journal article·2023-01

Thermo-mechanical coupled flow behavior evolution of Zr-based bulk metallic glass

Yang Deng, Chengyong Wang, Feng Ding, Tao Zhang, Weikai Wu

Intermetallics· Volume 152
Publisher page

Abstract

Machining is an essential process for manufacturing high-precision bulk metallic glass (BMG) components, but the flow behavior of thermodynamically metastable BMGs during machining with high temperature and high strain rate conditions is still unclear. In this study, the flow behavior of Zr-based BMG is investigated in an orthogonal cutting operation. The results show that the increase of the temperature at the initial stage of cutting enables the amorphous chips gradually change from a laminated structure to a viscous flow state, and attach to the cutting edge of the tool. The chip in the stable sticking area of the tool-chip interface is a composite material rich in various crystalline phases and quasi-crystals with obvious phase separation, while the chips far away from the interface still maintain the amorphous state with uniform composition. After the formation of stable adhesion, the cutting force and cutting temperature are relatively stable, and the viscous-fluid chips act as a protective layer for the tool, avoiding severe tool wear.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Metallic Glasses and Amorphous Alloys

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (31)

Show source-provided references
1. High temperature deformation behavior of the Zr41.2Ti13.8Cu12.5Ni10Be22.5 bulk metallic glass10.1016/S0022-3093(02)01998-1 ↗
2. Deformation behavior of the Zr41.2Ti13.8Cu12.5Ni10Be22.5 bulk metallic glass over a wide range of strain-rates and temperatures10.1016/S1359-6454(03)00164-2 ↗
3. Chip formation, cutting forces, and tool wear in turning of Zr-based bulk metallic glass10.1016/j.ijmachtools.2004.02.002 ↗
4. Oxidation and crystallization of Zr-based bulk metallic glass due to machining10.1016/j.intermet.2003.09.017 ↗
5. Machining of a Zr-Ti-Al-Cu-Ni metallic glass10.1016/j.scriptamat.2003.11.052 ↗
6. Light emission, chip morphology, and burr formation in drilling the bulk metallic glass10.1016/j.ijmachtools.2004.11.004 ↗
7. Investigation on chip deformation behaviors of Zr-based bulk metallic glass during machining10.1016/j.jmatprotec.2019.116404 ↗
8. Light emission of Zr-based bulk metallic glass during high-speed cutting: from generation mechanism to control strategies10.1016/j.jmatprotec.2022.117598 ↗
9. Investigations on surface microstructure in high-speed milling of Zr-based bulk metallic glass10.1016/j.jmapro.2018.07.020 ↗
10. Investigation of the softening behavior in severely deformed micromachined sub-surface of Zr-based bulk metallic glass via nanoindentation10.1016/j.jnoncrysol.2021.121280 ↗
11. Investigation of a novel sub-surface work hardening phenomenon in micro-turning of Zr-based bulk metallic glass10.1016/j.intermet.2022.107690 ↗
12. Understanding the abnormal effects of ultrasonic vibration on tool wear and surface generation in Zr-based bulk metallic glass cutting10.1016/j.cirpj.2022.07.004 ↗
13. In-situ tool wear area evaluation in micro milling with considering the influence of cutting force10.1016/j.ymssp.2021.107971 ↗
14. The influence of tool wear on the chip-forming mechanism and tool vibrations
15. An analysis of the residual stresses generated in Inconel 718™ when turning10.1016/j.jmatprotec.2005.12.007 ↗
16. Modeling of plastic deformation induced by thermo-mechanical stresses considering tool flank wear in high-speed machining Ti-6Al-4V10.1016/j.ijmecsci.2018.02.031 ↗
17. Investigations of new bulk metallic glass alloys fabricated using a high-pressure die-casting method based on industrial grade Zr raw material10.1016/j.jallcom.2019.03.357 ↗
18. Twinned-serrated chip formation with minor shear bands in ultra-precision micro-cutting of bulk metallic glass10.1007/s00170-020-04977-9 ↗
19. Rate dependency of a Zr-based bulk metallic glass: strength and fracture characteristic10.1016/j.matlet.2018.01.020 ↗
20. Formation of leaf-shaped microstructure on Zr-based metallic glass via nanosecond pulsed laser irradiation10.1016/j.jmapro.2021.10.016 ↗
21. Grinding performance and wear of metal bond super-abrasive tools in grinding of Zr-based bulk metallic glass10.1016/j.ijrmhm.2021.105501 ↗
22. Bulk metallic glasses10.1016/j.mser.2004.03.001 ↗
23. Adhering layer formation and its effect on the wear of coated carbide tools during turning of a nickel-based alloy10.1016/j.wear.2011.02.018 ↗
24. Nanocrystallization of Zr41.2Ti13.8Cu12.5Ni10.0Be22.5 metallic glass10.1016/j.actamat.2004.05.038 ↗
25. Effect of Nb on the glass-forming ability of mechanically alloyed Fe–Ni–Zr–B alloys10.1016/j.scriptamat.2007.11.004 ↗
26. Formation mechanism of lamellar chips during machining of bulk metallic glass10.1016/j.actamat.2009.02.031 ↗
27. Prediction of shear-band thickness in metallic glasses10.1016/j.scriptamat.2009.02.039 ↗
28. The nature and properties of amorphous matter
29. Wear mechanisms of WC/Co tools when machining high-strength titanium alloy TB6 (Ti-10V-2Fe-3Al)10.1007/s00170-016-9607-z ↗
30. Modelling of orthogonal cutting with a temperature dependent friction law10.1016/S0022-5096(98)00032-5 ↗
31. Origin of stress overshoot in amorphous solids10.1016/j.mechmat.2014.10.002 ↗