Influence of optimized lubrication-cooling and minimum quantity lubrication on the cutting forces, on the geometric quality of the surfaces and on the micro-structural integrity of hardened steel parts
Source abstract
Abstract
The is paper presents an analysis of the influence of minimum quantity lubrication (MQL), optimized and conventional cooling, using different cutting fluid volumes and flow rates, on the surface quality and integrity of hardened steel workpieces, in cylindrical plunge grinding with superabrasive CBN grinding wheels. The final quality of the workpieces were evaluated based on an assessment of output variables such as the behavior of: tangential cutting force, specific energy, surface roughness, roundness errors, acoustic emission, residual stresses, scanning electron microscopy (SEM) micrographs, and microhardness. The present analysis of the various forms of cutting fluid application identified cooling conditions which favor the minimization of cutting fluid usage, and shorter machining times without impairing the geometrical and dimensional parameters, surface finish and surface integrity of the workpieces. Among the various forms of cutting fluid application, optimized lubrication at higher outlet speeds showed the best performance, confirming the efficiency of the new nozzle concept employed in this study. The optimized and MQL processes were successful in maintaining the hardness and surface integrity of the ground workpieces. The only exception was the use of MQL with a flow rate of 40ml/h, which caused cracking and quenching of the workpiece surface. The lowest surface roughness values obtained with MQL were obtained using higher flow rates of lubricant. The surface roughness values obtained with MQL are high for the grinding process. Low-concentration CBN wheels, which are less expensive and subject to less wear, produce good results when associated with more efficient cutting fluid application techniques.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Advanced machining processes and optimization · Metal Alloys Wear and Properties · Advanced Machining and Optimization Techniques
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
São Paulo State University
References (21)
Show source-provided references
1. MALKIN S. · 1989 · 108 a 171
2. GUO C. · 1999 · 1
3. "Optimizing coolant application systems for high productivity grinding"
4. KOVACEVIC R. · 1995 · 919
5. "Grinding fluid application system design"10.1016/S0007-8506(07)62337-3 ↗
6. Analysis of surface integrity for minimum quantity lubricant: MQL in grinding10.1016/j.ijmachtools.2006.03.015 ↗
7. "Performance of aerodynamic baffles in cylindrical grinding analyzed on the basis of air layer pressure and speed"10.1590/S1678-58782008000100007 ↗
8. "Selection of coolant type and application technique in grinding"
9. "Environmentally-conscious minimum quantity lubrification (MQL) for internal cylindrical grinding"
10. Thermal aspects of grinding with electroplated CBN wheels10.1115/1.1644547 ↗
11. "Effects and mechanisms in minimal quantity lubrication machining of an aluminum alloy"10.1016/j.wear.2005.03.035 ↗
12. "The effects of cutting fluid application methods on the grinding process"10.1016/S0890-6955(99)00060-7 ↗
13. Residual stresses: measurement and causes in machining processes10.1016/S0007-8506(07)60172-3 ↗
14. "Monitoring and optimization of internal grinding process"10.1016/S0007-8506(07)62006-X ↗
15. "Energy Partition for Grinding with Aluminum Oxide and CBN Abrasive Wheels"10.1115/1.2803290 ↗
16. "Optimisation of Fluid Application in Grinding"10.1016/j.cirp.2008.03.090 ↗
17. 2011
18. 2011
19. 2011
20. "An assessment of the applicability of cold air and oil mist in surface grinding"10.1016/S0924-0136(03)00714-3 ↗
21. Concrete International: Experimental simulation of the efficiency of high speed grinding wheel cleaning10.1016/j.ijmachtools.2005.04.016 ↗