journal article·2026-05Open access

Effect of melt spinning on microstructure and corrosion uniformity of Zn-Ag-based alloy

Bashir Ahamed, Hamid Reza Bakhsheshi-Rad, Md Tanvir Hossain, Erico Freitas, Joseph Tomei, Jaroslaw W. Drelich

Abstract

Zinc (Zn) alloys are widely studied as biodegradable materials for interventional medical applications. However, Zn alloys produced by traditional casting and extrusion methods exhibit uneven corrosion resistance due to the presence of large intermetallic particles and a coarse microstructure. In this study, we demonstrate that melt spinning significantly refines the microstructure and intermetallics, thereby enhancing the alloy's corrosion uniformity. The grain size distribution is reduced from 3-11 μm to 0.8-1.2 μm, with an increase in the proportion of recrystallized regions and a decrease in crystal preferential orientation. Additionally, we report a simultaneous decrease in both the volume fraction and the number density of ε -AgZn3 nanoparticle precipitates after melt spinning. Mechanical testing reveals a yield strength of 396-408 MPa, an ultimate tensile strength of 410-420 MPa, and an elongation of approximately 16% for the melt-spun alloy. Additionally, this alloy demonstrates polarization resistance of 0.38 kΩ cm2 in its melt-spun condition, and very uniform corrosion progression. This favorable corrosion performance is attributed to the formation of a dense, stable passive layer that provides effective protection. This layer forms through the interaction of oxide and corrosion products in Hank's solution.
Source: europepmc · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Electronic Packaging and Soldering Technologies · Nanomaterials and Printing Technologies · Microstructure and mechanical properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (70)

Show source-provided references
1. Biodegradable metals for cardiovascular stents: from clinical concerns to recent Zn-Alloys10.1002/adhm.201501019 ↗
2. Zinc-based alloys for degradable vascular stent applications10.1016/j.actbio.2018.03.005 ↗
3. Recent research and progress of biodegradable zinc alloys and composites for biomedical applications: biomechanical and biocorrosion perspectives
4. A comprehensive review of the current research status of biodegradable zinc alloys and composites for biomedical applications10.3390/ma16134797 ↗
5. Bioresorbable vascular metallic scaffolds: current status and research trends
6. A novel high-strength Zn-3Ag-0.5 Mg alloy processed by hot extrusion, cold rolling, or high-pressure torsion10.1007/s11661-020-05797-y ↗
7. Processing of Zn-3Mg alloy by equal channel angular pressing for biodegradable metal implants10.1016/j.jksus.2017.07.008 ↗
8. Microstructural control of Zn alloy by melt spinning-A novel approach towards fabrication of advanced biodegradable biomedical materials10.1016/j.msea.2025.148347 ↗
9. Microstructural and mechanical evaluation of rapidly solidified Mg–Zn–Ca–Mn and Mg–Zn–Ca–Zr melt-spun alloys10.1002/adem.202501680 ↗
10. Microstructure, mechanical properties and fracture behavior of as-extruded Zn–Mg binary alloys10.1007/s40195-017-0585-4 ↗
11. Potential biodegradable Zn-Cu binary alloys developed for cardiovascular implant applications10.1016/j.jmbbm.2017.05.013 ↗
12. Fabrication, mechanical properties and in vitro degradation behavior of newly developed ZnAg alloys for degradable implant applications10.1016/j.msec.2017.04.023 ↗
13. Abnormal effect of Mn addition on the mechanical properties of as-extruded Zn alloys10.1016/j.msea.2017.06.037 ↗
14. Structural characteristics and in vitro biodegradation of a novel Zn-Li alloy prepared by induction melting and hot rolling10.1007/s11661-016-3901-0 ↗
15. The suitability of Zn–1.3% Fe alloy as a biodegradable implant material10.3390/met8030153 ↗
16. Evaluation of wrought Zn–Al alloys (1, 3, and 5 wt% Al) through mechanical and in vivo testing for stent applications10.1002/jbm.b.33850 ↗
17. Precipitation induced room temperature superplasticity in Zn-Cu alloys10.1016/j.matlet.2019.02.084 ↗
18. Microstructure of biodegradable Zn-Fe alloys and mechanical and corrosion properties10.1007/s11837-020-04317-y ↗
19. Overview of porous magnesium-based scaffolds: development, properties and biomedical applications10.1088/2752-5724/ad9493 ↗
20. Effect of cumulative strain on the microstructural and mechanical properties of Zn-0.02 wt% Mg alloy wires during room-temperature drawing process10.1016/j.jallcom.2018.01.059 ↗
21. Flow stress stabilization of Zn-Cu-Mn-Mg alloys using thermomechanical processing10.1016/j.matchar.2022.111928 ↗
22. Baker · 1992 · 501
23. Improved biocompatibility of Zn–Ag-based stent materials by microstructure refinement10.1016/j.actbio.2022.03.047 ↗
24. Towards revealing key factors in mechanical instability of bioabsorbable Zn-based alloys for intended vascular stenting10.1016/j.actbio.2020.01.028 ↗
25. Can zinc alloys be strengthened by grain refinement? A critical evaluation of the processing of low-alloyed binary zinc alloys using ECAP10.1016/j.msea.2019.01.117 ↗
26. vitro corrosion and in vivo response to zinc implants with electropolished and anodized surfaces10.1021/acsami.9b05370 ↗
27. Additive manufacturing of zinc-based biomaterials: Fabrication, performance and property evaluation10.1016/j.jmrt.2025.04.127 ↗
28. High-performance hot-warm rolled Zn-0.8 Li alloy with nano-sized metastable precipitates and sub-micron grains for biodegradable stents10.1016/j.jmst.2019.06.009 ↗
29. Microstructure and mechanical properties of extruded and caliber rolled biodegradable Zn-0.8 Mn-0.4 Ag alloy with high ductility10.1016/j.msea.2019.138543 ↗
30. Microstructure, mechanical properties and creep behaviour of extruded Zn-xLi (x= 0.1, 0.3 and 0.4) alloys for biodegradable vascular stent applications10.1016/j.msea.2020.139082 ↗
31. Novel high-strength, low-alloys Zn-Mg (< 0.1 wt% Mg) and their arterial biodegradation10.1016/j.msec.2017.11.021 ↗
32. Enhancement in mechanical and corrosion resistance properties of a biodegradable Zn-Fe alloy through second phase refinement10.1016/j.msec.2020.111197 ↗
33. Novel Zn-based alloys for biodegradable stent applications: Design, development and in vitro degradation10.1016/j.jmbbm.2016.03.018 ↗
34. Tailoring the mechanical and degradation performance of Mg-2.0 Zn-0.5 Ca-0.4 Mn alloy through microstructure design10.1007/s11837-020-04085-9 ↗
35. Current status and recent advances in magnesium-matrix syntactic foams: preparation, mechanical properties, and corrosion behavior10.1016/j.jmrt.2024.05.191 ↗
36. Effect of second-phase particle morphology on grain growth kinetics10.1016/j.actamat.2009.07.025 ↗
37. Enhanced mechanical properties and microstructural stability of ultrafine-grained biodegradable Zn–Li–Mn–Mg–Cu alloys produced by rapid solidification and high-pressure torsion10.1016/j.msea.2023.146027 ↗
38. Dynamic microstructural changes during hot extrusion and mechanical properties of a Mg–5.0 Zn–0.9 Y–0.16 Zr (wt%) alloy10.1016/j.msea.2011.01.103 ↗
39. Biodegradable Zn-1.5 Cu-1.5 Ag alloy with anti-aging ability and strain hardening behavior for cardiovascular stents10.1016/j.msec.2020.111172 ↗
40. Microstructure and mechanical properties of Zn–15Al-based ternary and quaternary alloys10.1016/j.msea.2014.02.047 ↗
41. Microstructure and mechanical properties of a high-Zn aluminum alloy prepared by melt spinning and extrusion10.1016/j.jallcom.2019.152990 ↗
42. Grain refinement mechanism and its effect on mechanical properties and biodegradation behaviors of Zn alloys–A review10.1016/j.jmrt.2023.04.219 ↗
43. Grain boundary segregation engineering in metallic alloys: A pathway to the design of interfaces10.1016/j.cossms.2014.06.002 ↗
44. Fine-tuning of mechanical properties in a Zn–Ag–Mg alloy via cold plastic deformation process and post-deformation annealing
45. Effect of Mg content on the microstructure, texture, and mechanical performance of hypoeutectic extruded Zn-Mg alloys10.1016/j.jallcom.2024.177155 ↗
46. Influence of strain rate and crystallographic orientation on dynamic recrystallization of pure Zn during room-temperature compression10.1016/j.jmst.2020.12.077 ↗
47. 380 MPa-30% grade biodegradable Zn-Mn-Mg-Ca alloy: Bimodal grain structure, large work-hardening strain, and enhanced biocompatibility10.1016/j.actbio.2024.12.050 ↗
48. Effect of second phase particles on grain refinement during equal-channel angular pressing of an Al–Mg–Mn alloy10.1016/j.actamat.2011.10.023 ↗
49. The rapid solidification processing of materials: science, principles, technology, advances, and applications10.1007/s10853-009-3995-5 ↗
50. Mechanical properties and Hall-Petch relationship of the extruded Mg-Zn-Y alloys with different volume fractions of icosahedral phase10.1016/j.jallcom.2018.08.121 ↗
51. Optimization of mechanical properties and corrosion resistance of Zn-0.4 Mn-0.8 Li alloy using the hot rolling process10.1016/j.jmst.2022.10.055 ↗
52. Fabrication and characterization of biodegradable Zn-Cu-Mn alloy micro-tubes and vascular stents: Microstructure, texture, mechanical properties and corrosion behavior10.1016/j.actbio.2022.07.049 ↗
53. Development of high strength and ductile Zn-Al-Li alloys for potential use in bioresorbable medical devices10.1016/j.msec.2021.111897 ↗
54. Significant ductility enhancement for high thermal conductivity Mg-2Sn-2.3 La alloy via Zn addition10.1016/j.msea.2024.147343 ↗
55. Towards increased strength and retained ductility of Zn-Mg-(Ag) materials for medical devices by adopting powder metallurgy processing routes10.1016/j.jmrt.2025.06.185 ↗
56. Achieving high strength and antibacterial Zn−4Ag−Mn alloy with homogenous corrosion behavior via high-pressure solid solution10.1016/S1003-6326(24)66537-4 ↗
57. Vitro Evaluation of the Feasibility of Commercial Zn Alloys as Biodegradable Metals10.1016/j.jmst.2016.06.003 ↗
58. Effect of Mn on microstructures and properties of backward extruded Zn-0.5 Mg alloys10.1016/j.jmrt.2025.01.148 ↗
59. Microstructures, mechanical properties and in vitro corrosion behavior of biodegradable Zn alloys microalloyed with Al, Mn, Cu, Ag and Li elements10.1016/j.jmst.2021.06.049 ↗
60. Long-term surveillance of zinc implant in murine artery: Surprisingly steady biocorrosion rate10.1016/j.actbio.2017.05.045 ↗
61. The effects of β-TCP on mechanical properties, corrosion behavior and biocompatibility of β-TCP/Zn-Mg composites10.1016/j.msec.2019.110397 ↗
62. Significant improvement in plasticity and degradation rate of Zn-0.2 Mn alloy by room-temperature rotary swaging
63. The effects of Cu and Mn on the microstructure, mechanical, corrosion properties and biocompatibility of Zn–4Ag alloy10.1016/j.jmrt.2022.11.083 ↗
64. Dendritic growth and solute trapping in rapidly solidified Cu-based alloys10.1007/s11433-011-4256-6 ↗
65. 300 MPa grade high-strength ductile biodegradable Zn-2Cu-xMg (x= 0.08, 0.15, 0.5, 1) alloys: The role of Mg in bimodal grain formation10.1016/j.jmst.2024.09.021 ↗
66. Cold-Spray Deposition of Antibacterial Molybdenum Coatings on Poly (dimethylsiloxane10.1021/acsabm.4c01380 ↗
67. A high-strength and high-ductility Zn–Ag alloy achieved through trace Mg addition and ECAP10.1016/j.msea.2023.145381 ↗
68. The grain refining mechanism of cast zinc through silver inoculation10.1016/j.actamat.2014.07.026 ↗
69. Magnesium-based nanocomposites: a review from mechanical, creep and fatigue properties10.1016/j.jma.2023.08.005 ↗
70. Regulating mechanical properties and degradation behavior of biodegradable Zn–0.6Mg alloy via ECAP plus cold rolling10.1016/j.jallcom.2022.168487 ↗