Embrittlement after high-temperature exposure to air of a near-γ TiAl alloy
Source abstract
Abstract
The loss of ductility of a Ti–48Al–2Cr–2Nb (at%) near-γ alloy after exposure to 80 % Ar–20 % O 2 at 700 °C for 1 h and 100 h has been investigated. In addition to marked decreases in ductility classically reported, increases in yield stress reaching +25 % have been observed. SIMS depth profiles enabled the determination of the 18 O isotope penetration depth via volume diffusion, which reached about 10 μm after 100 h of exposure. Site-specific lift–out by FIB, along with EBSD and TEM characterizations, were employed to examine the local transformations occurring in the diffusion zone and within the volume of exposed tensile specimens. In-situ TEM straining experiments were carried out on exposed and un-exposed specimens to study the influence of exposure on the microscopic mechanisms occurring in the bulk material. Results revealed the formation of chromium-rich precipitates and a recrystallized zone extending up to a depth of 15 μm from the surface after exposure. The dislocations in the subsurface layer were non-linear, likely due interactions between dislocation lines and oxygen solutes from the exposure atmosphere which potentially contribute to strengthening of the subsurface layer and ultimately to premature failure in this region. The elevated scattering in the in-situ TEM data did not allow to correlate the dislocation jump distances to the increase in yield stress.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Intermetallics and Advanced Alloy Properties · Titanium Alloys Microstructure and Properties · Metallurgical and Alloy Processes
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (38)
Show source-provided references
1. Advanced intermetallic TiAl alloys10.4028/www.scientific.net/MSF.879.113 ↗
2. TiAl alloys in commercial aircraft engines10.1080/09603409.2016.1183068 ↗
3. Wrought TiAl blades10.1016/j.matpr.2015.05.024 ↗
4. Gammalloy materials–processes–application technology
5. Development of gamma titanium aluminide (γ-TiAl) alloys: a review10.1016/j.jallcom.2022.167262 ↗
6. Advances in gamma titanium aluminides and their manufacturing techniques10.1016/j.paerosci.2012.04.001 ↗
7. Forged Intermetallic γ‐TiAl based alloy low pressure turbine blade in the geared turbofan
8. The science, technology, and implementation of TiAl alloys in commercial aircraft engines10.1557/opl.2013.44 ↗
9. High temperature materials for aerospace applications: Ni-based superalloys and γ-TiAl alloys10.1016/j.crhy.2018.10.002 ↗
10. Thénot · 2022
11. Effects of exposure at 700°C on RT tensile properties in a PM γ-TiAl alloy10.1016/j.intermet.2005.12.017 ↗
12. The effect of long term exposure in oxidising and corroding environments on the tensile properties of two gamma-TiAl alloys10.1016/j.intermet.2005.04.015 ↗
13. Effect of exposure on the mechanical properties of Gamma MET PX10.1016/j.intermet.2004.12.015 ↗
14. Environmental embrittlement of a third generation γ TiAl alloy10.1016/j.intermet.2011.10.006 ↗
15. Oxidation-induced embrittlement of TiAl alloys10.1016/j.intermet.2009.01.010 ↗
16. Effect of elevated temperature exposure on cast gamma titanium aluminide (Ti-48Al-2Cr-2Nb)10.1016/0956-716X(94)90322-0 ↗
17. Influence of a fine-grained surface structure on the tensile behaviour of a beta stabilised intermetallic γ-TiAl-based alloy10.1016/j.intermet.2022.107566 ↗
18. Reducing the environmental embrittlement effect of TiAl alloys exposed to air at high temperatures by a fine-grained surface structure10.1016/j.intermet.2024.108479 ↗
19. Depth resolved near-surface residual stresses in γ-based TiAl before and after high-temperature exposure10.1016/j.intermet.2016.12.014 ↗
20. Interactions of oxygen with intrinsic defects in L1 0 γ -TiAl in presence of substitutional solutes: influence on diffusion kinetics10.1016/j.commatsci.2021.110933 ↗
21. Relative effects of chromium and niobium on microstructure and mechanical properties as a function of oxygen content in TiAl alloys10.1016/j.scriptamat.2006.11.024 ↗
22. Effects of interstitial oxygen on microstructure and mechanical properties of Ti-48Al-2Cr-2Nb with fully lamellar and duplex microstructures10.1007/BF02586211 ↗
23. The effect of high temperature exposure on the tensile properties of γ TiAl alloys10.1016/S0966-9795(03)00116-X ↗
24. Laser directed energy deposited Ti-48Al-2Cr-2Nb alloy: an investigation of high temperature oxidation behavior10.1016/j.matlet.2024.136078 ↗
25. Oxygen diffusion coefficient in the γ phase of a TiAl GE alloy determined by SIMS10.1016/j.intermet.2024.108367 ↗
26. An in-situ study of ordinary dislocation glide in γ-TiAl alloys10.1080/01418619908210404 ↗
27. Farenc · 1992
28. An in-situ study of prismatic glide in alpha- titanium at low-temperatures10.1016/0956-7151(93)90139-J ↗
29. First-principles calculations of oxygen diffusion in Ti-Al alloys
30. Theoretical study of oxygen insertion and diffusivity in the γ-TiAl L10 system10.1088/1361-648X/ab6a2f ↗
31. Diffusion properties of oxygen in the γ-TiAl alloy10.1134/S1063776120030115 ↗
32. First-principle study of the solubility and diffusion of oxygen and boron in γ-TiAl10.1016/j.commatsci.2019.109475 ↗
33. Interaction of dislocations and interstitial solute in γ-TiAl10.1080/01418619808224075 ↗
34. Effects of oxygen on the deformation behaviour in single-phase γ-TiAl alloys10.1080/09500839408240977 ↗
35. Deformation mechanisms in the intermetallic compound TiAl10.1080/01418619008235562 ↗
36. Deformation modes and size effect in near-γ TiAl alloys10.1016/j.msea.2016.09.092 ↗
37. Extrinsic obstacles and loop formation in deformed metals and alloys10.1080/14786435.2012.705912 ↗
38. The geometry and nature of pinning points of ½ ⟨110] unit dislocations in binary TiAl alloys10.1080/01418619708200010 ↗