Visualization and suppression of interfacial recombination for high-efficiency large-area pin perovskite solar cells
Source abstract
Abstract
The performance of perovskite solar cells is predominantly limited by non-radiative recombination, either through trap-assisted recombination in the absorber layer or via minority carrier recombination at the perovskite/transport layer interfaces. Here, we use transient and absolute photoluminescence imaging to visualize all non-radiative recombination pathways in planar pin-type perovskite solar cells with undoped organic charge transport layers. We find significant quasi-Fermi-level splitting losses (135 meV) in the perovskite bulk, whereas interfacial recombination results in an additional free energy loss of 80 meV at each individual interface, which limits the open-circuit voltage (V) of the complete cell to ~1.12 V. Inserting ultrathin interlayers between the perovskite and transport layers leads to a substantial reduction of these interfacial losses at both the p and n contacts. Using this knowledge and approach, we demonstrate reproducible dopant-free 1 cm perovskite solar cells surpassing 20% efficiency (19.83% certified) with stabilized power output, a high V (1.17 V) and record fill factor (>81%).
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Perovskite Materials and Applications · Chalcogenide Semiconductor Thin Films · Quantum Dots Synthesis And Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (51)
Show source-provided references
1. Kojima, A., Teshima, K., Shirai, Y. & Miyasaka, T. Organometal halide perovskites as visible-light sensitizers for photovoltaic cells. J. Am. Chem. Soc. 131, 6050–6051 (2009).10.1021/ja809598r ↗
2. Kim, H. S. et al. Lead iodide perovskite sensitized all-solid-state submicron thin film mesoscopic solar cell with efficiency exceeding 9%. Sci. Rep. 2, 591 (2012).10.1038/srep00591 ↗
3. Lee, M. M., Teuscher, J., Miyasaka, T., Murakami, T. N. & Snaith, H. J. Efficient hybrid solar cells based on meso-superstructured organometal halide perovskites. Science 338, 643–647 (2012).10.1126/science.1228604 ↗
4. Yang, W. S. et al. Iodide management in formamidinium-lead-halide–based perovskite layers for efficient solar cells. Science 356, 1376–1379 (2017).10.1126/science.aan2301 ↗
5. Yoshikawa, K. et al. Silicon heterojunction solar cell with interdigitated back contacts for a photoconversion efficiency over 26%. Nat. Energy 2, 17032 (2017).10.1038/nenergy.2017.32 ↗
6. Tress, W. Perovskite solar cells on the way to their radiative efficiency limit—insights into a success story of high open-circuit voltage and low recombination. Adv. Energy Mater. 7, 1602358 (2017).10.1002/aenm.201602358 ↗
7. Grancini, G. et al. One-year stable perovskite solar cells by 2D/3D interface engineering. Nat. Commun. 8, 15684 (2017).10.1038/ncomms15684 ↗
8. Lin, Q., Nagiri, R. C. R., Burn, P. L. & Meredith, P. Considerations for upscaling of organohalide perovskite solar cells. Adv. Opt. Mater. 5, 1600819 (2017).10.1002/adom.201600819 ↗
9. Stolterfoht, M. et al. Approaching the fill factor Shockley–Queisser limit in stable, dopant-free triple cation perovskite solar cells. Energy Environ. Sci. 10, 1530–1539 (2017).10.1039/C7EE00899F ↗
10. Zhang, W. et al. Enhanced optoelectronic quality of perovskite thin films with hypophosphorous acid for planar heterojunction solar cells. Nat. Commun. 6, 10030 (2015).10.1038/ncomms10030 ↗
11. Zheng, X. et al. Defect passivation in hybrid perovskite solar cells using quaternary ammonium halide anions and cations. Nat. Energy 2, 17102 (2017).10.1038/nenergy.2017.102 ↗
12. Sherkar, T. S., Momblona, C., Gil-Escrig, L., Bolink, H. J. & Koster, L. J. A. Improving perovskite solar cells: Insights from a validated device model. Adv. Energy Mater. 7, 1602432 (2017).10.1002/aenm.201602432 ↗
13. Correa-Baena, J.-P. et al. Identifying and suppressing interfacial recombination to achieve high open-circuit voltage in perovskite solar cells. Energy Environ. Sci. 10, 1207–1212 (2017).10.1039/C7EE00421D ↗
14. Tvingstedt, K. et al. Removing leakage and surface recombination in planar perovskite solar cells. ACS Energy Lett. 2, 424–430 (2017).10.1021/acsenergylett.6b00719 ↗
15. Wolff, C. M. et al. Reduced interface-mediated recombination for high open-circuit voltages in CH3NH3PbI3 solar cells. Adv. Mater. 29, 1700159 (2017).10.1002/adma.201700159 ↗
16. Tan, H. et al. Efficient and stable solution-processed planar perovskite solar cells via contact passivation. Science 355, 722–726 (2017).10.1126/science.aai9081 ↗
17. Saliba, M. et al. Incorporation of rubidium cations into perovskite solar cells improves photovoltaic performance. Science 354, 206–209 (2016).10.1126/science.aah5557 ↗
18. Hou, Y. et al. A generic interface to reduce the efficiency–stability–cost gap of perovskite solar cells. Science 358, 1192–1197 (2017).10.1126/science.aao5561 ↗
19. Momblona, C. et al. Efficient vacuum deposited p-i-n and n-i-p perovskite solar cells employing doped charge transport layers. Energy Environ. Sci. 9, 3456–3463 (2016).10.1039/C6EE02100J ↗
20. Bush, K. A. et al. 23.6%-efficient monolithic perovskite/silicon tandem solar cells with improved stability. Nat. Energy 2, 17009 (2017).10.1038/nenergy.2017.9 ↗
21. Albrecht, S. et al. Monolithic perovskite/silicon-heterojunction tandem solar cells processed at low temperature. Energy Environ. Sci. 9, 81–88 (2016).10.1039/C5EE02965A ↗
22. Wu, Y. et al. Thermally stable MAPbI3 perovskite solar cells with efficiency of 19.19% and area over 1 cm2 achieved by additive engineering. Adv. Mater. 29, 170173 (2017).
23. Palma, A. L. et al. Laser-patterning engineering for perovskite solar modules with 95% aperture ratio. IEEE J. Photovolt. 7, 1674–1680 (2017).10.1109/JPHOTOV.2017.2732223 ↗
24. Staub, F. et al. Beyond bulk lifetimes: Insights into lead halide perovskite films from time-resolved photoluminescence. Phys. Rev. Appl. 6, 044017 (2016).10.1103/PhysRevApplied.6.044017 ↗
25. Richter, J. M. et al. Enhancing photoluminescence yields in lead halide perovskites by photon recycling and light out-coupling. Nat. Commun. 7, 13941 (2016).10.1038/ncomms13941 ↗
26. deQuilettes, D. W. et al. Photoluminescence lifetimes exceeding 8 μs and quantum yields exceeding 30% in hybrid perovskite thin films by ligand passivation. ACS Energy Lett. 1, 438–444 (2016).10.1021/acsenergylett.6b00236 ↗
27. Ahrenkiel, R. K. Minority-carrier lifetime in III–V semiconductors. Semicond. Semimet. 39, 39–150 (1993).10.1016/S0080-8784(08)62594-6 ↗
28. Herz, L. M. Charge-carrier mobilities in metal halide perovskites: Fundamental mechanisms and limits. ACS Energy Lett. 2, 1539–1548 (2017).10.1021/acsenergylett.7b00276 ↗
29. deQuilettes, D. W. et al. Photo-induced halide redistribution in organic–inorganic perovskite films. Nat. Commun. 7, 11683 (2016).10.1038/ncomms11683 ↗
30. Wurfel, P. The chemical potential of radiation. J. Phys. C 15, 3967–3985 (1982).10.1088/0022-3719/15/18/012 ↗
31. El-Hajje, G. et al. Quantification of spatial inhomogeneity in perovskite solar cells by hyperspectral luminescence imaging. Energy Environ. Sci. 131, 6050–6051 (2016).
32. Braly, I. L. & Hillhouse, H. W. Optoelectronic quality and stability of hybrid perovskites from MAPbI3 to MAPbI2Br using composition spread libraries. J. Phys. Chem. C. 120, 893–902 (2016).10.1021/acs.jpcc.5b10728 ↗
33. Sarritzu, V. et al. Optical determination of Shockley–Read–Hall and interface recombination currents in hybrid perovskites. Sci. Rep. 7, 44629 (2017).10.1038/srep44629 ↗
34. Johnston, S. & Unold, T. Correlations of Cu(In,Ga)Se2 imaging with device performance, defects, and microstructural properties. J. Vac. Sci. Technol. A 30, 4–9 (2012).10.1116/1.4714358 ↗
35. Bauer, G. H., Gütay, L. & Kniese, R. Structural properties and quality of the photoexcited state in Cu(In1−xGax)Se2 solar cell absorbers with lateral submicron resolution. Thin Solid Films 480–481, 259–263 (2005).10.1016/j.tsf.2004.11.029 ↗
36. Rau, U., Abou-Ras, D. & Kirchartz, T. (eds) Advanced Characterization Techniques for Thin Film Solar Cells (Wiley, Weinheim, 2011).10.1002/9783527636280 ↗
37. Tress, W. et al. Predicting the open-circuit voltage of CH3NH3PbI3 perovskite solar cells using electroluminescence and photovoltaic quantum efficiency spectra: the role of radiative and non-radiative recombination. Adv. Energy Mater. 5, 1400812 (2015).10.1002/aenm.201400812 ↗
38. Tvingstedt, K. et al. Radiative efficiency of lead iodide based perovskite solar cells. Sci. Rep. 4, 6071 (2014).10.1038/srep06071 ↗
39. Kirchartz, T. & Rau, U. Detailed balance and reciprocity in solar cells. Phys. Status Solidi A 205, 2737–2751 (2008).10.1002/pssa.200880458 ↗
40. Shockley, W. & Queisser, H. J. Detailed balance limit of efficiency of p-n junction solar cells. J. Appl. Phys. 32, 510–519 (1961).10.1063/1.1736034 ↗
41. Kirchartz, T., Staub, F. & Rau, U. Impact of photon recycling on the open-circuit voltage of metal halide perovskite solar cells. ACS Energy Lett. 1, 731–739 (2016).10.1021/acsenergylett.6b00223 ↗
42. Burgelman, M., Nollet, P. & Degrave, S. Modelling polycrystalline semiconductor solar cells. Thin Solid Films 362, 527–532 (2000).10.1016/S0040-6090(99)00825-1 ↗
43. Lee, J. et al. Achieving large-area planar perovskite solar cells by introducing an interfacial compatibilizer. Adv. Mater. 29, 1606363 (2017).10.1002/adma.201606363 ↗
44. Wang, Q., Dong, Q., Li, T., Gruverman, A. & Huang, J. Thin insulating tunneling contacts for efficient and water-resistant perovskite solar cells. Adv. Mater. 28, 6734–6739 (2016).10.1002/adma.201600969 ↗
45. Wu, Y. et al. Perovskite solar cells with 18.21% efficiency and area over 1 cm2 fabricated by heterojunction engineering. Nat. Energy 1, 16148 (2016).10.1038/nenergy.2016.148 ↗
46. Green, M. A. et al. Solar cell efficiency tables (version 51). Prog. Photovolt. Res. Appl. 26, 3–12 (2018).10.1002/pip.2978 ↗
47. Yang, W. S. et al. High-performance photovoltaic perovskite layers fabricated through intramolecular exchange. Science 348, 1234–1237 (2015).10.1126/science.aaa9272 ↗
48. Liu, T. et al. High-performance formamidinium-based perovskite solar cells via microstructure-mediated δ-to-α phase transformation. Chem. Mater. 29, 3246–3250 (2017).10.1021/acs.chemmater.7b00523 ↗
49. Yu, Y. et al. Improving the performance of formamidinium and cesium lead triiodide perovskite solar cells using lead thiocyanate additives. ChemSusChem 9, 3288–3297 (2016).10.1002/cssc.201601027 ↗
50. Delamarre, A., Lombez, L. & Guillemoles, J. F. Contactless mapping of saturation currents of solar cells by photoluminescence. Appl. Phys. Lett. 100, 131108 (2012).10.1063/1.3697704 ↗
51. Burkhard, G. F., Hoke, E. T. & McGehee, M. D. Accounting for interference, scattering, and electrode absorption to make accurate internal quantum efficiency measurements in organic and other thin solar cells. Adv. Mater. 22, 3293–3297 (2010).10.1002/adma.201000883 ↗