Mechanical properties and strain hardening behavior of aluminum matrix composites reinforced with few-walled carbon nanotubes
Source abstract
Abstract
Abstract In this study, for the first time few-walled carbon nanotubes (FWCNTs) with ∼3 walls were used as reinforcements in fabricating high performance aluminum matrix composites (AMCs). FWCNTs/Al composites and referential Al materials were prepared by a powder metallurgy route consisting of high energy ball milling, spark plasma sintering (SPS) and subsequent hot extrusion. It is found that, by decreasing SPS temperature and time, FWCNTs/Al composites showed reduced grains with an increased dislocation density and improved structural integrity of FWCNTs, leading to an increased tensile strength. Meanwhile, comparatively high strain hardening rates and long strain softening behavior were observed after necking in the sample sintered at 500 °C, which resulted in a tensile elongation of 11.7% with a high yield strength of 382 MPa. The experimental results suggested that, compared with traditional multi-walled carbon nano-tubes (MWCNTs), FWCNTs showed a noticeably enhanced strengthening effect and provided a good balance of strength and ductility in Al composites. It may make FWCNTs a good reinforcement candidate for metal matrix composites to achieve improved mechanical properties.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloys Composites Properties · Advanced ceramic materials synthesis · MXene and MAX Phase Materials
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (33)
Show source-provided references
1. Novel nanoparticle-reinforced metal matrix composites with enhanced mechanical properties10.1002/adem.200700106 ↗
2. Nishida · 2013
3. Carbon nanotubes: properties and application10.1016/j.mser.2003.10.001 ↗
4. Recent progress in the development and properties of novel metal matrix nanocomposites reinforced with carbon nanotubes and graphene nanosheets10.1016/j.mser.2013.08.001 ↗
5. Carbon nanotube reinforced metal matrix composites - a review10.1179/095066009X12572530170543 ↗
6. Load transfer strengthening in carbon nanotubes reinforced metal matrix composites via in-situ tensile tests10.1016/j.compscitech.2015.03.009 ↗
7. Tensile properties of fibre-reinforced metals: copper/tungsten and copper/molybdenum10.1016/0022-5096(65)90035-9 ↗
8. Growth, structure, and properties of graphite whiskers10.1063/1.1735559 ↗
9. Mechanics of deformation of single- and multi-wall carbon nanotubes10.1016/j.jmps.2003.08.004 ↗
10. Influence of the concentration and nature of carbon nanotubes on the mechanical properties of AA5083 aluminium alloy matrix composites10.1016/j.carbon.2014.05.001 ↗
11. Fabrication and properties of dispersed carbon nanotube–aluminum composites10.1016/j.msea.2009.01.002 ↗
12. An approach to obtaining homogeneously dispersed carbon nanotubes in Al powders for preparing reinforced Al-matrix composites10.1002/adma.200601381 ↗
13. An approach to the uniform dispersion of a high volume fraction of carbon nanotubes in aluminum powder10.1016/j.carbon.2011.01.021 ↗
14. Microstructural evaluation and mechanical properties of Al-CNT nanocomposites produced by different processing methods10.1016/j.jallcom.2017.06.222 ↗
15. The influence of carbon nanotube (CNT) morphology and diameter on the processing and properties of CNT-reinforced aluminium composites10.1016/j.compositesa.2010.11.008 ↗
16. Multiwall nanotubes can be stronger than single wall nanotubes and implications for nanocomposite design10.1103/PhysRevLett.103.045502 ↗
17. An approach for homogeneous carbon nanotube dispersion in Al matrix composites10.1016/j.matdes.2015.02.003 ↗
18. Extraordinary reinforcing effect of carbon nanotubes in aluminium matrix composites assisted by in-situ alumina nanoparticles10.1016/j.compositesb.2019.107691 ↗
19. Dispersion of carbon nanotubes (CNTs) in aluminum powder10.1016/j.compositesa.2006.04.006 ↗
20. Effect of initial state on dispersion evolution of carbon nanotubes in aluminium matrix composites during a high-energy ball milling process10.1080/00325899.2016.1144375 ↗
21. Microstructure of heteroepitaxial GaN revealed by x-ray diffraction10.1063/1.1571217 ↗
22. Carbon nanotube induced microstructural characteristics in powder metallurgy Al matrix composites and their effects on mechanical and conductive properties10.1016/j.jallcom.2015.08.178 ↗
23. Solid-state interfacial reaction and load transfer efficiency in carbon nanotubes (CNTs)-reinforced aluminum matrix composites10.1016/j.carbon.2016.12.013 ↗
24. Effect of ball-milling time on mechanical properties of carbon nanotubes reinforced aluminum matrix composites10.1016/j.compositesa.2012.07.026 ↗
25. In situ synthesized Al4C3Nanorods with excellent strengthening effect in aluminum matrix composites10.1002/adem.201400232 ↗
26. Length effect of carbon nanotubes on the strengthening mechanisms in metal matrix composites10.1016/j.actamat.2017.08.048 ↗
27. Hall–Petch relation and boundary strengthening10.1016/j.scriptamat.2004.06.002 ↗
28. Meyers · 2009
29. Strengthening in carbon nanotube/aluminium (CNT/Al) composites10.1016/j.scriptamat.2005.07.022 ↗
30. Frost · 1982
31. An analysis of the factors affecting strengthening in carbon nanotube reinforced aluminum composites10.1016/j.carbon.2010.09.054 ↗
32. Recent progress on the dispersion and the strengthening effect of carbon nanotubes and graphene-reinforced metal nanocomposites: a review
33. CNT-reinforced metal and steel nanocomposites: a comprehensive assessment of progress and future directions10.1016/j.compositesa.2018.08.010 ↗