Application of grey relational analysis based on Taguchi method for optimizing machining parameters in hard turning of high chrome cast iron
Source abstract
Abstract
High chrome white cast iron is particularly preferred in the production of machine parts requiring high wear resistance. Although the amount of chrome in these materials provides high wear and corrosion resistances, it makes their machinability difficult. This study presents an application of the grey relational analysis based on the Taguchi method in order to optimize chrome ratio, cutting speed, feed rate, and cutting depth for the resultant cutting force (FR) and surface roughness (Ra) when hard turning high chrome cast iron with a cubic boron nitride (CBN) insert. The effect levels of machining parameters on FR and Ra were examined by an analysis of variance (ANOVA). A grey relational grade (GRG) was calculated to simultaneously minimize FR and Ra. The ANOVA results based on GRG indicated that the feed rate, followed by the cutting depth, was the main parameter and contributed to responses. Optimal levels of parameters were found when the chrome ratio, cutting speed, feed rate, and cutting depth were 12%, 100 m/min, 0.05 mm/r, and 0.1 mm, respectively, based on the multiresponse optimization results obtained by considering the maximum signal to noise (S/N) ratio of GRG. Confirmation results were verified by calculating the confidence level within the interval width.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced machining processes and optimization · Advanced Machining and Optimization Techniques · Metal Alloys Wear and Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (32)
Show source-provided references
1. Chung RJ, Tang X, Hinckley DYLB et al (2013) Microstructure refinement of hypereutetic high Cr cast iron using hard carbide-forming elements for improved wear resistance. Wear 301:695–70610.1016/j.wear.2013.01.079 ↗
2. Çetinkaya C (2006) An investigation of the wear behaviour of white cast irons under different compositions. Mater Des 27:437–44510.1016/j.matdes.2004.11.021 ↗
3. El-Aziz KA, Zohdy K, Saber D et al (2015) Wear and corrosion behavior of high-Cr white cast iron alloys in different corrosive media. J Bio Tribo Corros 1:2510.1007/s40735-015-0026-8 ↗
4. Sallam HEM, El-Aziz KA, El-Raouf HA et al (2013) Failure analysis and flexural behavior of high chromium white cast iron and AISI4140 Steel bimetal beams. Mater Des 52:974–98010.1016/j.matdes.2013.06.045 ↗
5. Günay M, Korkmaz ME, Yaşar N (2017) Finite element modeling of tool stresses on ceramic tools in hard turning. Mechanika 23(3):432–44010.5755/j01.mech.23.3.14363 ↗
6. Zhou JM, Andersson M, Stahl JE (2004) Identification of cutting error in precision hard turning process. J Mater Process Technol 153:746–75010.1016/j.jmatprotec.2004.04.331 ↗
7. Klocke F, Brinksmeier E, Weinert K (2005) Capabilty profile of hard cutting and grinding process. CIRP Ann Manuf Technol 54:22–4510.1016/S0007-8506(07)60018-3 ↗
8. Smith S, Melkote SN, Curzio EL et al (2007) Effect of surface integrity of hard turned AISI 52100 steel on fatigue performance. Mater Sci Eng A 459:337–34610.1016/j.msea.2007.01.011 ↗
9. Fallbohmer P, Rodriguez CA, Ozel T et al (2000) High-speed machining of cast iron and alloy steel for die and mould manufacturing. J Mater Process Technol 98:104–11510.1016/S0924-0136(99)00311-8 ↗
10. Aslan E, Camuscu N, Birgören B (2007) Design optimisation of cutting parameter when turning hardened AISI 4140 steel (63 HRC) with Al2O3 + TiCN mixed ceramic tool. Mater Des 28:1618–162210.1016/j.matdes.2006.02.006 ↗
11. Huang Y, Chou YK, Liang SY (2007) CBN tool wear in hard turning: a survey on research progresses. Int J Adv Manuf Technol 35:443–45310.1007/s00170-006-0737-6 ↗
12. Sing D, Rao PV (2006) A surface roughness prediction model for hard turning process. Int J Adv Manuf Technol 32:1115–112410.1007/s00170-006-0429-2 ↗
13. Çoğun C, Özses B (2002) Bilgisayar sayisal denetimli takim tazgahlarinda değişik işleme koşullarinin yüzey pürüzlülüğüne etkisi. J Fac Eng Arch Gazi Univ 17(1):59–75
14. Korkmaz ME, Günay M (2018) Finite element modelling of cutting forces and power consumption in turning of AISI 420 martensitic stainless steel. Arab J Sci Eng. https://doi.org/10.1007/s13369-018-3204-410.1007/s13369-018-3204-4 ↗
15. Bartarya G, Choudhury SK (2012) Effect of cutting parametes on cutting force and surface roughness during finish hard turning AISI52100 grade steel. Procedia CIRP 1:651–65610.1016/j.procir.2012.05.016 ↗
16. Rao CJ, Rao DN, Srihari P (2013) Influence of cutting parameters on cutting force and surface finish in turning operation. Procedia Eng 64:1405–141510.1016/j.proeng.2013.09.222 ↗
17. Rafai NH, Islam MN (2009) An investigation in to dimensional accuracy and surface finish achieveble in dry turning. Mach Sci Technol 13:571–58910.1080/10910340903451456 ↗
18. Bouacha K, Yallese MA, Mabrouki T et al (2010) Statistical analysis of surface roughness and cutting force using response surface methodology in hard turning of AISI 52100 bearing steel with CBN tool. Int J Refract Met Hard Mater 28:349–36110.1016/j.ijrmhm.2009.11.011 ↗
19. Chavoshi SZ, Tajdari M (2010) Surface roughness modelling in hard turning operation of AISI 4140 using CBN cutting tool. Int J Mater Form 3:233–23910.1007/s12289-009-0679-2 ↗
20. Masood SH, Armitage K, Brandt M (2011) An experimental study of laser-assisted machining of hard-to-wear white cast iron. Int J Mach Tool Manuf 51:450–45610.1016/j.ijmachtools.2011.02.001 ↗
21. Ravi AM, Murigendrappa SM, Mukunda PG (2014) Machinability investigation on high chrome white cast iron using multicoated hard carbide tools. Trans Indian Inst Met 67(4):485–50210.1007/s12666-013-0369-0 ↗
22. Jiang W, More AS, Brown WD et al (2006) A CBN-TiN composite coating for carbide insert: coating characterisation and its application for finish hard turning. Surf Coat Technol 201:2443–244910.1016/j.surfcoat.2006.04.026 ↗
23. Manivel D, Gandhinathan R (2016) Optimization of surface roughness and tool wear in hard turning of austempered ductile iron using Taguchi method. Meas 93:108–11610.1016/j.measurement.2016.06.055 ↗
24. Kır D, Öktem H, Çöl M et al (2016) Determination of the cutting tool performance of high-alloyed white cast iron (Ni-Hard 4) using the Taguchi method. Mater Technol 50(2):239–246
25. KYOCERA Precision Tools, Inc. http://www.kyoceraprecisiontools.com/indexable/pdf/Turning_Catalog_2017.pdf . Accessed 16 Jan 2017
26. Taguchi G, Chowdhury S, Wu Y (2004) Taguchi’s quality engineering handbook. Wiley, Hoboken10.1002/9780470258354 ↗
27. Sarıkaya M, Güllü A (2015) Multiresponse optimization of minimum quantity lubrication parameter using Taguchi-based grey relational analysis in turning of difficult-to-cut alloy Haynes 25. J Clean Prod 91:347–35710.1016/j.jclepro.2014.12.020 ↗
28. Deng JL (1989) Introduction to grey system theory. J Grey Syst 1:1–24
29. Sahoo AK, Sahoo B (2013) Performance studies of multilayer hard surface coating (TiN/TiCN/Al2O3/TiN) of indexeble carbide insert in hard machining: part-II (RSM, grey relational and techno economical approach). Measurement 46:2868–288410.1016/j.measurement.2012.09.023 ↗
30. Kalyon A, Özyürek D, Günay M et al (2015) Dry sliding wear behaviour of valve seat insert produced from high chromium white iron. High Temp Mater Process 34:635–64110.1515/htmp-2014-0110 ↗
31. Grzesik W, Rech J, Wanat T (2007) Surface finish on hardened bearing steel part produced by superhard and abrasive tools. Int J Mach Tools Manuf 47:255–26210.1016/j.ijmachtools.2006.03.018 ↗
32. Savaş V, Ozay C, Ballikaya H (2016) Experimental investigation of cutting parameter in machining of 100Cr6 with tangential turnmilling method. Adv Manuf 4:97–10410.1007/s40436-016-0134-9 ↗