journal article·2025Open access

Optimizing alumina reinforcement in kevlar-epoxy composites: a study on mechanical and tribological enhancements

Vasanthkumar Periyathambi, S. Rajamanickam, Mohan Govindasamy, Manikandan Ezhumalai, Deekshant Varshney, Subhav Singh, Ratchagaraja Dhairiyasamy, Bahaa Saleh, Ahmed Hassan

Abstract

Abstract Kevlar-reinforced epoxy composites are widely employed in high-performance applications due to their excellent strength-to-weight ratio and impact resistance. However, limitations in wear resistance hinder their use under abrasive conditions. To address this, Alumina (Al2O3) was incorporated as particulate filler at 2%, 4%, and 6% by weight. Composite laminates were fabricated using hand layup followed by compression molding, with a constant Kevlar fiber content of 30 wt%. Mechanical testing was conducted as per ASTM D3039 (tensile), ASTM D790 (flexural), and ASTM D785 (hardness) standards, while wear behavior was evaluated under dry sliding conditions using ASTM G99 with a pin-on-disc setup at 10 N load, 1.5 m/s sliding velocity, and 500 m sliding distance. The addition of 4% alumina yielded optimal performance, resulting in a 28% increase in tensile strength (from 98 MPa to 126 MPa), a 21.6% increase in flexural strength (from 152 MPa to 185 MPa), and a 12.2% increase in hardness (from 82 HRB to 92 HRB) compared to the control. The wear rate was reduced from 3.12 × 10−4 mm3/N·m in the control to 1.89 × 10−4 mm3/N·m at 4% alumina, representing a 39.4% improvement. The coefficient of friction also decreased from 0.52 (control) to 0.46 at 4% alumina.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Tribology and Wear Analysis · Natural Fiber Reinforced Composites · Mechanical Behavior of Composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

SRM Institute of Science and Technology, India

Vel Tech High Tech Dr. Rangarajan Dr. Sakunthala Engineering College, India

University College of Engineering Villupuram, India

Chitkara University, India; Uttaranchal University, India

Chitkara University, India; Lovely Professional University, India

Saveetha School of Engineering, India

Taif University, Saudi Arabia

Jazan University, Saudi Arabia

Funding

Taif University

References (71)

Show source-provided references
1. “Investigation on the morphology, thermal properties, and in vitro cytotoxicity of the fish scale particulates filled high-density polyethylene composite”10.1177/0967391119872877 ↗
2. “Tribological characterization of epoxy hybrid composites reinforced with Al2O3 nanofiller”10.1155/2023/8196933 ↗
3. “Characterization and in vitro cytotoxicity evaluation of fish scale and seashell derived nano-hydroxyapatite high-density polyethylene composite”10.1177/0967391120981551 ↗
4. “Enhancing flexural capacity and crack resistance of two-span continuous beams with engineered cementitious composite (ECC) under static loading conditions”10.1590/1517-7076-rmat-2024-0671 ↗
5. “Machining performance of silicon carbide ceramic in end electric discharge milling”10.1016/j.ijrmhm.2010.09.001 ↗
6. “Innovative utilization of prosopis juliflora bark nanoparticles in hybrid composites for high-performance automotive applications”10.1590/1517-7076-rmat-2024-0875 ↗
7. “Characterization of Syzygium cumini particulates filled E-glass fiber-reinforced epoxy composites”10.1002/pc.26298 ↗
8. “Development and characterization of Hevea brasiliensis particulates filled polyethylene composites”10.1002/pc.26519 ↗
9. “Optimization of tribological parameters of hybrid polymer composites reinforced with kenaf fibers and recycled spent abrasive particles”10.1590/1517-7076-rmat-2024-0941 ↗
10. “Investigation of product quality monitoring in the compression molding process of carbon fibre reinforced composite laminates”
11. “Mechanical properties of natural fiber reinforced natural and ceramic fillers for various engineering applications”10.1007/s10751-024-02109-3 ↗
12. “Enhancing mechanical and tribological performance of hybrid composites: An experimental study utilizing response surface methodology and firefly algorithm”10.1002/pc.28880 ↗
13. “Parametric appraisal and wear prediction of red brick dust filled epoxy composites using finite element method”10.1002/mawe.202400161 ↗
14. “Sliding wear behaviour of micro-sized Kota stone dust reinforced epoxy composites using Taguchi method and Grey Wolf optimisation algorithm”10.1177/09544062231219578 ↗
15. “Mechanical (static and dynamic) characterization and thermal stability of hybrid green composites for engineering applications”10.1016/j.jmrt.2024.05.132 ↗
16. “Wear and frictional performance of epoxy composites reinforced with natural waste fibers and fillers for engineering applications”10.1007/s12221-024-00519-2 ↗
17. “Investigation on the fracture and creep behavior of the synthetic and Natural fiber laminate polymer composite”10.1590/1517-7076-rmat-2024-0608 ↗
18. “Enhancing mechanical properties of basalt fibre composites with clamshell waste from sea bed”10.5276/jswtm/iswmaw/503/2024.532 ↗
19. “Influence of Prosopis juliflora bark powder/fillers on the mechanical, thermal and damping properties of jute fabric hybrid composites”10.1016/j.jmrt.2024.10.066 ↗
20. “A novel study on the stacking sequence and mechanical properties of Jute-Kevlar-Epoxy composites”10.1007/s10751-024-01946-6 ↗
21. “Investigation on morphological and tensile properties of chemically treated Borassus Flabellifer Lontar fruit fibers”10.1590/1517-7076-rmat-2024-0166 ↗
22. “Optimizing high strength concrete: a comprehensive study on the synergistic effects of natural fibres and silica fume on workability, mechanical and flexural behavior”10.1590/1517-7076-rmat-2024-0525 ↗
23. “Flexural performance of reinforced concrete beam with layer of hybrid strain-hardening cementitious composites”10.1590/1517-7076-rmat-2024-0697 ↗
24. “Bio-inspired attachment mechanism of dynastes hercules: vertical climbing for on-orbit assembly legged robots”10.1007/s42235-023-00423-0 ↗
25. “Analysis of compressive strength of nanostructure pyrolytic carbon enhanced nanocomposite mortar and forecasting using machine learning models”10.1590/1517-7076-rmat-2024-0911 ↗
26. “Experimental study of a composite beam externally bonded with a carbon fiber-reinforced plastic plate”10.1016/j.jobe.2023.106522 ↗
27. “Experimental investigation on development and machinability of copper matrix hybrid composite-graphene and SiC/TiC/ZrO2/AlMg reinforcements”10.1590/1517-7076-rmat-2024-0837 ↗
28. “Microdynamic behaviors of Au/Ni-assisted chemical etching in fabricating silicon nanostructures”10.1016/j.apsusc.2025.162915 ↗
29. “Empirical modeling of residual stress profile for multi-axis milling GH4169G”10.1007/s00170-025-15257-9 ↗
30. “Investigation of water-based drilling fluid properties modified by nano ZnO-polyacrylamide composite”10.1590/1517-7076-rmat-2024-0835 ↗
31. “Effect of solution and aging treatment on the microstructure and properties of LAZ931 Mg-Li alloy by friction stir processing”10.3390/met15030314 ↗
32. “Nano iron particles influence on mechanical properties and morphological analysis of polymer composites”10.1590/1517-7076-rmat-2024-0698 ↗
33. “Study on the damage mechanism of high-speed turnout switch rails on large ramps”10.1007/s11771-025-5858-x ↗
34. “Phenolic-based porous composite with embedded short carbon fiber/hollow spheres for mechanical properties and thermostability”10.1016/j.coco.2025.102305 ↗
35. “Prediction model for surface shape of YAG wafers in wafer rotational grinding”10.1016/j.ijmecsci.2025.109982 ↗
36. “Pioneering the next frontier in construction with high-strength concrete infused by nano materials”10.1590/1517-7076-rmat-2024-0730 ↗
37. “Robust macroscale superlubricity in humid air via designing amorphous DLC/crystalline TMDs friction pair”10.1002/adfm.202316036 ↗
38. “Dynamic interfacial electrostatic energy harvesting via a single wire”10.1126/sciadv.ado5362 ↗
39. “Prediction of particle-reinforced composite material properties based on an improved Halpin-Tsai model”10.1063/5.0206774 ↗
40. “Microstructure and mechanical properties of WC-12Co cemented carbide fabricated by laser powder bed fusion on a WC-20Co cemented carbide substrate”10.1016/j.jmrt.2024.05.266 ↗
41. “Investigation of variable-temperature wear characteristics of austenitic stainless steel coatings fabricated via laser energy deposition”10.1016/j.wear.2025.205993 ↗
42. “High deformation/damage localization accuracy of fibrous composites through deep-learning of single channel data from carbon nanotube sensors”10.1016/j.compositesa.2024.108512 ↗
43. “Fabrication, characterization and in vitro assessment of laevistrombus canarium-derived hydroxyapatite particulate-filled polymer composite for implant applications”10.3390/polym14050872 ↗
44. “In-vitro cytotoxicity of zinc oxide, graphene oxide, and calcium carbonate nano particulates reinforced high-density polyethylene composite”10.1016/j.jmrt.2022.03.012 ↗
45. “A highly ductile carbon material made of triangle rings: A study of machine learning”10.1063/5.0189906 ↗
46. “Influence of solid solution treatment on fatigue crack propagation behavior in the thickness direction of 2519A aluminum alloy thick plates”10.1016/j.engfracmech.2024.110069 ↗
47. “Wear Resistance of N-Doped CoCrFeNiMn high entropy alloy coating on the Ti-6Al-4V alloy”10.1007/s11666-024-01864-7 ↗
48. “Development and in-vitro characterization of HAP blended PVA/PEG bio-membrane”10.1016/j.jmrt.2022.04.130 ↗
49. “Dual network co-crosslinked HNBR composites with enhanced tribological properties under water lubrication”
50. “Design, fabrication, and characterization of natural fillers loaded HDPE composites for domestic applications”10.1002/pc.26806 ↗
51. “Development of biocomposites from samanea saman fillers reinforced with PLA”10.1007/s13399-022-03410-3 ↗
52. “Effect of chemical and biological treatments on Agave americana yarn braid reinforced composite structures”10.1016/j.matchemphys.2022.127236 ↗
53. “HDPE/hydroxyapatite/zeolite composite - characterization and in vitro cytotoxicity”10.14314/polimery.2024.9.4 ↗
54. “A mixed visco-hyperelastic hydrodynamic lubrication model for water-lubricated rubber bearings”10.1016/j.ijmecsci.2024.109887 ↗
55. “Novel Polyalthia Longifolia seed fillers loaded and E-glass fiber-reinforced sandwich epoxy composites”10.1177/09544089231158453 ↗
56. “Mechanical and Materialistic Characterization of Poly Lactic Acid/Zeolite/Hydroxyapatite Composites”10.1007/s10904-023-02647-3 ↗
57. “Attempt to identify antimicrobial Tridax procumbens (TP) mechanical properties using experimental work coupled with FEM model for biomedical applications”10.1016/j.jmbbm.2023.106086 ↗
58. “In vitro-in vivo wound healing efficacy of Tridax Procumbens extract loaded Carboxymethylcellulose film”10.1016/j.ijbiomac.2023.126695 ↗
59. “Multifunctional and sustainable hydroxyapatite from natural products for biomedical and industrial applications – A comprehensive review”10.1016/j.scp.2024.101653 ↗
60. “Evaluation of microwave irradiated Polyacrylamide grafted Opuntia leaf mucilage graft copolymer (OPM-g-PAM) as effective controlled release polymer for release of Rosuvastastin as model drug”10.1016/j.ijbiomac.2024.133200 ↗
61. “Experimental evaluation and numerical comparisons of pine tree leaves, graphene oxide loaded, and E-glass fiber reinforced sandwich composites”10.1080/1023666X.2024.2371426 ↗
62. “In-vitro and in-vivo investigation of wound healing efficacy of Syzygium cumini leaf extracts loaded carboxymethylcellulose film”10.1016/j.ijbiomac.2024.133691 ↗
63. “Experimental and numerical analysis of natural fillers loaded and E-glass reinforced epoxy sandwich composites”10.1016/j.jmrt.2024.07.142 ↗
64. “Thermoplastic bio-composites from natural Samanea Saman fillers loaded HDPE: Mechanical, thermal, and structural analysis”10.1016/j.rineng.2024.102841 ↗
65. “Investigation of coconut shell fillers loaded and pine apple fiber reinforced epoxy sandwich composites”10.1007/s10965-024-04205-y ↗
66. “Influence of dielectric and machining parameters on the process performance for electric discharge milling of SiC ceramic”10.1007/s00170-011-3493-1 ↗
67. “Enhancing mechanical performance of TiO2 filler with Kevlar/epoxy-based hybrid composites in a cryogenic environment: a statistical optimization study using RSM and ANN methods”10.3389/fmats.2023.1267514 ↗
68. “Fresh, mechanical and microstructural properties of alkali-activated composites incorporating nanomaterials: a comprehensive review”10.1016/j.jclepro.2022.135390 ↗
69. “Evaluation of mechanical properties and simulation of kevlar epoxy reinforced composite with silicon carbide filler”
70. “Mechanical properties of hybrid composite glass fiber and kevlar fiber reinforcement with nano alumina”10.1063/5.0161472 ↗
71. “The mechanical properties of Kevlar fabric/epoxy composites containing aluminosilicates modified with quaternary ammonium and phosphonium salts”10.3390/ma13173726 ↗