AlB3 master alloy to grain refine AlSi10Mg and AlSi12Cu aluminium foundry alloys
Source abstract
Abstract
Abstract The potential of AlB3 master alloy in the grain refinement of AlSi10Mg and AlSi12Cu foundry alloys was investigated and compared with that of the AlTi5B1 master alloy, the standard grain refiner for most aluminium foundries. The latter refines the grain structures of both alloys. However, this performance is not nearly as good as that obtained in wrought aluminium alloys with the same grain refiner. The Ti-free AlSi10Mg and AlSi12Cu alloys, on the other hand, exhibit very small grains for the entire range of holding times when inoculated with AlB3. This implies a remarkable grain refining efficiency, typical of grain refined wrought aluminium alloys, as well as a strong resistance to fading of the grain refinement effect. Lack of Ti in the melt allows the entire B to form AlB2 particles, the perfect substrates, shortly before α-Al starts to crystallize. Aluminium castings can enjoy grains as small as those of the wrought alloys, well below 200 μm, with an addition of 0.02 wt% B provided that their Ti content is controlled.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Microstructure and mechanical properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (25)
Show source-provided references
1. Murty · Int. Mater. Rev. · 2002 · 47 · 310.1179/095066001225001049 ↗
2. Dahle · Mater. Sci. Forum · 2010 · 649 · 28710.4028/www.scientific.net/MSF.649.287 ↗
3. StJohn · Acta Mater. · 2011 · 59 · 490710.1016/j.actamat.2011.04.035 ↗
4. Birol · J. Alloys Compd. · 2006 · 420 · 20710.1016/j.jallcom.2005.11.010 ↗
5. Faraji · Mater. Lett. · 2010 · 64 · 101610.1016/j.matlet.2010.01.028 ↗
6. Cibula · J. Inst. Met. · 1949 · 76 · 321
7. Nie · J. Alloys Compd. · 2011 · 509 · 111910.1016/j.jallcom.2010.09.180 ↗
8. Birol · J. Alloys Compd. · 2006 · 420 · 7110.1016/j.jallcom.2005.10.017 ↗
9. Birol · J. Alloys Compd. · 2007 · 427 · 14210.1016/j.jallcom.2006.03.002 ↗
10. Greer · Adv. Eng. Mater. · 2003 · 5 · 8110.1002/adem.200390013 ↗
11. Easton · Metall. Mater. Trans. · 2005 · 36 · 191110.1007/s11661-005-0054-y ↗
12. Sigworth · AFS Trans. · 2007 · 115 · 1
13. Nafisi · Mater. Sci. Eng. · 2007 · A452–453 · 44510.1016/j.msea.2006.10.145 ↗
14. Y. Birol, Mater. Sci. Technol., doi:10.1179/1743284711Y.0000000031.10.1179/1743284711Y.0000000031 ↗
15. Mohanty · Acta Metall. Mater. · 1996 · 44 · 374910.1016/1359-6454(96)00021-3 ↗
16. Qiu · Acta Mater. · 2007 · 55 · 144710.1016/j.actamat.2006.09.046 ↗
17. Kori · Mater. Sci. Eng. A · 2000 · 283 · 9410.1016/S0921-5093(99)00794-7 ↗
18. Y. Birol, Mater. Sci. Technol., doi:10.1179/1743284711Y.0000000041.10.1179/1743284711Y.0000000041 ↗
19. Y. Birol, Mater. Sci. Technol., doi:10.1179/1743284711Y.0000000049.10.1179/1743284711Y.0000000049 ↗
20. Y. Birol, Mater. Sci. Technol., doi:10.1179/1743284711Y.0000000058.10.1179/1743284711Y.0000000058 ↗
21. Li · J. Alloys Compd. · 2010 · 503 · 28610.1016/j.jallcom.2010.04.251 ↗
22. Novak · Mater. Sci. Forum · 2011 · 690 · 4910.4028/www.scientific.net/MSF.690.49 ↗
23. Mallapur · J. Mater. Sci. · 2011 · 46 · 162210.1007/s10853-010-4977-3 ↗
24. Shabani · Mater. Des. · 2011 · 32 · 154210.1016/j.matdes.2010.09.035 ↗
25. Quested · Acta Mater. · 2005 · 53 · 132310.1016/j.actamat.2004.11.024 ↗