Fracture behaviour of poly(ether ether ketone) films with different thicknesses
Source abstract
Abstract
Abstract The effect of orientation on the fracture behavior for poly(ether ether ketone) (PEEK) films with different thicknesses (0.05, 0.10, 0.30 and 0.50 mm) has been studied. The initial objective was to study both the modes I and III (tearing) fracture of the PEEK films. For the mode I fracture testing, the essential work of fracture (EWF) analysis was used to characterize the PEEK films as gross yielding in the outer plastic zones was observed. However, for the tearing (mode III) fracture testing using the trousers tear sample, the outer plastic zone could not be developed, and an elastic fracture analysis was carried out. There are additional complications with the trousers tear testing. When the PEEK films are too thick (0.30 and 0.50 mm), the trousers legs will fracture instead of crack propagation in the ligament. For the thinner films tested in one of the sample orientations, the tearing crack can be initiated but will detour gradually into the direction perpendicular to the ligament. In the mode I EWF measurements, DENT specimens were cut from two directions perpendicular to each other. The thinner PEEK films (i.e., 0.05 and 0.10 mm thick) show higher degree of anisotropy as indicated by the F–δ curves, we and βwp values. For the thicker PEEK films (i.e., 0.30 and 0.50 mm thick), the mode I EWF measurement shows that the degree of anisotropy is very mild. Pole figure measurements also support that the thinner films have higher degree of orientation than the thicker films.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Mechanical Behavior of Composites · Polymer crystallization and properties · Tribology and Wear Analysis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (21)
Show source-provided references
1. Effects of gauge length and strain rate on fracture toughness of polyethylene terephthalate glycol (PETG) film using the essential work of fracture analysis10.1002/pen.11164 ↗
2. Effect of strain rate on the fracture toughness of some ductile polymers using the essential work of fracture (EWF) approach10.1002/pen.11386 ↗
3. Essential work of fracture (EWF) analysis for short glass fiber reinforced and rubber toughened nylon-610.1002/pen.10045 ↗
4. On the impact essential work of fracture of ductile polymers10.1002/pen.10703 ↗
5. The essential work of plane-stress ductile fracture of poly(ether–ether ketone) thermoplastic10.1007/BF00351217 ↗
6. Fracture of poly(ether–ether ketone) films
7. Crystal morphology and phase identifications in poly(aryl ether ketone)s and their copolymers. 1. Polymorphism in PEKK10.1021/ma00086a023 ↗
8. Towards phase transformation toughened semicrystalline10.1007/BF00296016 ↗
9. On the essential and non-essential work of fracture of biaxial-oriented filled PET film10.1016/0032-3861(96)85355-9 ↗
10. Thickness dependence of work of fracture parameters of an amorphous copolyester10.1016/S0032-3861(96)01061-0 ↗
11. Effect of glass fiber and maleated ethylene–propylene rubber content on the impact fracture parameters of nylon 610.1016/S0032-3861(01)00068-4 ↗
12. The work of fracture in semiductile polymers10.1007/BF00376277 ↗
13. The application of the essential work of fracture methodology to the plane strain fracture of ABS 3-point bend specimens10.1016/S0032-3861(02)00849-2 ↗
14. The essential work of fracture for tearing of ductile metals10.1007/BF00032685 ↗
15. On the essential work of ductile fracture in polymers10.1007/BF00019787 ↗
16. Essential work of fracture and J-integral measurements for ductile polymers10.1002/polb.1991.090290702 ↗
17. The essential work of plane stress ductile fracture of linear polyethylenes10.1002/pen.760271106 ↗
18. Plane-stress essential work of ductile fracture for polycarbonate10.1007/BF01105033 ↗
19. On tearing of ductile polymer films using the essential work of fracture (EWF) method10.1016/S1359-6454(03)00335-5 ↗
20. The essential work concept for toughness measurement of ductile polymers10.1002/pen.10626 ↗
21. Fracture toughness and fracture mechanisms of PBT/PC/IM blend, part I: fracture properties10.1007/BF00354261 ↗