Effect of alumina content on microstructures, mechanical, wear and machining behavior of Cu-10Zn nanocomposite prepared by mechanical alloying and hot-pressing
Source abstract
Abstract
Abstract In the present research work, novel (Cu-10Zn)100-x – x wt.% Al2O3 (x = 0, 3, 6, 9 & 12) nanocomposites were manufactured by mechanical alloying process followed by vacuum hot-pressing technique. The mechanical properties (sinterability, hardness and compressive strength), wear behavior (coefficient of friction, wear rate and worn surface morphology) and machining behavior (surface roughness and chip thickness) were explained and investigated elaborately. The same compositions of (Cu-10Zn)100-x – x wt.% Al2O3 microcomposites (coarse crystalline matrix alloy reinforced with alumina) were also fabricated and compared with nanocomposites. It was observed that uniform distribution and embedding of nano-alumina in the nanocrystallite (nano-grain) matrix in nanocomposites were achieved which exhibited excellent performances. The (Cu-10Zn)88–12 wt% Al2O3 bulk nanocomposite produced highest compressive strength which was around 9.4 times higher than the same amount of reinforcement of microcomposites. Further, nanocomposites showed lower value of coefficient of friction and surface roughness which means a considerable wear resistance and good surface finish was obtained in nanocomposites.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloys Composites Properties · Advanced materials and composites · Microstructure and mechanical properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (32)
Show source-provided references
1. Fabrication and consolidation behavior of Al 6061 nanocomposite powders reinforced by multi-walled carbon nanotubes10.1016/j.powtec.2014.03.039 ↗
2. An investigation of the synthesis, consolidation and mechanical behaviour of Al 6061 nanocomposites reinforced by TiC via mechanical alloying10.1016/j.matdes.2013.12.067 ↗
3. Microstructure, cold workability and strain hardening behavior of trimodaled AA 6061–TiO2 nanocomposite prepared by mechanical alloying10.1016/j.msea.2011.05.056 ↗
4. An investigation on flowability and compressibility of AA 6061100−x-x wt.% TiO2 micro and nanocomposite powder prepared by blending and mechanical alloying10.1016/j.powtec.2010.03.013 ↗
5. Microstructures and tensile behavior of carbon nanotubes reinforced Cu matrix composites with molecularlevel dispersion10.1016/j.matdes.2011.08.021 ↗
6. Production and properties of Cu/Cr2O3 nano-composites10.1016/j.powtec.2012.02.001 ↗
7. In situ synthesis of TiB2 particulate reinforced copper matrix composite with a rotating magnetic field10.1016/j.matdes.2014.09.025 ↗
8. Copper and copper alloys
9. Tensile properties of 5052 Almatrix composites reinforced with B4C10.1007/s11661-001-0031-z ↗
10. Effect of the B4C content and the milling time on the synthesis, consolidation and mechanical properties of AlCuMg-B4C nanocomposites synthesized by mechanical milling10.1016/j.powtec.2016.04.004 ↗
11. Effect of process parameters on micro and macro-properties of an Al-based nanocomposite prepared by means of mechanical milling10.1016/j.jallcom.2013.02.084 ↗
12. Prediction of effect of reinforcement size and volume fraction on the abrasive wear behavior of AA2014/B4Cp MMCs using artificial neural network10.1007/s13369-014-1157-9 ↗
13. Prediction of the influence of processing parameters on synthesis of Al2024-B4C composite powders in a planetary mill using an artificial neural network10.1515/secm-2013-0148 ↗
14. Effect of volume fraction and size of B4C particles on production and microstructure properties of B4C reinforced aluminum alloy composites10.1179/1743284713Y.0000000232 ↗
15. Nanocrystalline materials and coatings10.1016/j.mser.2004.07.001 ↗
16. Breakthroughs in optimization of mechanical properties of nanostructured metals and alloys10.1002/adem.200500094 ↗
17. Nanocrystalline materials10.1016/0079-6425(89)90001-7 ↗
18. Synthesis and characterization of high-energy ball milled nanostructured Fe50Ni5010.1016/j.cattod.2005.11.084 ↗
19. Spinodal decomposition and precipitation in Cu–Cr nanocomposite10.1016/j.jallcom.2013.11.019 ↗
20. Microstructure and properties of AA7075/Al–SiC composites fabricated using powder metallurgy and hot pressing10.1016/j.powtec.2014.08.016 ↗
21. Fabrication of nano-grained Ti–Nb–Zr biomaterials using spark plasma sintering10.1016/j.matdes.2015.08.082 ↗
22. Wear behavior of nanostructured Al and Al–B4C nanocomposites produced by mechanical milling and hot extrusion10.1007/s11249-011-9825-3 ↗
23. Dry sliding wear behaviour of AA 6351-ZrB2 in situ composite at room temperature10.1016/j.matdes.2009.09.017 ↗
24. Sliding wear behaviour of Al 6063/TiB2 in situ composites at elevated temperatures10.1016/j.matdes.2008.09.037 ↗
25. Effect of nose radius and graphite addition on turning of AA 7075-ZrB2 in-situ composites10.1016/j.proeng.2014.12.286 ↗
26. Experimental investigation on mechanical and turning behavior of Al 7075- x% wt. TiB2 – 1%Gr in-situ hybrid composite
27. Lőffler · Nanostruct. Mater. · 1995 · 6 · 56710.1016/0965-9773(95)00122-0 ↗
28. Synthesis and characterization ofW80Ni10Mo10 alloy produced by mechanical alloying
29. Synthesis and structural characterization of Cu-Zn- x wt.%Al2O3 (x = 0,3,6,9&12%) nanocomposites powders through mechanical alloying10.1016/j.jallcom.2016.07.026 ↗
30. SiC content effect on the properties of Cu–SiC composites produced by mechanical alloying10.1016/j.jallcom.2015.01.298 ↗
31. Achieving highly dispersed nanofibres at high loading in carbon nanofibre–metal composites10.1088/0957-4484/20/23/235607 ↗
32. Extraordinary strengthening effect of carbon nanotubes in metal-matrix nanocomposites processed by molecular-level mixing10.1002/adma.200401933 ↗