High-energy lithium metal pouch cells with limited anode swelling and long stable cycles
Source abstract
Abstract
Lithium metal anodes have attracted much attention as candidates for high-energy batteries, but there have been few reports of long cycling behaviour, and the degradation mechanism of realistic high-energy Li metal cells remains unclear. Here, we develop a prototypical 300 Wh kg−1 (1.0 Ah) pouch cell by integrating a Li metal anode, a LiNi0.6Mn0.2Co0.2O2 cathode and a compatible electrolyte. Under small uniform external pressure, the cell undergoes 200 cycles with 86% capacity retention and 83% energy retention. In the initial 50 cycles, flat Li foil converts into large Li particles that are entangled in the solid-electrolyte interphase, which leads to rapid volume expansion of the anode (cell thickening of 48%). As cycling continues, the external pressure helps the Li anode maintain good contact between the Li particles, which ensures a conducting percolation pathway for both ions and electrons, and thus the electrochemical reactions continue to occur. Accordingly, the solid Li particles evolve into a porous structure, which manifests in substantially reduced cell swelling by 19% in the subsequent 150 cycles. Much has been said about the high-energy, long-lasting potential of Li metal batteries, and yet little has been demonstrated at the cell scale. Here, Jun Liu and colleagues demonstrate a Li metal pouch cell with a 300 Wh kg−1 energy density and a 200-cycle lifetime.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advancements in Battery Materials · Advanced Battery Materials and Technologies · Advanced Battery Technologies Research
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (43)
Show source-provided references
1. Whittingham, M. S. Ultimate limits to intercalation reactions for lithium batteries. Chem. Rev. 114, 11414–11443 (2014).10.1021/cr5003003 ↗
2. Thackeray, M. M., Wolverton, C. & Isaacs, E. D. Electrical energy storage for transportation—approaching the limits of, and going beyond, lithium-ion batteries. Energy Environ. Sci. 5, 7854–7863 (2012).10.1039/c2ee21892e ↗
3. Pang, Q., Liang, X., Kwok, C. Y. & Nazar, L. F. Advances in lithium–sulfur batteries based on multifunctional cathodes and electrolytes. Nat. Energy 1, 16132 (2016).10.1038/nenergy.2016.132 ↗
4. Lv, D. et al. High performance Li-ion sulfur batteries enabled by intercalation chemistry. Chem. Commun. 51, 13454–13457 (2015).10.1039/C5CC05171A ↗
5. Zhang, J.-G., Xiao, J. & Xu, W. in The Lithium Air Battery: Primary Lithium Air Batteries 1st edn (eds Imanishi, N., Luntz, A. C. & Bruce, P.) Ch.10 (Springer, 2014).10.1007/978-1-4899-8062-5_10 ↗
6. Lu, D. et al. Formation of reversible solid electrolyte interface on graphite surface from concentrated electrolytes. Nano Lett. 17, 1602–1609 (2017).10.1021/acs.nanolett.6b04766 ↗
7. Liang, X. et al. A facile surface chemistry route to a stabilized lithium metal anode. Nat. Energy 2, 17119 (2017).10.1038/nenergy.2017.119 ↗
8. Wu, B. et al. Interfacial behaviours between lithium ion conductors and electrode materials in various battery systems. J. Mater. Chem. A 4, 15266–15280 (2016).10.1039/C6TA05439K ↗
9. Wang, H. et al. A reversible dendrite-free high-areal-capacity lithium metal electrode. Nat. Commun. 8, 15106 (2017).10.1038/ncomms15106 ↗
10. Pan, H. et al. Non-encapsulation approach for high-performance Li–S batteries through controlled nucleation and growth. Nat. Energy 2, 813–820 (2017).10.1038/s41560-017-0005-z ↗
11. Wood, K. N., Noked, M. & Dasgupta, N. P. Lithium metal anodes: toward an improved understanding of coupled morphological, electrochemical, and mechanical behavior. ACS Energy Lett. 2, 664–672 (2017).10.1021/acsenergylett.6b00650 ↗
12. Lu, D. et al. Failure mechanism for fast-charged lithium metal batteries with liquid electrolytes. Adv. Energy Mater. 5, 1400993 (2015).10.1002/aenm.201400993 ↗
13. Xiao, J. et al. Interplay between two-phase and solid solution reactions in high voltage spinel cathode material for lithium ion batteries. J. Power Sources 242, 736–741 (2013).10.1016/j.jpowsour.2013.05.148 ↗
14. Li, X. et al. Mesoporous silicon sponge as an anti-pulverization structure for high-performance lithium-ion battery anodes. Nat. Commun. 5, 4105 (2014).10.1038/ncomms5105 ↗
15. Kim, M. S. et al. Langmuir–Blodgett artificial solid-electrolyte interphases for practical lithium metal batteries. Nat. Energy 3, 889–898 (2018).10.1038/s41560-018-0237-6 ↗
16. Madec, L. et al. Effect of sulfate electrolyte additives on LiNi1/3Mn1/3Co1/3O2/graphite pouch cell lifetime: correlation between XPS surface studies and electrochemical test results. J. Phys. Chem. C 118, 29608–29622 (2014).10.1021/jp509731y ↗
17. Self, J., Aiken, C. P., Petibon, R. & Dahn, J. R. Survey of gas expansion in Li-ion NMC pouch cells. J. Electrochem. Soc. 162, A796–A802 (2015).10.1149/2.0081506jes ↗
18. Samba, A. et al. Impact of tab location on large format lithium-ion pouch cell based on fully coupled tree-dimensional electrochemical-thermal modeling. Electrochim. Acta 147, 319–329 (2014).10.1016/j.electacta.2014.08.115 ↗
19. Kumar, A. et al. Communication—indentation of Li-ion pouch cell: effect of material homogenization on prediction of internal short circuit. J. Electrochem. Soc. 163, A2494–A2496 (2016).10.1149/2.0151613jes ↗
20. Bond, T., Zhou, J. & Cutler, J. Electrode stack geometry changes during gas evolution in pouch-cell-type lithium ion batteries. J. Electrochem. Soc. 164, A6158–A6162 (2017).10.1149/2.0241701jes ↗
21. Cheng, X.-B. et al. The gap between long lifespan Li–S coin and pouch cells: the importance of lithium metal anode protection. Energy Storage Mater. 6, 18–25 (2017).10.1016/j.ensm.2016.09.003 ↗
22. Dixon, B., Mason, A. & Sahraei, E. Effects of electrolyte, loading rate and location of indentation on mechanical integrity of Li-ion pouch cells. J. Power Sources 396, 412–420 (2018).10.1016/j.jpowsour.2018.06.042 ↗
23. Hagen, M. et al. Lithium–sulfur cells: the gap between the state-of-the-art and the requirements for high energy battery cells. Adv. Energy Mater. 5, 1401986 (2015).10.1002/aenm.201401986 ↗
24. Nelson, K. J., Harlow, J. E. & Dahn, J. R. A comparison of NMC/graphite pouch cells and commercially available LiCoO2/graphite pouch cells tested to high potential. J. Electrochem. Soc. 165, A456–A462 (2018).10.1149/2.0041803jes ↗
25. Genovese, M. et al. Combinatorial methods for improving lithium metal cycling efficiency. J. Electrochem. Soc. 165, A3000–A3013 (2018).10.1149/2.0401813jes ↗
26. Muenzel, V. et al. A comparative testing study of commercial 18650-format lithium-ion battery cells. J. Electrochem. Soc. 162, A1592–A1600 (2015).10.1149/2.0721508jes ↗
27. Sahraei, E., Hill, R. & Wierzbicki, T. Calibration and finite element simulation of pouch lithium-ion batteries for mechanical integrity. J. Power Sources 201, 307–321 (2012).10.1016/j.jpowsour.2011.10.094 ↗
28. Bai, P., Li, J., Brushett, F. R. & Bazant, M. Z. Transition of lithium growth mechanisms in liquid electrolytes. Energy Environ. Sci. 9, 3221–3229 (2016).10.1039/C6EE01674J ↗
29. Zhang, S. S. Problem, status, and possible solutions for lithium metal anode of rechargeable batteries. ACS Appl. Energy Mater. 1, 910–920 (2018).10.1021/acsaem.8b00055 ↗
30. Xu, W. et al. Lithium metal anodes for rechargeable batteries. Energy Environ. Sci. 7, 513–537 (2014).10.1039/C3EE40795K ↗
31. Jiao, S. et al. Behavior of lithium metal anodes under various capacity utilization and high current density in lithium metal batteries. Joule 2, 110–124 (2018).10.1016/j.joule.2017.10.007 ↗
32. Wu, B. et al. The role of the solid electrolyte interphase layer in preventing Li dendrite growth in solid-state batteries. Energy Environ. Sci. 11, 1803–1810 (2018).10.1039/C8EE00540K ↗
33. Wu, B., Lochala, J., Taverne, T. & Xiao, J. The interplay between solid electrolyte interface (SEI) and dendritic lithium growth. Nano Energy 40, 34–41 (2017).10.1016/j.nanoen.2017.08.005 ↗
34. Chen, S. et al. High-efficiency lithium metal batteries with fire-retardant electrolytes. Joule 2, 1548–1558 (2018).10.1016/j.joule.2018.05.002 ↗
35. Chen, S. et al. High-voltage lithium-metal batteries enabled by localized high-concentration electrolytes. Adv. Mater. 30, 1706102 (2018).10.1002/adma.201706102 ↗
36. Mussa, A. S., Klett, M., Lindbergh, G. & Lindström, R. W. Effects of external pressure on the performance and ageing of single-layer lithium-ion pouch cells. J. Power Sources 385, 18–26 (2018).10.1016/j.jpowsour.2018.03.020 ↗
37. Barai, P., Higa, K. & Srinivasan, V. Impact of external pressure and electrolyte transport properties on lithium dendrite growth. J. Electrochem. Soc. 165, A2654–A2666 (2018).10.1149/2.0651811jes ↗
38. Yin, X. et al. Insights into morphological evolution and cycling behaviour of lithium metal anode under mechanical pressure. Nano Energy 50, 659–664 (2018).10.1016/j.nanoen.2018.06.003 ↗
39. Cannarella, J. & Arnold, C. B. Stress evolution and capacity fade in constrained lithium-ion pouch cells. J. Power Sources 245, 745–751 (2014).10.1016/j.jpowsour.2013.06.165 ↗
40. Kingery, W. D., Bowen, H. K. & Uhlmann, D. R. Introduction of Ceramics 2nd edn (Wiley, 1976).
41. Albertus, P., Babinec, S., Litzelman, S. & Newman, A. Status and challenges in enabling the lithium metal electrode for high-energy and low-cost rechargeable batteries. Nat. Energy 3, 16–21 (2018).10.1038/s41560-017-0047-2 ↗
42. Monroe, C. & Newman, J. The impact of elastic deformation on deposition kinetics at lithium/polymer interfaces. J. Electrochem. Soc. 152, A396–A404 (2005).10.1149/1.1850854 ↗
43. Lu, Z. et al. Nonfilling carbon coating of porous silicon micrometer-sized particles for high-performance lithium battery anodes. ACS Nano 9, 2540–2547 (2015).10.1021/nn505410q ↗