DIC-based experimental study of fracture toughness through R-curve tests in a multi-layered Al-Mg (LZ91) composite fabricated by ARB
Source abstract
Abstract
Abstract Adding Li to Mg, dual-phase Mg-Li with very low density and high formability at room temperature was produced and used as a reinforcement phase for fabricating a three-layered metal matrix Al-Mg composite through accumulative roll bonding (ARB) process. In this study, due to the inherent nature of the ARB process, which is associated with high strain, and low strength of the magnesium-lithium alloy, the fracture toughness test and energy absorption were used in addition to the tensile test to observe the interaction effect of the increasing strength and the reducing elongation, which were caused by the ARB. By preparing the compact tension (CT) specimens and conducting R-curve tests, the fracture behavior of the processed composite in various ARB cycles (primary sandwich and four ARB cycles) was investigated. Meanwhile, a Digital Image Correlation (DIC) system was also employed to measure the variation of crack growth, crack opening, and corresponding forces and increase the accuracy and quality of the results. The surrounded area under the force-displacement of crack opening curves was measured and calculated as the toughness and absorbed energy. Tensile strength and total elongation of the processed composite improved gradually, 275.7% and 38%, respectively, compared to the primary phase as the number of cycles increased and the thickness of the layers decreased. Plastic instability was more prominent in the last cycles because of the increasing trend of imposed strains and the reduction in thickness which reached their highest amounts at the final step. Although obtained results confirmed the general improvement in fracture toughness of the ARBed composite, its value varied slightly from one cycle to another. The highest values were achieved for total energy absorption and crack opening at maximum force after the second ARB cycle. In contrast, the maximum amount of fracture toughness, 29.08 MPa m1/2, was belonged to the last cycle of the process. Dimples and micro-cavities, seen in both SEM images of Al and Mg layers, resulted in a ductile failure.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloys Composites Properties · Metal Forming Simulation Techniques · Microstructure and mechanical properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (42)
Show source-provided references
1. Towards magnesium alloys for high-volume automotive applications10.1016/j.scriptamat.2016.07.035 ↗
2. Recent progress in magnesium-lithium alloys10.1179/1743280414Y.0000000044 ↗
3. Research and development in magnesium alloys for industrial and biomedical applications: a review10.1007/s12540-019-00346-8 ↗
4. The properties of some magnesium-lithium alloys containing aluminum and zinc10.1007/BF03399088 ↗
5. Mechanical property and fracture behavior of Al/Mg composite produced by Accumulative Roll Bonding Technique10.1155/2013/748273 ↗
6. Effect of hot rolling and heat treatment on anisotropy properties of LZ71 Mg alloy
7. A comprehensive study on the effect of heat treatment on the fracture behaviors and structural properties of Mg-Li alloys using RSM10.1088/2053-1591/ab1369 ↗
8. Comparison between laser beam and gas tungsten arc tailored welded blanks via deep drawing10.1177/0954405420962391 ↗
9. Microstructural and mechanical characterization of ARB AZ3110.4028/www.scientific.net/MSF.765.403 ↗
10. Strong and ductile AZ31 Mg alloy with a layered bimodal structure10.1038/s41598-019-41987-4 ↗
11. Production of Al/Mg-Li composite by the accumulative roll bonding process10.1016/j.jmrt.2020.05.084 ↗
12. Magnesium-lithium alloys in metal matrix composites — a preliminary report10.1007/BF01168957 ↗
13. Mechanical properties and microstructure of new magnesium—lithium base alloys10.1016/S0921-5093(96)10460-3 ↗
14. Microstructure and mechanical properties of the Mg/Al laminated composite fabricated by accumulative roll bonding (ARB)10.1016/j.msea.2010.02.001 ↗
15. Accumulative Roll Bonding—a review10.3390/app9173627 ↗
16. Role of shear strain in ultragrain refinement by accumulative roll-bonding (ARB) process10.1016/S1359-6462(01)01239-8 ↗
17. Microstructural characterization of Al/Mg alloy interdiffusion mechanism during Accumulative Roll Bonding10.1007/BF03027805 ↗
18. Microstructure and mechanical properties of Al/Cu/Mg laminated composite sheets produced by the ARB proces10.1007/s12613-018-1603-x ↗
19. Mechanical and microstructural properties of ultra-fine grained AZ91 magnesium alloy tubes processed via multi pass Tubular Channel Angular Pressing (TCAP)10.1016/j.jmst.2013.08.010 ↗
20. Microstructures and mechanical properties of ultrafine-grained Ti/AZ31 magnesium matrix composite prepared by powder metallurgy10.1016/j.apt.2018.09.001 ↗
21. A review on thermal conductivity of magnesium and its alloys10.1016/j.jma.2019.08.002 ↗
22. Microstructure and mechanical properties of wire and arc additive manufactured AZ31 magnesium alloy using cold metal transfer process10.1016/j.msea.2020.138942 ↗
23. Fracture toughness evaluation of ultrafine-grained nickel10.1016/j.scriptamat.2011.02.007 ↗
24. Effect of equal channel angular pressing on the fracture behavior of commercially pure titanium10.1007/s11661-009-0111-z ↗
25. Effect of equal channel angular pressing on fracture toughness of Al-707510.1016/j.engfailanal.2016.03.010 ↗
26. Analysis of standard fracture toughness test based on digital image correlation data10.1016/j.engfracmech.2017.05.045 ↗
27. Digital image correlation and fracture: an advanced technique for estimating stress intensity factors of 2D and 3D cracks10.1088/0022-3727/42/21/214004 ↗
28. Fracture toughness testing using photogrammetry and digital image correlation10.1016/j.mex.2018.09.012 ↗
29. Stress intensity factor measurements from digital image correlation: post-processing and integrated approaches10.1007/s10704-006-6631-2 ↗
30. Characterizing the elastic and plastic properties of the multilayered Al/Brass composite produced by ARB using DIC10.1016/j.msea.2019.03.002 ↗
31. ASTM, Standard Guide for Preparation of Metallographic Specimens, in: E3-11(2017), ASTM International, PA, 2017.
32. ASTM, Standard Test Methods for Tension Testing of Metallic Materials, in: E8 / E8M-16ae1, ASTM International, United States, 2016.
33. ASTM, Standard Test Method for Measurement of Fatigue Crack Growth Rates, in: ASTM E647–15e1, ASTM International, United States, 2015.
34. An analytical approach for necking and fracture of hard layer during accumulative roll bonding (ARB) of metallic multilayer10.1016/j.matdes.2015.10.088 ↗
35. Manufacturing of high-strength multilayered composite by accumulative roll bonding10.1088/2053-1591/ab6408 ↗
36. Grain refinement of magnesium alloy sheets by ARB using high-speed rolling mill
37. Influence of rolling temperature on microstructural evolution and mechanical behavior of AZ31 alloy with accumulative roll bonding10.1016/j.msea.2019.03.047 ↗
38. Texture development of ARB processed Mg/Al multilayers
39. Fracture toughness investigation of Al1050/Cu/MgAZ31ZB multi-layered composite produced by accumulative roll bonding process10.1016/j.msea.2018.08.017 ↗
40. Evaluation of fracture toughness and rupture energy absorption capacity of as-rolled LZ71 and LZ91 Mg alloy sheet10.1088/2053-1591/aaf54f ↗
41. Microstructure of Al–Mg dissimilar weld made by cold metal transfer MIG welding10.1179/174328408X278411 ↗
42. Weldability and Distortion of Mg AZ31-to-galvanized steel SPOT plug welding joint by Cold Metal Transfer Method10.1115/1.4034009 ↗