journal article·2014-09

Low stress mechanical properties of fabrics woven from bamboo viscose blended yarns

Abhijit Majumdar, Sagar Baburao Pol

Fibers and Polymers· Volume 15· Issue 9
Publisher page

Abstract

This paper presents the low stress mechanical properties of plain fabrics woven from cotton, bamboo viscose and cotton-bamboo viscose blended yarns. Three blends (100 % cotton, 50:50 cotton-bamboo and 100 % bamboo) were used to produce three yarn counts (20, 25 and 30 Ne). Each of these yarns was used to make fabrics with different pick densities (50, 60 and 70 picks per inch). It was found that bending rigidity, bending hysteresis, shear rigidity, shear hysteresis and compressibility is lower for bamboo fabrics as compared to those of 100 % cotton fabrics. On the other hand, extensibility, tensile energy and compressional resilience are higher for 100 % bamboo fabrics than 100 % cotton fabrics. Higher pick density increases linearity of load-elongation curve, bending rigidity, shear rigidity and compressional resilience. Shear and bending rigidities show very good correlation with the respective hysteresis values.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Textile materials and evaluations · Natural Fiber Reinforced Composites · Color perception and design

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (18)

Show source-provided references
1. A. Majumdar, S. Mukhopadhyay, R. Yadav, and A. K. Mondal, Ind. J. Fibre Text. Res., 36, 18 (2011).
2. N. Erdumlu and B. Ozipek, Fibers Text. East. Eur., 16, 43 (2008).
3. S. S. Mahish, A. K. Patra, and R. Thakur, Ind. J. Fibre Text. Res., 37, 231 (2012).
4. P. Hatua, A. Majumdar, and A. Das, Photodermatology, Photoimmunology and Photomedicine, 29, 182 (2013).10.1111/phpp.12045 ↗
5. I. R. Hardin, S. S. Wilson, R. Dhandapani, and V. Dhende, AATCC Rev., 9, 33 (2009).
6. A. Majumdar, S. Mukhopadhyay, and R. Yadav, Int. J. Therm. Sci., 49, 2042 (2010).10.1016/j.ijthermalsci.2010.05.017 ↗
7. C. Prakash, G. Ramakrishnan, and C. V. Koushik, J. Therm Anal. Calorim, 110, 1173 (2012).10.1007/s10973-011-2066-8 ↗
8. S. Kawabata, “Measurement of Mechanical Properties of Fabric”, The Standardization and Analysis of Hand Evaluation, 2nd ed., Japan, 1980.
9. T. K. Ghosh, S. K. Batra, and S. P. Hersh, J. Text. Inst., 81, 255 (1990).10.1080/00405009008658709 ↗
10. T. K. Ghosh, S. K. Batra, and S. P. Hersh, J. Text. Inst., 81, 272 (1990).10.1080/00405009008658710 ↗
11. M. Matsuraida, K. Nakano, Y. Yamazaki, Y. Hayashi, and O. Hayashi, J. Text. Inst., 100, 265 (2009).10.1080/00405000701757727 ↗
12. W. M. Lo and J. L. Hu, Text. Res. J., 72, 383 (2002).10.1177/004051750207200502 ↗
13. B. K. Behera, AUTEX Res. J., 7, 33 (2007).10.1515/aut-2007-070104 ↗
14. R. K. Nayak, S. K. Punj, K. N. Chatterjee, and B. K. Behera, Ind. J. Fibre Text. Res., 34, 122 (2009).
15. R. H. Yang, C. W. Kan, W. Y. Wong, and M. C. Law, Fiber. Polym., 14, 669 (2013).10.1007/s12221-013-0669-3 ↗
16. C. W. Kan, C. W. M. Yuen, Y. L. Lam, and C. K. Chan, Fiber. Polym., 10, 325 (2009).10.1007/s12221-009-0325-0 ↗
17. R. Mishra, B. K. Behera, and B. P. Pal, J. Text. Inst., 103, 320 (2012).
18. M. Matsudaira and H. Qin, J. Text. Inst., 86, 476 (1995).10.1080/00405009508658774 ↗