R., Zhou, Y.M., Tan, X., Zheng, W.F., et al. Nano-enhanced phase reinforced magnesium matrix composites: A review of the matrix, reinforcement, interface design, properties and potential applications. Materials. 2024;17(10):2454. 10.3390/ma1710245410.3390/ma17102454 ↗
8. Sahoo, S., Sahoo, B., Panigrahi, S. Investigation into machining performance of microstructurally engineered in-situ particle reinforced magnesium matrix composite. J. Magnes. Alloy. 2023;11(3):916–93510.1016/j.jma.2022.10.015 ↗
9. Bharathi, P., Sampath Kumar, T. Latest research and developments of ceramic reinforced magnesium matrix composites—A comprehensive review. Proc. Inst. Mech. Eng., Part. E: J. Process. Mech. Eng. 2023;237(3):1014–103510.1177/09544089221126044 ↗
10. Aliasker, K., Gopal, P., Naveen, S., Madhu, S., Yuvaraj, K. Exploring the effects of self-lubricating MoS2 in magnesium metal matrix composite: investigation on wear, corrosion, and mechanical properties. Colloids Surf. A: Physicochem. Eng. Asp. 2023;677:13236210.1016/j.colsurfa.2023.132362 ↗
11. Babu, P., Solomon, D.G. Mechanical and tribological properties of magnesium composites–A review. Mater. Today: Proc. 2023;1:422. 10.1016/j.matpr.2023.07.06510.1016/j.matpr.2023.07.065 ↗
12. Moradpur-Tari, E., Sarraf-Mamoory, R., Yourdkhani, A. Structural, electronic, and electrochemical studies of WS2 phases using density functional theory and machine learning. Phys. B: Condens. Matter. 2023;650:414568. 10.1016/j.physb.2022.41456810.1016/j.physb.2022.414568 ↗
13. Ren, G., Wu, X., Cai, W., Gong, P., Chen, Y., Liu, P., et al. WS2 nanosheet thickness modulation for wear-resistant carbon–graphite composites. Tribol. Int. 2026;214:111359. 10.1016/j.triboint.2025.11135910.1016/j.triboint.2025.111359 ↗
14. Zhang, H., Wang, W., Zhang, S., Zhang, Y., Zhou, J., Wang, Z., et al. A novel method based on deep reinforcement learning for machining process route planning. Robot. Comput.-Integr. Manuf. 2024;86:102688. 10.1016/j.rcim.2023.10268810.1016/j.rcim.2023.102688 ↗
15. Dey, A., Pandey, K.M. Wear behaviour of Mg alloys and their composites–a review. Int. J. Mater. Res. 2018;109(11):1050–1070
16. Patel, S.K., Shi, L., Kumar, A., Wu, C., Mironov, S., Zhou, M., et al. A critical review on development of magnesium-based bio-implants surface composite through friction stir processing route. Crit. Rev. Solid. State Mater. Sci. 2025;7:1–8610.1080/10408436.2025.2560335 ↗
17. Li, Q., Zhang, X., Wang, L., Qiao, J. The effect of extrusion and heat treatment on the microstructure and tensile properties of 2024 aluminum alloy. Materials. 2022;15(21):7566. 10.3390/ma1521756610.3390/ma15217566 ↗
18. Zhou, H., Ruan, A., Zhang, H., Wang, B., Sun, J., Qin, S., et al. Hot deformation behavior and dynamic recrystallization mechanism of Cr-Co-Ni particle-reinforced AZ31 magnesium matrix composite. J. Alloy. Compd. 2025;1022:17992310.1016/j.jallcom.2025.179923 ↗
19. Yuan, L., Zheng, B., Kunstmann, J., Brumme, T., Kuc, A.B., Ma, C., et al. Twist-angle-dependent interlayer exciton diffusion in WS2–WSe2 heterobilayers. Nat. Mater. 2020;19(6):617–623. 10.1038/s41563-020-0670-310.1038/s41563-020-0670-3 ↗
20. Zhong, Y., Yue, S., Liang, J., Yuan, L., Xia, Y., Tian, Y., et al. Twist angle-dependent exciton mobility in WS2 bilayers. Nano Lett. 2025;25(13):5274–5282. 10.1021/acs.nanolett.5c0002710.1021/acs.nanolett.5c00027 ↗
21. Somveer, Ahlawat, D.S., Singh, D., Gangwar, J. Enhanced structural, morphological and optical properties of WS2 nanorods synthesized via hydrothermal methodology. Mater. Sci. Eng.: B. 2025;313:117935. 10.1016/j.mseb.2024.11793510.1016/j.mseb.2024.117935 ↗
22. Almotairy, S.M., Alharthi, N.H., Alharbi, H.F., Abdo, H.S. Superior mechanical performance of inductively sintered Al/SiC nanocomposites processed by novel milling route. Sci. Rep. 2020;10(1):10368. 10.1038/s41598-020-67198-w10.1038/s41598-020-67198-w ↗
23. Desai, K.R., Alone, S.T., Wadgane, S.R., Shirsath, S.E., Batoo, K.M., Imran, A., et al. X-ray diffraction based Williamson–Hall analysis and rietveld refinement for strain mechanism in Mg–Mn co-substituted CdFe2O4 nanoparticles. Phys. B: Condens. Matter. 2021;614:413054. 10.1016/j.physb.2021.41305410.1016/j.physb.2021.413054 ↗
24. Ye, J., Chen, X., Luo, H., Zhao, J., Li, J., Tan, J., et al. Microstructure, mechanical properties and wear resistance of Ti particles reinforced AZ31 magnesium matrix composites. J. Magnes. Alloy. 2022;10(8):2266–227910.1016/j.jma.2022.06.012 ↗
25. Liu, A., Wang, R., Zhang, X., Feng, J., Li, W., Yu, S., et al. On the friction and wear behaviors of a magnesium matrix composite containing 20 vol% Mg2Sn reinforcement. Tribol. Trans. 2025;13:1–1310.1080/10402004.2025.2505765 ↗
26. Singhal, V., Shelly, D., Saxena, A., Gupta, R., Verma, V.K., Jain, A. Study of the influence of nanoparticle reinforcement on the mechanical and tribological performance of aluminum matrix composites—a review. Lubricants. 2025;13(2):9310.3390/lubricants13020093 ↗
27. Khodabakhshi, F., Simchi, A., Kokabi, A. Surface modifications of an aluminum-magnesium alloy through reactive stir friction processing with titanium oxide nanoparticles for enhanced sliding wear resistance. Surf. Coat. Technol. 2017;309:114–12310.1016/j.surfcoat.2016.11.060 ↗
28. Xue, C., Gao, B., Han, T., Che, C., Chu, Z., Tuo, L. Dislocation evolution mechanism of plastic deformation process of AZ31 magnesium alloy with different grain size. Comput. Mater. Sci. 2024;231:112606. 10.1016/j.commatsci.2023.11260610.1016/j.commatsci.2023.112606 ↗
29. Rahman, M.A., Yomogida, Y., Ahad, A., Ueji, K., Nagano, M., Ihara, A., et al. Synthesis and optical properties of WS2 nanotubes with relatively small diameters. Sci. Rep. 2023;13(1):16959. 10.1038/s41598-023-44072-z10.1038/s41598-023-44072-z ↗
30. Vedabouriswaran, G., Aravindan, S. Wear characteristics of friction stir processed magnesium RZ5 composites. J. Tribol. 2019;141(4):04160110.1115/1.4042039 ↗
31. Banerjee, S., Sahoo, P., Davim, J.P. Tribological characterisation of magnesium matrix nanocomposites: A review. Adv. Mech. Eng. 2021;13(4):1687814021100902510.1177/16878140211009025 ↗
32. Aydın, F. Tribological aspects of magnesium matrix composites: A review of recent experimental studies. Tribol.-Mater., Surf. Interfaces. 2023;17(4):363–39610.1080/17515831.2023.2246809 ↗
33. Li, C., Sang, D., Ge, S., Zou, L., Wang, Q. Recent excellent optoelectronic applications based on two-dimensional WS2 nanomaterials: A review. Molecules. 2024;29(14):3341. 10.3390/molecules2914334110.3390/molecules29143341 ↗
34. Wang, C.-r., Deng, K.-k. Microstructure, and mechanical and wear properties of Grp/AZ91 magnesium matrix composites. Materials. 2019;12(7):119010.3390/ma12071190 ↗
35. Xia, Y., Zhang, X., Zhao, D., Rong, X., He, C., Zhao, N. Breaking the strength-ductility trade-off for metal matrix composites: A review of the role of nanoscale reinforcement dimension on the deformation and strengthening mechanisms. Rev. Mater. Res. 2025;1(1):100019. 10.1016/j.revmat.2025.10001910.1016/j.revmat.2025.100019 ↗
36. Tang, Y., Wang, H., Ouyang, X., Wang, C., Huang, Q., Zhao, Q., et al. Overcoming strength-ductility tradeoff with high pressure thermal treatment. Nat. Commun. 2024;15(1):3932. 10.1038/s41467-024-48435-610.1038/s41467-024-48435-6 ↗
37. Žemlička, R., Souček, P., Vogl, P., Jílek, M., Buršíková, V., Vašina, P., et al. On the significance of running-in of hard nc-TiC/a-C:H coating for short-term repeating machining. Surf. Coat. Technol. 2017;315:17–23. 10.1016/j.surfcoat.2017.02.02010.1016/j.surfcoat.2017.02.020 ↗
38. Gazzato, L., Missale, E., Asnicar, D., Sedona, F., Speranza, G., Del Giudice, A., et al. Structural insights into the mechanical behavior of large-area 2D covalent organic framework nanofilms. ACS Appl. Mater. Interfaces. 2025;17(17):25819–25827. 10.1021/acsami.5c0351210.1021/acsami.5c03512 ↗
39. Rodríguez Ripoll, M., Tomala, A.M., Pirker, L., Remškar, M. In-situ formation of MoS2 and WS2 tribofilms by the synergy between transition metal oxide nanoparticles and sulphur-containing oil additives. Tribol. Lett. 2020;68(1):41. 10.1007/s11249-020-1286-010.1007/s11249-020-1286-0 ↗
40. Guo, L., Yin, Y., Gao, L., Lin, H., Liu, Y., Le, K., et al. Tribofilm formation by Fe3O4 nanoparticles as lubricant additives: Microscopic insights into growth conditions and mechanisms. Tribol. Lett. 2025;73(2):50. 10.1007/s11249-025-01988-z10.1007/s11249-025-01988-z ↗
41. Liu, Y., Liu, C.H., Debnath, T., Wang, Y., Pohl, D., Besteiro, L.V., et al. Silver nanoparticle enhanced metal-organic matrix with interface-engineering for efficient photocatalytic hydrogen evolution. Nat. Commun. 2023;14(1):541. 10.1038/s41467-023-35981-810.1038/s41467-023-35981-8 ↗
42. Nam, J.M., Owen, J.S., Talapin, D.V. The ligand–surface interface and its influence on nanoparticle properties. Acc. Chem. Res. 2023;56(17):2265–2266. 10.1021/acs.accounts.3c0041610.1021/acs.accounts.3c00416 ↗
43. Matsuda, T., Hayashi, K., Iwamoto, C., Nozawa, T., Ohata, M., Hirose, A. Crack initiation and propagation behavior of dissimilar interface with intermetallic compound layer in Al/steel joint using coupled multiscale mechanical testing. Mater. Des. 2023;235:112420. 10.1016/j.matdes.2023.11242010.1016/j.matdes.2023.112420 ↗
44. Li, B., Chen, H., Li, G., Wei, G., Xie, W. Strengthening and toughening mechanisms of CNTs/Mg–Al composites prepared via powder metallurgy combined with hot extrusion. Vacuum. 2023;214:112210. 10.1016/j.vacuum.2023.11221010.1016/j.vacuum.2023.112210 ↗
45. Zhang, Y., Nizolek, T.J., Capolungo, L., Li, N., Carpenter, J.S., McCabe, R.J. Strong interfaces: the key to high strength in nano metallic laminates. Acta Mater. 2024;280:120298. 10.1016/j.actamat.2024.12029810.1016/j.actamat.2024.120298 ↗
46. Wang, G., Zhang, Y., Liu, J., Chen, W., Wang, K., Cui, B., et al. Dispersion hardening using amorphous nanoparticles deployed via additive manufacturing. Nat. Commun. 2025;16(1):3589. 10.1038/s41467-025-58893-110.1038/s41467-025-58893-1 ↗
47. Zhu, J., Qi, J., Guan, D., Ma, L., Dwyer-Joyce, R. Tribological behaviour of self-lubricating Mg matrix composites reinforced with silicon carbide and tungsten disulfide. Tribol. Int. 2020;146:106253. 10.1016/j.triboint.2020.10625310.1016/j.triboint.2020.106253 ↗
48. Subramani, M., Huang, S.J., Borodianskiy, K. Effect of WS2 nanotubes on the mechanical and wear behaviors of AZ31 stir casted magnesium metal matrix composites. J. Compos. Sci. 2022;6(7):182. 10.3390/jcs607018210.3390/jcs6070182 ↗
49. Narayanasamy, P., Selvakumar, N. Tensile, compressive and wear behaviour of self-lubricating sintered magnesium based composites. Trans. Nonferrous Met. Soc. China. 2017;27(2):312–323. 10.1016/S1003-6326(17)60036-010.1016/S1003-6326(17)60036-0 ↗