journal article·2019-05

Coupling effects of rare-earth Pr and Al2O3 nanoparticles on the microstructure and properties of Sn-0.3Ag-0.7Cu low-Ag solder

Jie Wu, Songbai Xue, Jingwen Wang, Mingfang Wu

Publisher page

Abstract

Abstract Low-cost Al2O3 nanoparticles (NPs) are regularly incorporated into lead-free solder to improve its mechanical performance, but the poor wettability of Al2O3 NPs leads to weak Al2O3/solder interface bonding. In this work, a novel idea different from the common solution of pre-coating a metal layer on the surface of NPs was proposed to address the issue of weak interface bonding by simultaneously doping rare-earth (RE) Pr (0.06 wt%) and Al2O3 NPs (0–0.5 wt%) into Sn-0.3Ag-0.7Cu low-Ag solder. The coupling effects of RE Pr and Al2O3 NPs on the wettability, microstructures, shear force and creep resistance of prepared nanocomposite solder were systematically investigated. It was found that the coupling effects were concentration dependent. When the content of Al2O3 NPs was less than 0.06 wt%, a synergistic relationship between free Pr atoms and Al2O3 NPs was established. This is because the surface-active Pr atoms, acting as bridges between Al2O3 NPs and solder matrix, can be spontaneously adsorbed at the surfaces of Al2O3 NPs to in situ form Pr-coated Al2O3 NPs, which have much better wettability than the single Al2O3 NPs. However, increasing the doping content of Al2O3 NPs over 0.06 wt% led to a competitive relationship among free Pr atoms, Al2O3 NPs and Pr-coated Al2O3 NPs, which was probably caused by the emerged Al2O3 agglomerates occupying partial space of grain surfaces. The optimum doping content of Al2O3 NPs in SAC0307–0.06Pr solder was approximately 0.06 wt% and SAC0307–0.06Pr-0.06Al2O3 possessed the best wettability, a well-controlled growth of interfacial IMC layer, the highest shear force (∼61 N) and a superior room-temperature creep resistance with creep stress exponent (n) reaching approximately 11.7.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Electronic Packaging and Soldering Technologies · Intermetallics and Advanced Alloy Properties · Aluminum Alloys Composites Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (39)

Show source-provided references
1. Are you ready for lead-free electronics10.1109/TCAPT.2005.859353 ↗
2. Properties of lead-free solder alloys with rare earth element additions10.1016/j.mser.2004.01.001 ↗
3. A review of lead-free solders for electronics applications10.1016/j.microrel.2017.06.016 ↗
4. Effects of Ag content on fracture resistance of Sn-Ag-Cu lead-free solders under high-strain rate conditions10.1016/j.msea.2007.01.145 ↗
5. Drop failure modes of Sn-3.0Ag-0.5Cu solder joints in wafer level chip scale package10.1016/S1003-6326(16)64272-3 ↗
6. Structure and properties of lead-free solders bearing micro and nano particles
7. Effects of Ag addition on solid-state interfacial reactions between Sn-Ag-Cu solder and Cu substrate10.1016/j.matchar.2017.01.004 ↗
8. Effect of Pr addition on properties and Sn whisker growth of Sn-0.3 Ag-0.7 Cu low-Ag solder for electronic packaging10.1007/s10854-017-6790-0 ↗
9. Study on microstructure and properties of Sn-0.3Ag-0.7Cu solder bearing Nd10.1007/s10854-016-4901-y ↗
10. Effect of La2O3 on microstructure and properties of Sn-58Bi solder during repeated remelting process
11. Effects of Ga addition on microstructure and properties of Sn-Ag-Cu/Cu solder joints10.1016/j.jallcom.2014.11.030 ↗
12. Effects of trace amount praseodymium and neodymium on microstructure and mechanical properties of Sn-0.3Ag-0.7Cu-0.5 Ga solder10.1007/s10854-015-3761-1 ↗
13. Reinforcement of graphene nanosheets on the microstructure and properties of Sn58Bi lead-free solder10.1016/j.matdes.2016.10.034 ↗
14. Reliability enhancement of Sn-1.0Ag-0.5Cu nano-composite solders by adding multiple sizes of TiO2 nanoparticles10.1016/j.jallcom.2016.12.037 ↗
15. Effects of nano-Al2O3 additions on microstructure development and hardness of Sn3.5Ag0.5Cu solder10.1016/j.matdes.2010.04.033 ↗
16. Interfacial intermetallic growth and mechanical properties of carbon nanotubes reinforced Sn3. 5Ag0.5Cu solder joint under current stressing10.1016/j.jallcom.2014.01.083 ↗
17. The influence of addition of Al nano-particles on the microstructure and shear strength of eutectic Sn-Ag-Cu solder on Au/Ni metallized Cu pads10.1016/j.jallcom.2010.06.180 ↗
18. The influence of a small amount of Al and Ni nano-particles on the microstructure, kinetics and hardness of Sn-Ag-Cu solder on OSP-Cu pads10.1016/j.intermet.2012.04.019 ↗
19. Effects of TiO2, nanoparticles addition on microstructure, microhardness and tensile properties of Sn-3.0Ag-0.5Cu-xTiO2 composite solder10.1016/j.matdes.2013.10.033 ↗
20. Growth mechanism of intermetallic compounds and damping properties of Sn-Ag-Cu-1wt% nano-ZrO2, composite solders10.1016/j.microrel.2014.01.026 ↗
21. Microstructures and properties of new Sn-Ag-Cu lead-free solder reinforced with Ni-coated graphene nanosheets10.1016/j.jallcom.2015.09.178 ↗
22. Influence of Ag-modified graphene nanosheets addition into Sn-Ag-Cu solders on the formation and growth of intermetallic compound layers10.1016/j.jallcom.2017.01.286 ↗
23. Sn-3.0Ag-0.5Cu nanocomposite solders reinforced by graphene nanosheets10.1007/s10854-016-4631-1 ↗
24. Interfacial reaction and shear strength of Ni-coated carbon nanotubes reinforced Sn-Ag-Cu solder joints during thermal cycling10.1016/j.intermet.2012.06.002 ↗
25. Morphology characterization of multi-walled carbon nanotubes in Sn-58Bi/CNTs composites10.2320/matertrans.M2013117 ↗
26. Influence of dual ceramic nanomaterials on the solderability and interfacial reactions between lead-free Sn-Ag-Cu and a Cu conductor
27. Effect of nano Al2O3 additions on the interfacial behavior and mechanical properties of eutectic Sn-9Zn solder on low temperature wetting and soldering of 6061 aluminum alloys10.1016/j.jallcom.2016.11.136 ↗
28. 2003
29. 2003
30. Influence of Zn addition on the microstructure, melt properties and creep behavior of low Ag-content Sn-Ag-Cu lead-free solders10.1016/j.msea.2014.04.070 ↗
31. Melting and solidification properties of the nanoparticles of Sn3.0Ag0.5Cu lead-free solder alloy10.1016/j.matchar.2010.02.004 ↗
32. Effect of γ-Fe2O3 nanoparticles size on the properties of Sn-1.0Ag-0.5Cu nano-composite solders and joints10.1016/j.jallcom.2015.11.213 ↗
33. Effect of nano-Fe2O3, additions on wettability and interfacial intermetallic growth of low-Ag content Sn-Ag-Cu solders on Cu substrates10.1016/j.jallcom.2014.12.024 ↗
34. DeKock · 1989 · 91
35. Kinetic analysis of the soldering reaction between eutectic SnPb alloy and Cu accompanied by ripening10.1103/PhysRevB.53.16027 ↗
36. Creep mitigation in Sn-Ag-Cu composite solder with Ni-coated carbon nanotubes10.1007/s10854-011-0557-9 ↗
37. Structural characterization and creep resistance of nano-silicon carbide reinforced Sn-1.0Ag-0.5Cu lead-free solder alloy10.1016/j.matdes.2013.10.043 ↗
38. Improved strength of Ni and Zn doped Sn-2.0A-0.5Cu lead-free solder alloys under controlled processing parameters10.1016/j.matdes.2012.12.081 ↗
39. Dislocation climb-dislocations-chapter V10.1016/B978-0-08-013523-6.50010-7 ↗