Deformation and fracture behavior of the novel NiAl alloy sheet with bimodal laminated structure by in-situ reaction synthesis
Source abstract
Abstract
Abstract Due to the intrinsic brittleness of NiAl alloy, its sheets are difficult to fabricate with traditional casting and rolling methods. To solve this problem, a novel NiAl alloy sheet with a special bimodal laminated structure was successfully designed and fabricated via the in-situ solid-state reaction synthesis using pure Ni and Al foils. The mechanical properties of the bimodal laminated NiAl alloy sheet were tested by hot tensile tests at temperatures ranging from 850 °C to 1000 °C and strain rates ranging from 0.01/s to 0.0005/s. To clarify the deformation mechanism, the deformation microstructure was characterized by scanning electron microscopy and electron backscatter diffraction technology. The fracture behavior was characterized by a three dimensional X-ray microscope. It was found that the sheet with the bimodal laminated structure composed of overlapped coarse-grained layers (CGLs) and fine-grained layers (FGLs) exhibits a significant deformation incompatibility between CGLs and FGLs, leading to a special deformation and fracture behavior. During hot deformation, dislocations mainly accommodate in FGLs at the beginning, and the coarse grains then begin to play a major role in replacing the privilege of FGLs and vital in storing dislocations during further deformation. The bimodal laminated grains are broken up into many fragments and the average grain sizes are refined after deformation due to the transformation of low angle boundaries into high angle boundaries. The nucleation of dynamic recrystallization grains preferentially takes place in FGLs, and DRX will occur in CGLs when sufficient strain and storage energy are accumulated. The fracture surface demonstrates a jagged fracture pattern parallel to the loading direction, which results from the special laminated grain structure. The fracture morphology along the thickness direction experiences dramatic changes related to the non-uniform strain distribution, which presented as the density and size distribution of voids in 3D space. The study is vital to guiding the high temperature forming and service performance of NiAl alloy.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Intermetallics and Advanced Alloy Properties · Metallic Glasses and Amorphous Alloys · Aluminum Alloys Composites Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (28)
Show source-provided references
1. Review: reaction synthesis processing of Ni-Al intermetallic materials10.1016/S0921-5093(00)01407-6 ↗
2. Producing laminated NiAl with bimodal distribution of grain size by solid–liquid reaction treatment10.1016/j.msea.2013.10.038 ↗
3. Mechanical properties of ( Ti2AlC+Ti3AlC ) - TiAl ceramic - intermetallic laminate ( CIL ) composites10.1016/j.msea.2013.07.076 ↗
4. A study on the orientation inheritance in laminated NiAl produced by in situ reaction annealing10.1016/j.micron.2016.01.006 ↗
5. Ni/Al multilayers producedby accumulative roll bondingand sputtering10.1007/s11665-016-2304-0 ↗
6. Mechanical properties and deformation behavior of laminated Ni - ( Ni2Al3+NiAl3 ) and Ni - ( Ni3Al+NiAl) composites10.1016/j.msea.2013.08.002 ↗
7. Superplasticity of stoichiometric NiAl with large grains10.1016/j.intermet.2004.07.008 ↗
8. EBSD investigation on the evolution of microstructure and grain boundaries in coarse-grained Ni-48Al upon large deformation at elevated temperature10.1016/j.intermet.2014.12.003 ↗
9. Superplasticity of single phase Ni-42Al intermetallics with large grains10.1016/j.msea.2006.08.011 ↗
10. Hot deformation behavior of Zr-1Nb alloy in two-phase region - microstructure and mechanical properties10.1016/j.jallcom.2018.01.008 ↗
11. Influence of hot - working conditions on grain growth of superalloy 71810.1016/j.jmatprotec.2018.12.002 ↗
12. The synergy effect of fine and coarse grains on enhanced ductility of bimodal-structured Mg alloys10.1016/j.jallcom.2018.11.229 ↗
13. Microstructure, texture and hardness of Al-Cu-Li alloy sheet during hot gas forming with integrated heat treatment10.1016/j.matdes.2016.01.001 ↗
14. γ-Phase transformation, dynamic recrystallization and texture of a forged TiAl-based alloy based on plane strain compression at elevated temperature10.1016/j.matdes.2015.11.120 ↗
15. Formability and microstructure evolution mechanisms of Ti6Al4V alloy during a novel hot stamping process10.1016/j.msea.2018.02.038 ↗
16. Strain-dependent constitutive equations to predict high temperature flow behavior of AA2030 aluminum alloy10.1016/j.mechmat.2016.06.018 ↗
17. Mechanism of saturated flow stress during hot tensile deformation of a TA15 Ti alloy10.1016/j.matdes.2015.07.100 ↗
18. Dynamic precipitation behavior before dynamic recrystallization in a Mg-Zn-Mn alloy during hot compression10.1016/j.matchar.2019.04.041 ↗
19. Microstructural characteristics and dynamic recrystallization behavior of β-γ TiAl based alloy during high temperature deformation10.1016/j.intermet.2018.04.002 ↗
20. Yu · 2013
21. Hall-Petch relation and boundary strengthening10.1016/j.scriptamat.2004.06.002 ↗
22. The operative slip system and general plasticity of NiAl-Ⅱ10.1016/0001-6160(66)90173-8 ↗
23. High temperature deformation of NiAl matrix composites10.1016/S1359-6454(99)00146-9 ↗
24. Deformation behavior of multilayered NiFe with bimodal grain size distribution at room and elevated temperature10.1016/j.msea.2015.12.075 ↗
25. Role of layered structure in ductility improvement of layered Ti-Al metal composite10.1016/j.actamat.2018.05.005 ↗
26. Microstructure, plastic deformation and strengthening mechanisms of an Al-Mg-Si alloy with a bimodal grain structure10.1016/j.jallcom.2015.01.229 ↗
27. Mechanical behavior and microstructure of a thermally stable bulk nanostructured Al alloy10.1007/s11661-001-0207-6 ↗
28. Deformation behavior of bimodal nanostructured 5083 Al alloys10.1007/s11661-005-0289-7 ↗