journal article·2023-05

Improving mechanical properties of laminate heterogeneous GW103K/AZ31 alloys

Lei Li, Lirong Xiao, Bo Gao, Yandong Yu, Zhonggang Sun, Yudong Sui, Wenwen Sun, Xuefei Chen, Hao Zhou

Publisher page

Abstract

The laminate heterogeneous GW103K (Mg-10Gd-3Y)/AZ31 (Mg-3Al-1Zn) alloys were obtained by diffusion bonding and hot rolling. The influence of the interfacial layer numbers on mechanical properties and microstructure evolution of laminate heterogeneous GW103K/AZ31 alloys were systematically studied. The 9-layer laminates exhibited an excellent combination of yield strength (210 MPa), ultimate tensile strength (269 MPa), and elongation (13.2%), which are much superior to the individual component materials. In addition, the 9-layer laminates also exhibited maximum extra strength and ductility that is higher than what is predicted by the rule of mixture. The strengthening and ductilization mechanisms of laminate heterogeneous GW103K/AZ31 alloys are discussed, which promotes the development of internal stress and can be correlated to the Bauschinger effect as measured by cyclic loading-unloading-reloading experiments. Detailed transmission electron microscopy observation was applied to characterize the interface structure of the laminate samples.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Magnesium Alloys: Properties and Applications · Aluminum Alloys Composites Properties · Advanced Welding Techniques Analysis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (52)

Show source-provided references
1. Bimodal grained Mg–0.5Gd–xMn alloys with high strength and low-cost fabricated by low-temperature extrusion10.1016/j.jallcom.2022.168008 ↗
2. Optimization of heat treatment condition of nonflammable Mg-Al-Ca alloys with high thermal conductivity10.1016/j.jallcom.2022.168014 ↗
3. Effect of pack-forging on microstructure and properties of Mg-Gd-Y-Zn-Zr alloy10.1016/j.msea.2020.140674 ↗
4. Solute redistribution and mechanism of structure refinement of Mg-Al alloy during solidification under high pressure10.1016/j.jallcom.2022.164777 ↗
5. Preparation of ultra-high strength Mg-Gd-Y-Zn-Zr alloy by pre-ageing treatment prior to extrusion
6. Tension-compression asymmetry and the underlying slip/twinning activity in extruded Mg - Y sheets10.1016/j.ijplas.2020.102878 ↗
7. High strength and high ductility of Mg-10Gd-3Y alloy achieved by a novel extrusion-shearing process10.1016/j.jallcom.2022.167498 ↗
8. In-situ TEM observations on interaction of basaldislocations and β′ phases in a Mg–Gd binary alloy10.1016/j.msea.2022.143017 ↗
9. On the exceptional creep resistance in a die-cast Gd-containing Mg alloy with Al addition10.1016/j.actamat.2022.117957 ↗
10. Effect of Nd on microstructure and mechanical properties of Mg-7Gd-0.5Zr alloy10.1016/j.jallcom.2022.168278 ↗
11. Gradient and lamellar heterostructures for superior mechanical properties10.1557/s43577-021-00056-w ↗
12. Heterostructured materials: superior properties from hetero-zone interaction10.1080/21663831.2020.1796836 ↗
13. Effects of heterogeneous ultrafine grain and strain rate on mechanical properties of CoCrNi medium entropy alloy10.1016/j.jallcom.2022.167791 ↗
14. Microstructure and mechanical properties of Ti basic bionic gradient heterogeneous alloy prepared by multi-wire arc additive manufacturing10.1016/j.jallcom.2022.166813 ↗
15. Heterogeneous lamella structure design to simultaneously strengthen and toughen aluminum alloys10.1016/j.jallcom.2022.167456 ↗
16. Simultaneously enhancing strength and ductility of a high-entropy alloy via gradient hierarchical microstructures10.1016/j.ijplas.2019.07.017 ↗
17. Mechanical properties and deformation mechanisms of gradient nanostructured metals and alloys10.1038/s41578-020-0212-2 ↗
18. High-strength and thermally stable bulk nanolayered composites due to twin-induced interfaces10.1038/ncomms2651 ↗
19. Ductilization of a diffusion-bonded heterostructured AZ31/GW103K/AZ31 alloy by interfacial reinforcement10.1016/j.msea.2022.143691 ↗
20. Development of microstructure and high hardness of Ti6Al4V alloy fabricated using laser beam powder bed fusion: a novel sub-transus heat treatment approach10.1016/j.jallcom.2022.168387 ↗
21. Strengthening and ductilization of laminate dual-phase steels with high martensite content10.1016/j.jmst.2020.03.083 ↗
22. Dual-phase hetero-structured strategy to improve ductility of a low carbon martensitic steel10.1016/j.msea.2021.142584 ↗
23. Manipulating the powder size to achieve enhanced strength and ductility in harmonic structured Al alloy10.1080/21663831.2019.1580621 ↗
24. Stiff, strong and ductile heterostructured aluminum composites reinforced with oriented nanoplatelets10.1016/j.scriptamat.2020.08.017 ↗
25. High strength-ductility of heterogeneous sandwich Mg-Y alloys produced by high pressure torsion10.1016/j.vacuum.2020.109568 ↗
26. Mechanical properties of copper/bronze laminates: role of interfaces10.1016/j.actamat.2016.06.023 ↗
27. Revealing hetero-deformation induced (HDI) stress strengthening effect in laminated Al-(TiB2+TiC)p/6063 composites prepared by accumulative roll bonding10.1016/j.jallcom.2019.152285 ↗
28. Soft/hard copper/bronze laminates with superior mechanical properties10.1016/j.msea.2019.04.069 ↗
29. Diffusion bonding of aluminum-magnesium using cold rolled copper interlayer10.1016/j.jallcom.2018.09.320 ↗
30. Transient liquid phase bonding of AZ31 magnesium alloy: metallurgical structure and mechanical properties10.1016/j.jmapro.2018.08.002 ↗
31. Contact-reaction brazing of an AZ31 magnesium/3003 aluminum alloy using a silver-copper-zinc interlayer10.1016/j.jmatprotec.2017.06.041 ↗
32. Microstructure and mechanical properties of extruded Mg–8.5Gd–2.3Y–1.8Ag–0.4Zr alloy10.1016/S1003-6326(11)61403-9 ↗
33. Perspective on hetero-deformation induced (HDI) hardening and back stress10.1080/21663831.2019.1616331 ↗
34. Back stress strengthening and strain hardening in gradient structure10.1080/21663831.2016.1153004 ↗
35. Atomic-scale three-dimensional structural characterisation of twin interface in Mg alloys10.1080/09500839.2020.1774935 ↗
36. Grain size effect on tensile properties and slip systems of pure magnesium10.1016/j.actamat.2020.116604 ↗
37. New polytypes of long-period stacking ordered structures in Mg–Co–Y alloys10.1016/j.scriptamat.2012.12.025 ↗
38. Effect of the interspacing of intragranular lamellar LPSO phase on dynamic recrystallization behaviors of Mg-Gd-Y-Zn-Zr alloys10.1016/j.matchar.2022.112326 ↗
39. Influence of volume fraction of long-period stacking ordered structure phase on the deformation processes during cyclic deformation of Mg-Y-Zn alloys10.3390/cryst11010011 ↗
40. A unified phenomenological description of work hardening and creep based on one-parameter models10.1016/0001-6160(84)90202-5 ↗
41. Twinning and the ductility of magnesium alloys10.1016/j.msea.2006.12.037 ↗
42. Enhanced deformation mechanisms by anisotropic plasticity in polycrystalline Mg alloys at room temperature10.1007/s11661-005-0032-4 ↗
43. On the relationship between and conjugate twins and double extension twins in rolled pure Mg10.1080/14786435.2017.1290846 ↗
44. The nanostructured origin of deformation twinning10.1021/nl203937t ↗
45. Orientation gradients and geometrically necessary dislocations in ultrafine grained dual-phase steels studied by 2D and 3D EBSD10.1016/j.msea.2010.01.004 ↗
46. Geometrically necessary dislocations and strain-gradient plasticity: a few critical issues10.1016/S1359-6462(02)00335-4 ↗
47. Indentation size effects in crystalline materials: a law for strain gradient plasticity10.1016/S0022-5096(97)00086-0 ↗
48. Evolution of dislocation density distributions in copper during tensile deformation10.1016/j.actamat.2013.08.027 ↗
49. In-situobservation of dislocation dynamics near heterostructured interfaces10.1080/21663831.2019.1616330 ↗
50. Philosophical magazine10.1080/14786437008238426 ↗
51. Interface affected zone for optimal strength and ductility in heterogeneous laminate10.1016/j.mattod.2018.03.006 ↗
52. Hetero-deformation induced (HDI) hardening does not increase linearly with strain gradient10.1016/j.scriptamat.2019.08.022 ↗