journal article·2022-03

Spray parameters optimization, microstructure and corrosion behavior of high-velocity oxygen-fuel sprayed non-equiatomic CuAlNiTiSi medium-entropy alloy coatings

Jie Cheng, Yuping Wu, Sheng Hong, Jiangbo Cheng, Lei Qiao, Yujun Wang, Shuaishuai Zhu

Intermetallics· Volume 142
Publisher page

Abstract

In this study, a novel Cu 55Al 20Ni 12Ti 8Si 5 (at.%) medium-entropy alloy (MEA) was designed, and the Cu-based MEA coating was deposited on the AISI 1020 steel substrate via high-velocity oxygen-fuel (HVOF) spraying process. With the porosity of the coatings as objective, Taguchi method was employed to optimize the three influential HVOF spray parameters. Phase composition, microstructure, microhardness of the optimized coating was characterized by means of XRD, SEM/EDS and STEM techniques, Vickers microhardness tester, respectively. The corrosion behavior of the coatings, as-cast Ni-Al bronze and AISI 1020 steel was investigated in 3.5 wt% NaCl solution by using electrochemical test methods. The XPS was adopted to characterize the composition of corrosion products, and the corrosion mechanism was further discussed. The results illustrated that oxygen flow had a dramatic impact on the porosity of the coatings, and the optimized coating can be prepared under oxygen flow of 802.3 L/min, kerosene flow of 0.38 L/min and spray distance of 320 mm. Detailed characterization indicated that the optimized coating was comprised of mainly Cu-rich BCC phase and a few granular NiTi-rich B2-ordered phase with a porosity of 0.42% ± 0.06% and a microhardness of 470 ± 31 HV 0.2 . The electrochemical test results revealed that the optimized coating exhibited superior corrosion resistance relative to that of all orthogonal coatings, as-cast Ni-Al bronze and AISI 1020 steel on account of its low porosity and primarily single-phase microstructure. Additionally, the long-term corrosion behavior of the optimized coating was controlled by electrochemical reaction that promoting the formation of protective film on the coating surface, which can efficiently improve the corrosion resistance of the coating.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: High Entropy Alloys Studies · High-Temperature Coating Behaviors · Advanced materials and composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (56)

Show source-provided references
1. The effect of phase fraction, size and shape on the dezincification of duplex brasses10.1016/j.corsci.2021.109366 ↗
2. A novel electrodeposited Cu-Zn-Bi film with increased corrosion resistance in a 0.05 M K2SO4 solution10.1016/j.apsusc.2011.08.122 ↗
3. Microstructure design to improve the corrosion and cavitation corrosion resistance of a nickel-aluminum bronze10.1016/j.corsci.2018.04.043 ↗
4. Effect of heat treatment on microstructure evolution and erosion-corrosion behavior of a nickel-aluminum bronze alloy in chloride solution10.1016/j.corsci.2015.05.037 ↗
5. Cavitation erosion behavior of friction stir processed nickel aluminum bronze10.1016/j.jallcom.2019.04.302 ↗
6. Synergistic effect between cavitation erosion and corrosion for various copper alloys in sulphide-containing 3.5% NaCl solutions10.1016/j.wear.2020.203258 ↗
7. Effect of laser surface melting on the corrosion and cavitation erosion behaviors of a manganese-nickel-aluminium bronze10.1016/j.msea.2004.01.016 ↗
8. A hexagonal close-packed high-entropy alloy: the effect of entropy10.1016/j.matdes.2016.01.149 ↗
9. Understanding phase stability of Al-Co-Cr-Fe-Ni high entropy alloys10.1016/j.matdes.2016.07.073 ↗
10. A critical review of high entropy alloys and related concepts10.1016/j.actamat.2016.08.081 ↗
11. Alloy design strategies and future trends in high-entropy alloys10.1007/s11837-013-0761-6 ↗
12. Novel microstructure and properties of multicomponent CoCrCuFeNiTix alloys10.1016/j.intermet.2006.08.005 ↗
13. Effect of Cu addition on the microstructure and mechanical properties of AlCoCrFeNiTi0.5 solid-solution alloy10.1016/j.jallcom.2007.11.110 ↗
14. Prediction of high-entropy stabilized solid-solution in multi-component alloys10.1016/j.matchemphys.2011.11.021 ↗
15. Gao · 2016
16. A nanocrystalline AlCoCuNi medium-entropy alloy with high thermal stability via entropy and boundary engineering10.1016/j.msea.2020.138925 ↗
17. Alloy design and fabrication of ingots in Cu-Zn-Mn-Ni-Sn high-entropy and Cu-Zn-Mn-Ni medium-entropy brasses10.1016/j.matdes.2019.107900 ↗
18. Effect of μ-precipitates on the microstructure and mechanical properties of non-equiatomic CoCrFeNiMo medium-entropy alloys10.1016/j.jallcom.2018.12.040 ↗
19. Manufacturing of FeCoCrNiCux medium-entropy alloy coating using laser cladding technology10.1016/j.matdes.2017.07.045 ↗
20. Aspects of microstructure on the synergy and overall material loss of thermal spray coatings in erosion-corrosion environments10.1016/j.wear.2007.01.071 ↗
21. Cavitation erosion characteristics at various flow velocities in NaCl medium of carbide-based cermet coatings prepared by HVOF spraying10.1016/j.ceramint.2020.09.022 ↗
22. Solid particle erosion-corrosion behaviour of a novel HVOF nickel aluminium bronze coating for marine applications-correlation between mass loss and electrochemical measurements10.1016/j.wear.2004.02.019 ↗
23. Microstructure and cavitation erosion behavior of HVOF sprayed ceramic-metal composite coatings for application in hydro-turbines10.1016/j.renene.2020.08.099 ↗
24. Effect of spray parameters on the corrosion behavior of HVOF sprayed WC-Co-Cr coatings10.1007/s11665-014-0865-3 ↗
25. High-velocity oxygen-fuel spray parameter optimization of nanostructured WC-10Co-4Cr coatings and sliding wear behavior of the optimized coating10.1016/j.matdes.2013.10.002 ↗
26. Effect of oxygen/fuel ratio on the microstructure and properties of HVOF-sprayed Al59Cu25.5Fe12.5B3 quasicrystalline coatings10.1016/j.surfcoat.2018.08.081 ↗
27. Relationships between spray parameters, microstructures and ultrasonic cavitation erosion behavior of HVOF sprayed Fe-based amorphous/nanocrystalline coatings10.1016/j.ultsonch.2017.04.011 ↗
28. The influence of HVOF spraying parameters on the microstructure, residual stress and cavitation resistance of FeMnCrSi coatings10.1016/j.surfcoat.2017.07.073 ↗
29. Design of non-equiatomic medium-entropy alloys10.1038/s41598-018-19449-0 ↗
30. Classification of bulk metallic glasses by atomic size difference, heat of mixing and period of constituent elements and its application to characterization of the main alloying element10.2320/matertrans.46.2817 ↗
31. Effects of deformability of HVOF sprayed copper particles on the density of resultant coatings10.1016/j.surfcoat.2005.02.180 ↗
32. Design optimization of cutting parameters for turning operations based on the Taguchi method10.1016/S0924-0136(98)00079-X ↗
33. Application of Taguchi method in the optimization of cutting parameters for surface roughness in turning10.1016/j.matdes.2006.01.008 ↗
34. Application of Taguchi method to selection of optimal lubrication and cutting conditions in face milling of AlMg310.1016/j.jclepro.2010.12.007 ↗
35. The effects of microstructural features on the performance gap in corrosion resistance between bulk and HVOF sprayed Inconel 62510.1016/j.surfcoat.2009.12.028 ↗
36. Effect of oxygen/fuel ratio on the in-flight particle parameters and properties of HVOF WC-CoCr coatings10.1016/j.surfcoat.2011.03.129 ↗
37. Fabrication and characterization of thermal-sprayed Fe-based amorphous/nanocrystalline composite coatings: an overview10.1007/s11666-014-0096-z ↗
38. Experimental optimization of dry sliding wear behavior of in situ AlB2/Al composite based on Taguchi's method10.1016/j.matdes.2012.05.048 ↗
39. Phase evolution, microstructure, and mechanical behaviors of the CrFeNiAlxTiy medium-entropy alloys10.1016/j.msea.2019.138566 ↗
40. Influence of synthesis method on microstructure and mechanical behavior of Co-free AlCrFeNi medium-entropy alloy10.1016/j.intermet.2019.02.006 ↗
41. Review: experimental enthalpies of formation of compounds in Al-Ni-X systems10.1007/s10853-006-6479-x ↗
42. Improvement of surface resistance to cavitation corrosion of nickel aluminum bronze by electropulsing-assisted ultrasonic surface rolling process10.1016/j.surfcoat.2019.03.045 ↗
43. Structure and corrosion resistance properties of Ni-Fe-B-Si-Nb amorphous composite coatings fabricated by laser processing10.1016/j.jallcom.2013.06.111 ↗
44. On the bio-corrosion and biocompatibility of TiTaNb medium entropy alloy films10.1016/j.apsusc.2020.145307 ↗
45. A review of impedance plot methods used for corrosion performance analysis of painted metals10.1016/0010-938X(86)90033-8 ↗
46. Comparison of corrosion and cavitation erosion behaviors between the as-cast and friction-stir-processed nickel aluminum bronze10.5006/0984 ↗
47. Enhanced corrosion resistance of a Cu-10Ni alloy in a 3.5 wt.% NaCl solution by means of ultrasonic surface rolling treatment10.1016/j.surfcoat.2019.02.039 ↗
48. Moulder · 1995
49. Effect of thermo-mechanical treatments on corrosion behavior of Cu-15Ni-8Sn alloy in 3.5 wt.% NaCl solution10.1016/j.matchemphys.2017.06.041 ↗
50. Microstructure evolution and corrosion resistance of Ni-Cu-P amorphous coating during crystallization process10.1016/j.apsusc.2019.04.142 ↗
51. Preparation of novel Cu/TiO2 mischcrystal composites and antibacterial activities for Escherichia coli under visible light10.1016/j.ceramint.2017.04.137 ↗
52. Microstructure, phase and tribocorrosion behavior of 60NiTi alloy10.1016/j.apsusc.2019.143838 ↗
53. Orientation dependence of the electrochemical corrosion properties of electrodeposited Cu foils10.1016/j.corsci.2013.04.046 ↗
54. Effect of nitrogen on corrosion behaviour of a novel high nitrogen medium-entropy alloy CrCoNiN manufactured by pressurized metallurgy10.1016/j.jmst.2018.03.021 ↗
55. Study of the corrosion products formed on a multiphase CuAlBe alloy in a sodium chloride solution by micro-Raman and in situ AFM measurements10.1016/j.apsusc.2011.04.018 ↗
56. Correlation of aging precipitates with the corrosion behaviour of Cu-4 wt.% Ti alloys in 3.5 wt.% NaCl solution10.1016/j.corsci.2016.05.029 ↗