journal article·2019-10

Vacuum brazing of the ultrathin-walled structure using particulate-reinforced composite filler metal: Microstructural evolution and mechanical properties

W.P. Han, M. Wan, R. Zhao, H. Kang

Publisher page

Abstract

Abstract A novel Inconel 718 particulate reinforced composite filler metal was used to fabricate the Ni-based superalloy ultrathin-walled structure by vacuum brazing. The brazing process was carried out at various temperatures (1423 K, 1443 K, 1463 K). Moreover, the effects of brazing temperature and the particulate content on wettability, solidification behaviour, typical microstructural evolution and the mechanical properties of the brazed ultrathin-walled structure were investigated in detail. The results indicate that increasing reinforced particulate would result in a worse wettability and higher liquidus temperature of the composite filler metal, which is attributed to the inevitable diffusion phenomenon. The microstructure in the brazed region is mainly composed of γ-Ni solid solution, Ni 5 Si 2 , Cr 3 Ni 5 Si 2 , G-phase and Ni–Si–Nb intermetallic compound. The elevated brazing temperature would cause a significant decrease in the mechanical properties of the ultrathin-walled structure. With the addition of the reinforced particulate, the mechanical properties increase obviously and the response effect of the particulate is better at higher brazing temperature. Meanwhile, the area of the Ni-based solid solution and the dispersion degree of the eutectic phase in the brazing fillet increase as the increase of the particulate content. However, the solute loss phenomenon induced by adding excessive reinforced particulate would decrease the mechanical properties. The result reveals that the tensile strength increases by 70 MPa, 103 MPa and 100 MPa, while the elongation increases by 0.8%, 5.4% and 6.8% at various brazing temperatures, comparing with the ultrathin-walled structure using the initial filler metal.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloys Composites Properties · Intermetallics and Advanced Alloy Properties · Aluminum Alloy Microstructure Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (58)

Show source-provided references
1. Development of a hypersonic aircraft design optimization tool10.4028/www.scientific.net/AMM.553.847 ↗
2. Wang · 2014 · vol. 39 · 31
3. Development study of a precooler for the air-turboramjet expander-cycle engine10.2514/2.5869 ↗
4. Countermeasures against the icing problem on the ATREX precooler10.1016/S0094-5765(03)00239-X ↗
5. Development study of precooled-cycle hypersonic turbojet engine for flight demonstration10.1016/j.actaastro.2007.01.012 ↗
6. Experimental studies on frost and defrost of fine tube bundles under coolant temperature between −20 and −58°C10.1016/j.ijheatmasstransfer.2017.09.031 ↗
7. Heat exchanger development at reaction engines Ltd10.1016/j.actaastro.2009.11.010 ↗
8. Overview of the key technologies of combined cycle engine precooling systems and the advanced applications of micro-channel heat transfer10.1016/j.ast.2014.08.008 ↗
9. The microstructure and mechanical properties of deposited-IN718 by selective laser melting10.1016/j.jallcom.2011.10.107 ↗
10. Microstructural characterization, formation mechanism and fracture behavior of the needle δ phase in Fe–Ni–Cr type superalloys with high Nb content10.1016/j.matchar.2015.09.011 ↗
11. Hot workability and microstructure evolution of the nickel-based superalloy Inconel 718 produced by laser metal deposition10.1016/j.jallcom.2018.01.029 ↗
12. Effect of hot deformation on γ″ and δ phase precipitation of Inconel 718 alloy during deformation&isothermal treatment10.1016/j.jallcom.2017.05.042 ↗
13. Density determination and simulation of Inconel 718 alloy at normal and metastable liquid states10.1016/j.jmst.2017.10.014 ↗
14. Precipitation behavior during high-temperature isothermal compressive deformation of Inconel 718 alloy10.1016/j.msea.2016.09.088 ↗
15. Comparative study on laser brazing and furnace brazing of Inconel 718 alloys with silver based filler metal10.1016/j.optlastec.2014.11.026 ↗
16. Solidification and solid state phenomena during TLP bonding of IN718 superalloy using Ni–Si–B ternary filler alloy10.1016/j.jallcom.2013.02.100 ↗
17. Phase transformations during diffusion brazing of IN718/Ni–Cr–B/IN71810.1179/1743284713Y.0000000238 ↗
18. Microstructure evolution mechanism during post-bond heat treatment of transient liquid phase bonded wrought IN718 superalloy: an approach to fabricate boride-free joints10.1016/j.jallcom.2017.06.206 ↗
19. Effects of post-weld heat treatment on microstructure and mechanical properties of TLP bonded Inconel718 superalloy10.1016/j.msea.2013.10.013 ↗
20. Effect of gap size and process parameters on diffusion brazing of Inconel 73810.1179/136217104225012175 ↗
21. TLP bonding of cast IN718 nickel based superalloy: process–microstructure–strength characteristics10.1016/j.msea.2013.01.029 ↗
22. Transient liquid phase bonding of Inconel 718 and Inconel 625 with BNi-2: modeling and experimental investigations10.1016/j.msea.2006.10.045 ↗
23. Microstructure development during transient liquid phase bonding of GTD-111 nickel-based superalloy10.1016/j.jallcom.2007.07.108 ↗
24. A study of the effect of filler metal thickness on tensile strength for a stainless steel plate-fin structure by experiment and finite element method10.1016/j.matdes.2009.11.062 ↗
25. Effect of holding time on vacuum brazing for a stainless steel plate-fin structure10.1016/j.matdes.2009.11.001 ↗
26. Structural performance of Inconel 625 superalloy brazed joints10.1007/s11665-016-2491-8 ↗
27. Vacuum brazing of Ti 2 AlNb and TC4 alloys using Ti–Zr–Cu–Ni and Ti–Zr–Cu–Ni + Mo filler metals: microstructural evolution and mechanical properties10.1016/j.acme.2017.10.006 ↗
28. Microstructure evolution of Si3N4/Si3N4 joint brazed with Ag-Cu-Ti plus SiCp composite filler10.1016/j.ceramint.2010.02.010 ↗
29. Wide gap brazing of stainless steel to nickel-based superalloy10.1016/S0924-0136(01)00596-9 ↗
30. Influence of solid-state diffusion during equilibration on microstructure and fatigue Life of superalloy wide-gap brazements10.1007/s11661-013-1849-x ↗
31. Effect of post-bond heat treatment on microstructural evolution and mechanical properties of brazed ultrathin-walled structure10.1016/j.msea.2018.11.057 ↗
32. Strength and microstructure of silicon nitride ceramics Brazed with Nickel-Chromium-Silicon Alloys
33. Infrared repair brazing of 403 stainless steel with a nickel-based braze alloy10.1007/s11661-002-0185-3 ↗
34. Experimental investigation and thermodynamic modeling of the Cr-Ni-Si system10.1007/s11661-006-0248-y ↗
35. Melting behaviour of nickel—chromium—silicon alloys10.1016/0040-6031(79)87098-7 ↗
36. Experimental investigation of phase equilibria in the Ni-Cr-Si ternary system10.1007/s11669-014-0279-9 ↗
37. The brazing of Si3N4 with Ni-Cr-Si alloys10.1016/0955-2219(95)00015-M ↗
38. Wide gap braze repair of gas turbine blades and vanes—a review10.1115/1.4003962 ↗
39. The Cr-Ni-Si (Chromium-Nickel-Silicon) system
40. Phase-field modeling of microstructure formation during rapid solidification in Inconel 718 superalloy10.1016/j.actamat.2015.05.052 ↗
41. Xiao · 2015
42. The Cr-Ni-Si (chromium-nickel-silicon) system10.1007/BF02736465 ↗
43. Structure of Vacuum Brazed BNi-5 Joint of Inconel 718
44. Binary alloy phase diagrams
45. Massalski · 1990
46. Transient liquid phase bonding of IC10 single crystal with GH3039 superalloy using BNi2 interlayer: microstructure and mechanical properties10.1016/j.matdes.2015.11.041 ↗
47. Modelling of transient liquid phase bonding
48. Formation of eutectic-type microconstituent during transient liquid phase bonding of nickel: influence of process parameters10.1179/174328407X185929 ↗
49. A dissolution model of base metal in liquid brazing filler metal during high temperature brazing10.1016/j.scriptamat.2003.12.032 ↗
50. Influence of bonding variables on transient liquid phase bonding behavior of nickel based superalloy IN-738LC10.1016/j.matdes.2013.05.042 ↗
51. Cottrell · 1958
52. Structural performance of Inconel 625 superalloy brazed joints10.1007/s11665-016-2491-8 ↗
53. Effect of holding time on microstructure and mechanical properties of SiC/SiC joints brazed by Ag-Cu-Ti + B 4 C composite filler10.1016/j.matchar.2016.06.008 ↗
54. Zirconia ceramic and Nb joints brazed with Mo-particle-reinforced Ag-Cu-Ti composite fillers: interfacial microstructure and formation mechanism10.1016/j.ceramint.2017.04.133 ↗
55. Brazing ZrO2 ceramic and TC4 alloy by novel WB reinforced Ag-Cu composite filler: microstructure and properties10.1016/j.ceramint.2017.08.069 ↗
56. Microstructural development in transient liquid-phase bonding
57. Nash · 1991
58. Joining of SiC nanowires-toughened SiC coated C/C composites and nickel based superalloy (GH3044) using Ni71CrSi interlayer10.1016/j.jallcom.2016.09.245 ↗