journal article·2019-06

Variation of microstructure and mechanical properties of hybrid particulates reinforced Al-alloy matrix composites with ultrasonic treatment

Jianyu Li, Fei Li, Shusen Wu, Shulin Lü, Wei Guo, Xiong Yang

Publisher page

Abstract

Abstract The effects of ultrasonic treatment (UT) on the microstructure and mechanical properties of 10 wt% Mg2Si+1 wt% nano-sized SiC particles (SiCnp for short) hybrid reinforced Al-Cu alloy matrix composites were investigated for first time. The existence of Mg2Si phase solves the problem effectively that the particle content of SiCnp/Al-Cu composites cannot be high by the external addition of SiCnp and casting method. The results show that after UT, the big eutectic Mg2Si phase was remarkably refined, from coarse Chinese characters (about 50 μm) to fine strips or dots (about 0.5–2 μm). Meanwhile SiCnp agglomerations were also eliminated, and both Mg2Si phase and SiCnp were uniformly distributed in the composites. The interaction between Mg2Si and SiCnp was discussed to analyze this behavior that SiCnp could act as heterogeneous nucleus of Mg2Si phase, or be captured by the Mg2Si solid front during solidification, leading to the refinement of eutectic Mg2Si phase. It was also found that the effects of UT could be even improved by using squeeze casting (SC), instead of gravity casting (GC). The as-cast ultimate tensile strength (UTS) and elongation of hybrid Mg2Si + SiCnp/Al-Cu composites fabricated by combining UT and SC were enhanced to 336 MPa and 3.0%, which were increased by 31.3% and 130.8%, respectively, compared with the composites without UT. The UTS of the hybrid Mg2Si + SiCnp/Al-Cu composites was also 33.5% higher than that of the Al-Cu matrix alloy and 23.5% higher than that of 1 wt% SiCnp/Al-Cu composites prepared by the same process.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloys Composites Properties · Aluminum Alloy Microstructure Properties · Advanced Welding Techniques Analysis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (41)

Show source-provided references
1. Study on the preparation of the SiCp/Al-20Si-3Cu functionally graded material using spray deposition10.1016/j.msea.2010.06.090 ↗
2. Comparison of microstructure and mechanical properties of A356 aluminum alloy/Al2O3 composites fabricated by stir and compo-casting processes10.1016/j.matdes.2011.07.037 ↗
3. High strength and good ductility of casting Al-Cu alloy modified by PrxOy and LaxOy10.1016/j.jallcom.2010.09.059 ↗
4. Microstructures and tensile properties of Al–Cu matrix composites reinforced with nano-sized SiCp fabricated by semisolid stirring process10.3390/met7020049 ↗
5. Microstructural evolution of the in situ Al-15wt.%Mg2Si composite with extra Si contents10.1016/S1359-6462(00)00338-9 ↗
6. In-situ fabrication technique of Al-matrix composites reinforced with single or hybrid particles
7. Preparation of in-situ TiB2 and Mg2Si hybrid particulates reinforced Al-matrix composites10.1016/j.jallcom.2015.08.162 ↗
8. Microstructural evolution and high temperature mechanical properties of cast Al-15Mg2Si-xGd in situ composites10.1016/j.jallcom.2017.01.015 ↗
9. Effect of La inoculation on composition, content, granularity and mechanical properties of in-situ Al-30wt%Mg2Si composite10.1016/j.msea.2017.08.010 ↗
10. The influence of Cu rich intermetallic phases on the microstructure, hardness and tensile properties of Al–15% Mg2Si composite10.1016/j.msea.2010.01.063 ↗
11. Effect of Mn addition on the microstructure and tensile properties of Al–15%Mg2Si composite10.1016/j.msea.2012.04.056 ↗
12. Heterogeneous nucleating role of TiB2 or AlP/TiB2 coupled compounds on primary Mg2Si in Al–Mg–Si alloys10.1016/j.msea.2008.07.034 ↗
13. Refinement and modification performance of Al–P master alloy on primary Mg2Si in Al–Mg–Si alloys10.1016/j.jallcom.2007.10.111 ↗
14. Effect of extrusion and particle volume fraction on the mechanical properties of SiC reinforced Al-Cu alloy composites10.1016/j.msea.2010.07.017 ↗
15. Investigation of tribological and mechanical properties Al2O3-SiC reinforced Al composites manufactured by casting or P/M method10.1016/j.matdes.2008.04.014 ↗
16. Effects of ultrasonic vibration on microstructure and mechanical properties of nano-sized SiC particles reinforced Al-5Cu composites10.1016/j.ultsonch.2017.12.038 ↗
17. Microstructures and tensile properties of nano-sized SiCp/Al-Cu composites fabricated by semisolid stirring assisted with hot extrusion10.1016/j.matchar.2017.07.013 ↗
18. Wetting and oxidation during ultrasonic soldering of an alumina reinforced aluminum-copper-magnesium (2024 Al) matrix composite10.1016/j.compositesa.2011.12.006 ↗
19. Effects of ultrasonic vibration and manganese on microstructure and mechanical properties of hypereutectic Al-Si alloys with 2%Fe10.1016/j.intermet.2012.09.001 ↗
20. Refinement of LPSO structure in Mg-Ni-Y alloys by ultrasonic treatment10.1016/j.ultsonch.2017.07.042 ↗
21. Improvement of particles distribution of in-situ 5 vol% TiB2 particulates reinforced Al-4.5Cu alloy matrix composites with ultrasonic vibration treatment10.1016/j.jallcom.2016.09.013 ↗
22. Grain refinement of AZ91 alloy by introducing ultrasonic vibration during solidification10.1016/j.matlet.2008.01.063 ↗
23. Effects and mechanism of ultrasonic irradiation on solidification microstructure and mechanical properties of binary TiAl alloys10.1016/j.ultsonch.2017.03.006 ↗
24. Theoretical estimation of the temperature and pressure within collapsing acoustical bubbles10.1016/j.ultsonch.2013.05.008 ↗
25. Squeeze casting: an overview10.1016/S0924-0136(99)00291-5 ↗
26. Nucleation effect of alumina in Al-Si/Al2O3 composites10.1023/A:1006643609938 ↗
27. Zone-melted unidirectional solidification of particulate dispersed composites10.1023/A:1004874027612 ↗
28. Nucleation catalysis10.1021/ie50510a031 ↗
29. High-energy ultrasonic field effects on the microstructure and mechanical behaviors of A356 alloy10.1016/j.jallcom.2008.02.091 ↗
31. Influence of ultrasonic vibration on mechanical properties and microstructure of 1Cr18Ni9Ti stainless steel10.1016/j.matdes.2006.04.025 ↗
32. Microstructure evolution and mechanical properties of quasicrystal-reinforced Mg-Zn-Y alloy subjected to ultrasonic vibration10.1016/j.msea.2016.10.035 ↗
33. Effects of vibration during solidification10.1179/imr.1981.26.1.71 ↗
34. Research on solidification of metal melt under Ultrasonic field
35. Development of non-dendritic microstructure of aluminum alloy in semi-solid state under ultrasonic vibration10.4028/www.scientific.net/SSP.141-143.451 ↗
36. Effect of particle distribution on deformation and damage of two-phase alloys10.1016/S0921-5093(01)01168-6 ↗
37. Effect of clustering on the mechanical properties of SiC particulate-reinforced aluminum alloy 2024 metal matrix composites10.1016/S0921-5093(02)00593-2 ↗
38. Al-4wt% Cu composite reinforced with in-situ TiB2 particles10.1016/S1359-6454(97)00075-X ↗
39. Enhanced tensile ductility and toughness in nanostructured Cu10.1063/1.1465528 ↗
40. Consideration of Orowan strengthening effect in particulate-reinforced metal matrix nanocomposites: a model for predicting their yield strength10.1016/j.scriptamat.2005.12.017 ↗
41. Effects of SiC nanoparticle content on the microstructure and tensile mechanical properties of ultrafine grained AA6063-SiCnp composites fabricated by powder metallurgy10.1016/j.jmst.2016.09.022 ↗