Microstructure and mechanical properties of novel Zr–Al–V alloys processed by hot rolling
Source abstract
Abstract
Abstract In this study, the effects of vanadium (V) addition on the microstructures and mechanical properties of hot-rolled Zr–9Al–χV alloys (χ = 0, 2 and 4 at. %) were systematically investigated. Microscopic analyses indicated that the microstructures of hot-rolled Zr–9Al–χV alloys were sensitive to the V content. The hot-rolled Zr–9Al alloy was completely dynamically recrystallized and consisted of the α phase only, whereas the hot-rolled Zr–9Al–2V alloy consisted of partially recrystallized α and transformed β (α′ + β). The tensile tests showed that the difference between the ultimate and yield strengths of the hot-rolled Zr–9Al alloy approximated 20 MPa, whereas that of the hot-rolled Zr–9Al–2V alloy was about 200 MPa. The evident strain hardening of the hot-rolled Zr–9Al–2V alloy was caused by the mechanical contrast between the soft and hard components of the microstructure. The hot-rolled Zr–9Al–4V alloy consisted of large elongated β grains, in which equiaxed α and acicular α" grains were distributed. The engineering stress–strain curve of the hot-rolled Zr–9Al–4V alloy exhibited a double-yielding behaviour, which was caused by stress-induced martensite phase transformation: β→α".
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Nuclear Materials and Properties · Titanium Alloys Microstructure and Properties · Fusion materials and technologies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (37)
Show source-provided references
1. Cryo-rolling enhanced inhomogeneous deformation and recrystallization grain growth of a zirconium alloy10.1016/j.jallcom.2016.12.300 ↗
2. Materials challenges in nuclear energy10.1016/j.actamat.2012.11.004 ↗
3. Effect of low-temperature pre-deformation on precipitation behavior and microstructure of a Zr-Sn-Nb-Fe-Cu-O alloy during fabrication10.1080/00223131.2015.1059776 ↗
4. Microstructure and mechanical properties of as-cast Zr–Nb alloys10.1016/j.actbio.2011.07.020 ↗
5. Microstructure and mechanical properties of hot-rolled ZrB alloys10.1016/j.msea.2015.01.052 ↗
6. Rudling · 2011
7. Mukhopadhyay · 2010
8. The Ti−Zr (titanium–zirconium) system10.1007/BF02881478 ↗
9. The Hf−Zr (hafnium−zirconium) system10.1007/BF02873408 ↗
10. The O−Zr (oxygen–zirconium) system10.1007/BF02881546 ↗
11. The Sc–Zr (scandium–zirconium) system10.1007/BF02663675 ↗
12. The orthorhombic α" martensite transformation during water quenching and its influence on mechanical properties of Ti–41Zr–7.3Al alloy10.1016/j.intermet.2014.03.010 ↗
13. Solid solution strengthening in Ti–Al alloys10.1007/BF02644529 ↗
14. New insights into perovskite-Ti3AlC precipitate splitting in a Ti–45Al–5Nb–0.75C alloy by transmission electron microscopy10.1016/j.intermet.2018.06.006 ↗
15. Abnormal β-phase stability in TiZrAl alloys10.1016/j.jallcom.2016.12.373 ↗
16. First-principles calculations and thermodynamic modeling of the V–Zr system10.1016/j.calphad.2011.07.003 ↗
17. Microstructural investigation of stress-assisted α"–α′ phase transformation in cold-rolled Ti–7.5Mo alloy10.1016/j.micron.2014.04.005 ↗
18. The Al–Zr (aluminum–zirconium) system10.1007/BF02667556 ↗
19. Dynamic-coarsening behavior of an α/β titanium alloy10.1007/s11661-006-1091-x ↗
20. Mechanisms of globularization of Ti–6Al–4V during static heat treatment10.1007/s11661-003-0103-3 ↗
21. Alpha/beta heat treatment of a titanium alloy with a nonuniform microstructure10.1007/s11661-007-9088-7 ↗
22. Low-temperature coarsening and plastic flow behavior of an alpha/beta titanium billet material with an ultrafine microstructure10.1007/s11661-008-9650-y ↗
23. Crystallographic variant selection in Ti–6Al–4V10.1016/j.actamat.2004.07.034 ↗
24. Microstructure and magnetic susceptibility of as-cast Zr–Mo alloys10.1016/j.actbio.2009.09.013 ↗
25. Effect of Zr, Sn and Al additions on deformation mode and beta phase stability of metastable beta Ti alloys10.2355/isijinternational.31.807 ↗
26. Strain rate-induced plasticity in bcc β-Ti alloy single crystal micropillars containing brittle ω-precipitates10.1016/j.matdes.2017.10.036 ↗
27. Effects of alloyed Si on the autoclave corrosion performance and periodic corrosion kinetics in Zr-Sn-Nb-Fe-O alloys10.1016/j.corsci.2015.08.043 ↗
28. Hierarchical 3D nanolayered duplex-phase Zr with high strength, strain hardening, and ductility10.1103/PhysRevLett.122.255501 ↗
29. Fatigue properties of a metastable β-type titanium alloy with reversible phase transformation10.1016/j.actbio.2007.09.009 ↗
30. Micromechanical behavior and thermal stability of a dual-phase α + α′ titanium alloy produced by additive manufacturing10.1016/j.actamat.2018.09.050 ↗
31. Heterogeneous lamella structure unites ultrafine-grain strength with coarse-grain ductility10.1073/pnas.1517193112 ↗
32. Enhanced strength and ductility in a high-entropy alloy via ordered oxygen complexes10.1038/s41586-018-0685-y ↗
33. Precipitation behavior and mechanical properties of Ti–Ni–Nb–Co alloys10.1016/j.intermet.2018.01.014 ↗
34. Effect of Sn and Zr addition on the martensitic transformation behavior of Ti–Mo shape memory alloys10.1016/j.jallcom.2016.10.108 ↗
35. Microstructure and martensitic transformation of TiNiNbB shape memory alloys10.1016/j.intermet.2015.04.013 ↗
36. On the origin of intergranular fracture in β phase shape memory alloys10.1016/0036-9748(82)90167-3 ↗
37. Intergranular fracture prediction and microstructure design10.1007/s10704-019-00347-z ↗