journal article·2024-06

Surface quality investigation in high-speed dry milling of Ti-6Al-4V by using 2D ultrasonic-vibration-assisted milling platform

Jin Zhang, Li Ling, Qian-Yue Wang, Xue-Feng Huang, Xin-Zhen Kang, Gui-Bao Tao, Hua-Jun Cao

Advances in Manufacturing· Volume 12· Issue 2
Publisher page

Abstract

Ultrasonic-vibration-assisted milling (UVAM) is an advanced method for the efficient and precise machining of difficult-to-machine materials in modern manufacturing. However, the milling efficiency is limited because the ultrasonic vibration toolholder ER16 collet has a critical cutting speed. Thus, a 2D UVAM platform is built to ensure precision machining efficiency and improve the surface quality without changing the milling toolholder. To evaluate this 2D UVAM platform, ultrasonic-vibration-assisted high-speed dry milling (UVAHSDM) is performed to process a titanium alloy (Ti-6Al-4V) on the platform, and the milling temperature, surface roughness, and residual stresses are selected as the important indicators for performance analysis. The results show that the intermittent cutting mechanism of UVAHSDM combined with the specific spindle speed, feed speed, and vibration amplitude can reduce the milling temperature and improve the texture of the machined surface. Compared with conventional milling, UVAHSDM reduces surface roughness and peak-groove surface profile values and extends the range of residual surface compressive stresses from −413.96 MPa to −600.18 MPa. The excellent processing performance demonstrates the feasibility and validity of applying this 2D UVAM platform for investigating surface quality achieved under UVAHSDM.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced machining processes and optimization · Advanced Machining and Optimization Techniques · Advanced Surface Polishing Techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (46)

Show source-provided references
1. Ulutan D, Ozel T (2011) Machining induced surface integrity in titanium and nickel alloys: a review. Int J Mach Tool Manuf 51(3):250–28010.1016/j.ijmachtools.2010.11.003 ↗
2. Liu HG, Zhang J, Xu X et al (2018) Experimental study on fracture mechanism transformation in chip segmentation of Ti-6Al-4V alloys during high-speed machining. J Mater Process Technol 257:132–14010.1016/j.jmatprotec.2018.02.040 ↗
3. Liang L, Liu ZQ (2018) Tool wear behaviors and corresponding machined surface topography during high-speed machining of Ti-6Al-4V with fine grain tools. Tribol Int 121:321–33210.1016/j.triboint.2018.01.057 ↗
4. Schulz H, Moriwaki T (1992) High speed machining. CIRP Ann 41(2):637–64310.1016/S0007-8506(07)63250-8 ↗
5. Khanna N, Davim JP (2015) Design-of-experiments application in machining titanium alloys for aerospace structural components. Measurement 61:280–29010.1016/j.measurement.2014.10.059 ↗
6. Liang XL, Liu ZQ, Wang B (2020) Dynamic recrystallization characterization in Ti-6Al-4V machined surface layer with process-microstructure-property correlations. Appl Surf Sci 530:147184. https://doi.org/10.1016/j.apsusc.2020.14718410.1016/j.apsusc.2020.147184 ↗
7. Wang B, Liu ZQ, Cai YK et al (2021) Advancements in material removal mechanism and surface integrity of high speed metal cutting: a review. Int J Mach Tool Manuf 166:103744. https://doi.org/10.1016/j.ijmachtools.2021.10374410.1016/j.ijmachtools.2021.103744 ↗
8. Marusich TD, Ortiz M (1995) Modelling and simulation of high-speed machining. Int J Numer Methods Eng 38(21):3675–369410.1002/nme.1620382108 ↗
9. Umbrello D (2008) Finite element simulation of conventional and high speed machining of Ti6Al4V alloy. J Mater Process Technol 196(1/3):79–8710.1016/j.jmatprotec.2007.05.007 ↗
10. Chen G, Ren CZ, Yang XY et al (2011) Finite element simulation of high-speed machining of titanium alloy (Ti-6Al-4V) based on ductile failure model. Int J Adv Manuf Technol 56(9/12):1027–103810.1007/s00170-011-3233-6 ↗
11. Zhang XY, Sui H, Zhang DY et al (2017) Feasibility study of high-speed ultrasonic vibration cutting titanium alloy. J Mech Eng 53(19):120–12710.3901/JME.2017.19.120 ↗
12. Wu XF, Li CH, Zhou ZM et al (2021) Circulating purification of cutting fluid: an overview. Int J Adv Manuf Technol 117(9/10):2565–260010.1007/s00170-021-07854-1 ↗
13. Wang XM, Li CH, Zhang YB et al (2022) Tribology of enhanced turning using biolubricants: a comparative assessment. Tribol Int 174:107766. https://doi.org/10.1016/j.triboint.2022.10776610.1016/j.triboint.2022.107766 ↗
14. Ni CB, Zhu LD (2020) Investigation on machining characteristics of TC4 alloy by simultaneous application of ultrasonic vibration assisted milling (UVAM) and economical-environmental MQL technology. J Mater Process Technol 278:116518. https://doi.org/10.1016/j.jmatprotec.2019.11651810.1016/j.jmatprotec.2019.116518 ↗
15. Yang X, Cao HJ, Chen YP et al (2015) Whole process cutting heat transfer model for highspeed dry hobbing. J Mech Eng 51(19):189–19610.3901/JME.2015.19.189 ↗
16. Chen YP, Cao HJ, Yang X (2017) Research on load distribution characteristic on the cutting edge in high speed gear hobbing process. J Mech Eng 53(15):181–18710.3901/JME.2017.15.181 ↗
17. Zhang H, Dang JQ, Ming WW et al (2020) Cutting responses of additive manufactured Ti6Al4V with solid ceramic tool under dry high-speed milling processes. Ceram Int 46(10):14536–1454710.1016/j.ceramint.2020.02.253 ↗
18. Liu MZ, Li CH, Cao HJ et al (2022) Research progresses and applications of CMQL machining technology. Chin J Mech Eng 33(5):529–550
19. Adithan M (1974) Tool wear studies in ultrasonic drilling. Wear 29(1):81–9310.1016/0043-1648(74)90136-7 ↗
20. Zhang LB, Wang LJ, Liu XY et al (2001) Mechanical model for predicting thrust and torque in vibration drilling fibre-reinforced composite materials. Int J Mach Tool Manuf 41(5):641–65710.1016/S0890-6955(00)00105-X ↗
21. Xu WX, Zhang LC (2015) Ultrasonic vibration-assisted machining: principle, design and application. Adv Manuf 3:173–19210.1007/s40436-015-0115-4 ↗
22. Chen WQ, Huo DH, Hale J et al (2018) Kinematics and tool-workpiece separation analysis of vibration assisted milling. Int J Mech Sci 136:169–17810.1016/j.ijmecsci.2017.12.037 ↗
23. Ding H, Ibrahim R, Cheng K et al (2010) Experimental study on machinability improvement of hardened tool steel using two dimensional vibration-assisted micro-end-milling. Int J Mach Tool Manuf 50(12):1115–111810.1016/j.ijmachtools.2010.08.010 ↗
24. Niu Y, Jiao F, Zhao B et al (2019) 3D finite element simulation and experimentation of residual stress in longitudinal torsional ultrasonic assisted milling. J Mech Eng 55(13):224–23210.3901/JME.2019.13.224 ↗
25. Chen P, Tong J, Zhao J et al (2020) A study of the surface microstructure and tool wear of titanium alloys after ultrasonic longitudinal-torsional milling. J Manuf Process 53:1–1110.1016/j.jmapro.2020.01.040 ↗
26. Qin S, Zhu L, Wiercigroch M et al (2022) Material removal and surface generation in longitudinal-torsional ultrasonic assisted milling. Int J Mech Sci 227:107375. https://doi.org/10.1016/j.ijmecsci.2022.10737510.1016/j.ijmecsci.2022.107375 ↗
27. Tong JL, Zhang ZP, Chen P et al (2022) Study on surface morphology of titanium alloy curved thin-walled parts by longitudinal-torsional composite ultrasonic assisted milling. J Manuf Process 84:316–32610.1016/j.jmapro.2022.09.049 ↗
28. Liu JJ, Jiang XG, Han X et al (2019) Effects of rotary ultrasonic elliptical machining for side milling on the surface integrity of Ti-6Al-4V. Int J Adv Manuf Technol 101:1451–146510.1007/s00170-018-2847-3 ↗
29. Zhang ML, Zhang DY, Geng DX et al (2020) Effects of tool vibration on surface integrity in rotary ultrasonic elliptical end milling of Ti-6Al-4V. J Alloys Compd 821:153266. https://doi.org/10.1016/j.jallcom.2019.15326610.1016/j.jallcom.2019.153266 ↗
30. Zhang ML, Zhang DY, Geng DX et al (2020) Surface and sub-surface analysis of rotary ultrasonic elliptical end milling of Ti-6Al-4V. Mater Des 191:108658. https://doi.org/10.1016/j.jallcom.2019.15326610.1016/j.jallcom.2019.153266 ↗
31. Chen WQ, Zheng L, Xie WK et al (2019) Modelling and experimental investigation on textured surface generation in vibration-assisted micro-milling. J Mater Process Technol 266:339–35010.1016/j.jmatprotec.2018.11.011 ↗
32. Gao T, Zhang XP, Li CH et al (2020) Surface morphology evaluation of multi-angle 2D ultrasonic vibration integrated with nanofluid minimum quantity lubrication grinding. J Manuf Process 51:44–6110.1016/j.jmapro.2020.01.024 ↗
33. Song DL, Zhao J, Ji SJ et al (2016) Development of a novel two-dimensional ultrasonically actuated polishing process. AIP Adv 6:115105. https://doi.org/10.1063/1.496729210.1063/1.4967292 ↗
34. Ni CB, Zhu LD, Liu CF et al (2018) Analytical modeling of tool-workpiece contact rate and experimental study in ultrasonic vibration-assisted milling of Ti-6Al-4V. Int J Mech Sci 142/143:97–11110.1016/j.ijmecsci.2018.04.037 ↗
35. Xie WB, Wang XK, Zhao B et al (2022) Surface and subsurface analysis of TC18 titanium alloy subject to longitudinal-torsional ultrasonic vibration-assisted end milling. J Alloys Compd 929:167259. https://doi.org/10.1016/j.jallcom.2022.16725910.1016/j.jallcom.2022.167259 ↗
36. Gao HH, Ma BJ, Zhu YP et al (2022) Enhancement of machinability and surface quality of Ti-6Al-4V by longitudinal ultrasonic vibration-assisted milling under dry conditions. Measurement 187:110324. https://doi.org/10.1016/j.measurement.2021.11032410.1016/j.measurement.2021.110324 ↗
37. Bhirud NL, Gawande RR (2017) Optimization of process parameters during end milling and prediction of work piece temperature rise. Arch Mech Eng 64(3):66. https://doi.org/10.1515/meceng-2017-002010.1515/meceng-2017-0020 ↗
38. Lee WJ, Park SH, Yoon HS (2022) A coolant supply strategy based on cutting temperature prediction during the 3-axis end-milling of Ti-6Al-4V. J Manuf Process 84:272–28110.1016/j.jmapro.2022.10.010 ↗
39. Li CP, Huang L, Xu MR et al (2022) Processing mechanism of electrical discharge-assisted milling titanium alloy based on 3D thermal-mechanical coupling cutting model. J Manuf Process 78:107–11910.1016/j.jmapro.2022.04.012 ↗
40. Feng YX, Hsu FC, Lu YT et al (2020) Temperature prediction of ultrasonic vibration-assisted milling. Ultrasonics 108:106212. https://doi.org/10.1016/j.ultras.2020.10621210.1016/j.ultras.2020.106212 ↗
41. Li SC, Xiao GJ, Chen BQ et al (2022) Surface formation modeling and surface integrity research of normal ultrasonic assisted flexible abrasive belt grinding. J Manuf Process 80:232–24610.1016/j.jmapro.2022.05.045 ↗
42. Chen T. Theory and methods of surface integrity in machining. China Science Publishing & Media Ltd, Beijing
43. Feng YX, Hsu FC, Lu YT et al (2020) Surface roughness prediction in ultrasonic vibration-assisted milling. J Adv Mech Des Syst 14(4):1–14
44. Peng ZL, Zhang XY, Zhang DY (2021) Improvement of Ti-6Al-4V surface integrity through the use of high-speed ultrasonic vibration cutting. Tribol Int 160:107025. https://doi.org/10.1016/j.triboint.2021.10702510.1016/j.triboint.2021.107025 ↗
45. Zhao WD, Liu DX, Chiang RC et al (2020) Effects of ultrasonic nanocrystal surface modification on the surface integrity, microstructure, and wear resistance of 300M martensitic ultra-high strength steel. J Mater Process Technol 285:116767. https://doi.org/10.1016/j.jmatprotec.2020.11676710.1016/j.jmatprotec.2020.116767 ↗
46. Feng YX, Hsu FC, Lu YT et al (2019) Residual stress prediction in ultrasonic vibration–assisted milling. Int J Adv Manuf Technol 104:2579–259210.1007/s00170-019-04109-y ↗