Mechanical Investigation of Kenaf/Carbon Hybrid Composites for Building and Construction Applications
Source abstract
Abstract
Single-kenaf fiber-reinforced polymer composites are typically characterized by relatively low strength and stiffness properties that make them unsuitable for structural applications. However, they are lightweight, economical, and ecofriendly. This paper presents a study on the manufacturing and mechanical characterization of bidirectional kenaf (K) fiber-reinforced epoxy composites hybridized with carbon (C) fibers in various stacking sequences and the effects of hybridization on salient physical and mechanical properties. Single and hybrid fiber composites were fabricated utilizing the vacuum infusion molding technique. The density, tensile, flexural, and interlaminar shear properties in hybrid composites increased significantly when carbon fiber volume increased from 9% to 16%. Stacking sequences in a hybrid affected the mechanical properties of the composites. The highest tensile strength and modulus were shown by the seven-layer hybrid composite with an alternate K/C stacking sequence and C layers as skin layers, i.e., C/K/C/K/C/K/C, among all tested hybrid composites. Sandwich design in the hybrid (C2/K3/C2) had higher flexural strength (+300%), flexural modulus (+414%), interlaminar shear strength (+278%), lower water absorption (−46%), and thickness swelling (−30%) compared to single-fiber kenaf/epoxy composites. Density increased by 5% in hybrid composites. The highest fracture toughness (+134%) was achieved using the dual sandwich design structure hybrid (C/K2/C2/K2/C). The developed composite has applications in stairways, walkways, and bridges.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Natural Fiber Reinforced Composites · Cellular and Composite Structures · Wood Treatment and Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Faculty of Engineering, Dept. of Mechanical Engineering, Univ. Teknologi PETRONAS, Perak 32610, Malaysia.
Faculty of Engineering, Dept. of Mechanical Engineering, Univ. Teknologi PETRONAS, Perak 32610, Malaysia (corresponding author).
Faculty of Engineering and Natural Sciences, Dept. of Mechanical Engineering, Istanbul Health and Technology Univ., Istanbul 34015, Turkey. ORCID: .
Faculty of Engineering, Dept. of Mechanical Engineering, Univ. Teknologi PETRONAS, Perak 32610, Malaysia. ORCID: .
References (50)
Show source-provided references
1. Adachi, T., M. Arai, N. Sakabe, and H. Matsumoto. 2000. “Evaluation of dynamic fracture toughness of unidirectional CFRP laminates.” JSME Int J., Ser. A 43 (2): 179–185. https://doi.org/10.1299/jsmea.43.179.10.1299/jsmea.43.179 ↗
2. Afendi, M., W. M. Banks, and D. Kirkwood. 2005. “Bubble free resin for infusion process.” Composites, Part A 36 (6): 739–746. https://doi.org/10.1016/j.compositesa.2004.10.030.10.1016/j.compositesa.2004.10.030 ↗
3. Aisyah, H. A., M. T. Paridah, A. Khalina, S. M. Sapuan, M. S. Wahab, O. B. Berkalp, C. H. Lee, and S. H. Lee. 2018. “Effects of fabric counts and weave designs on the properties of laminated woven kenaf/carbon fibre reinforced epoxy hybrid composites.” Polymers 10 (12): 1320. https://doi.org/10.3390/polym10121320.10.3390/polym10121320 ↗
4. Aisyah, H. A., 2019. “Thermal properties of woven kenaf/carbon fibre-reinforced epoxy hybrid composite panels.” Int. J. Polym. Sci. 2019: 8. https://doi.org/10.1155/2019/5258621.10.1155/2019/5258621 ↗
5. Akil, H. M., M. F. Omar, A. A. M. Mazuki, S. Safiee, Z. A. M. Ishak, and A. Abu Bakar. 2011. “Kenaf fiber reinforced composites: A review.” Mater. Des. 32 (8–9): 4107–4121. https://doi.org/10.1016/j.matdes.2011.04.008.10.1016/j.matdes.2011.04.008 ↗
6. ASTM. 2014. Standard test method for tensile properties of polymer matrix composite materials. ASTM D3039/D3039M-08. Annual Book of ASTM Standards. West Conshohocken, PA: ASTM.
7. ASTM. 2017. Standard test methods for flexural properties of unreinforced and reinforced plastics and electrical insulating materials. ASTM D790-17. Annual Book of ASTM Standards. West Conshohocken, PA: ASTM.
8. ASTM. 2018a. Standard test method for water absorption of plastics. ASTM D570-98. Annual Book of ASTM Standards. West Conshohocken, PA: ASTM.
9. ASTM. 2018b. Standard test method for ignition loss of cured reinforced resins. ASTM D2584-18. Annual Book of ASTM Standards. West Conshohocken, PA: ASTM.
10. ASTM. 2019. Standard test method for determination of the mode II interlaminar fracture toughness of unidirectional fiber-reinforced polymer matrix composites. ASTM D7905/D7905M-19e1. Annual Book of ASTM Standards. West Conshohocken, PA: ASTM.
11. ASTM. 2020. Standard test methods for density and specific gravity (relative density) of plastics by displacement. ASTM D792-20. Annual Book of ASTM Standards. West Conshohocken, PA: ASTM.
12. ASTM. 2022. Standard test method for short-beam strength of polymer matrix composite materials and their laminates. ASTM D2344/D2344M-22. Annual Book of ASTM Standards. West Conshohocken, PA: ASTM.
13. Baillie, C. 2005. Green composites: Polymer composites and the environment. Boca Raton, FL: CRC Press.10.1201/9781439823408 ↗
14. Benmokrane, B., M. Hassan, M. Robert, P. V. Vijay, and A. Manalo. 2020. “Effect of different constituent fiber, resin, and sizing combinations on alkaline resistance of basalt, carbon, and glass FRP bars.” J. Compos. Constr. 24 (3): 04020010. https://doi.org/10.1061/(ASCE)CC.1943-5614.0001009.10.1061/(ASCE)CC.1943-5614.0001009 ↗
15. 10.1061/JCCOF2.CCENG-389710.1061/JCCOF2.CCENG-3897 ↗
16. De Rosa, I. M., C. Santulli, and F. Sarasini. 2010. “Mechanical and thermal characterization of epoxy composites reinforced with random and quasi-unidirectional untreated Phormium tenax leaf fibers.” Mater. Des. 31 (5): 2397–2405. https://doi.org/10.1016/j.matdes.2009.11.059.10.1016/j.matdes.2009.11.059 ↗
17. Fan, Z., M. H. Santare, and S. G. Advani. 2008. “Interlaminar shear strength of glass fiber reinforced epoxy composites enhanced with multi-walled carbon nanotubes.” Composites, Part A 39 (3): 540–554. https://doi.org/10.1016/j.compositesa.2007.11.013.10.1016/j.compositesa.2007.11.013 ↗
18. Gibson, R. F. 2016. Principles of composite material mechanics. Boca Raton, FL: CRC Press.10.1201/b19626 ↗
19. Hashemi, F., L. Brancheriau, and P. M. Tahir. 2018. “Hybridization and yarns configuration effects on flexural dynamic and static properties of pultruded hybrid kenaf/glass fiber composites.” Composites, Part A 112: 415–422. https://doi.org/10.1016/j.compositesa.2018.05.008.10.1016/j.compositesa.2018.05.008 ↗
20. Hashemi, F., P. M. Tahir, B. Madsen, M. Jawaid, D. L. Majid, L. Brancheriau, and A. H. Juliana. 2016. “Volumetric composition and shear strength evaluation of pultruded hybrid kenaf/glass fiber composites.” J. Compos. Mater. 50 (17): 2291–2303. https://doi.org/10.1177/0021998315602948.10.1177/0021998315602948 ↗
21. Hughes, M. 2012. “Defects in natural fibres: Their origin, characteristics and implications for natural fibre-reinforced composites.” J. Mater. Sci. 47 (2): 599–609. https://doi.org/10.1007/s10853-011-6025-3.10.1007/s10853-011-6025-3 ↗
22. Jambari, S., M. Y. Yahya, M. R. Abdullah, and M. Jawaid. 2017. “Woven kenaf/kevlar hybrid yarn as potential fiber reinforced for anti-ballistic composite material.” Fibers Polym. 18 (3): 563–568. https://doi.org/10.1007/s12221-017-6950-0.10.1007/s12221-017-6950-0 ↗
23. Kang, M. K., W. I. Lee, and H. T. Hahn. 2000. “Formation of microvoids during resin-transfer molding process.” Compos. Sci. Technol. 60 (12–13): 2427–2434. https://doi.org/10.1016/S0266-3538(00)00036-1.10.1016/S0266-3538(00)00036-1 ↗
24. Khayyam, H., M. Naebe, A. S. Milani, S. M. Fakhrhoseini, A. Date, B. Shabani, S. Atkiss, S. Ramakrishna, B. Fox, and R. N. Jazar. 2021. “Improving energy efficiency of carbon fiber manufacturing through waste heat recovery: A circular economy approach with machine learning.” Energy 225: 120113. https://doi.org/10.1016/j.energy.2021.120113.10.1016/j.energy.2021.120113 ↗
25. Kureemun, U., M. Ravandi, L. Q. N. Tran, W. S. Teo, T. E. Tay, and H. P. Lee. 2018. “Effects of hybridization and hybrid fibre dispersion on the mechanical properties of woven flax-carbon epoxy at low carbon fibre volume fractions.” Composites, Part B 134: 28–38. https://doi.org/10.1016/j.compositesb.2017.09.035.10.1016/j.compositesb.2017.09.035 ↗
26. Lundström, T. S., and B. R. Gebart. 1994. “Influence from process parameters on void formation in resin transfer molding.” Polym. Compos. 15 (1): 25–33. https://doi.org/10.1002/pc.750150105.10.1002/pc.750150105 ↗
27. Lundström, T. S., B. R. Gebart, and C. Y. Lundemo. 1993. “Void formation in RTM.” J. Reinf. Plast. Compos. 12 (12): 1339–1349. https://doi.org/10.1177/073168449301201207.10.1177/073168449301201207 ↗
28. Machado, J. J. M., E. A. S. Marques, R. D. S. G. Campilho, and L. F. M. da Silva. 2017. “Mode II fracture toughness of CFRP as a function of temperature and strain rate.” Composites, Part B 114: 311–318. https://doi.org/10.1016/j.compositesb.2017.02.013.10.1016/j.compositesb.2017.02.013 ↗
29. Maharana, S. M., M. K. Pandit, and A. K. Pradhan. 2021. “Influence of fumed silica nanofiller and stacking sequence on interlaminar fracture behaviour of bidirectional jute-kevlar hybrid nanocomposite.” Polym. Test. 93: 106898. https://doi.org/10.1016/j.polymertesting.2020.106898.10.1016/j.polymertesting.2020.106898 ↗
30. Malik, K., F. Ahmad, and E. Gunister. 2021a. “A review on the kenaf fiber reinforced thermoset composites.” Appl. Compos. Mater. 28: 491–528. https://doi.org/10.1007/s10443-021-09871-5.
31. Malik, K., F. Ahmad, and E. Gunister. 2021b. “Drilling performance of natural fiber reinforced polymer composites: A review.” J. Nat. Fibers 19: 4761–4779. https://doi.org/10.1080/15440478.2020.1870624.10.1080/15440478.2020.1870624 ↗
32. Malik, K., F. Ahmad, E. Gunister, T. Nakato, E. Mouri, M. Muhammad, and S. Ali. 2021c. “A review of flax fiber reinforced thermoset polymer composites: Structure and mechanical performance.” J. Nat. Fibers. 14: 9656–9680. https://doi.org/10.1080/15440478.2021.1990182.
33. Malik, K., F. Ahmad, W. T. Keong, and E. Gunister. 2022a. “The effects of drilling parameters on thrust force, temperature and hole quality of glass fiber reinforced polymer composites.” Polym. Polym. Compos. 30: 096739112211311. https://doi.org/10.1177/09673911221131113.10.1177/09673911221131113 ↗
34. Malik, K., F. Ahmad, N. A. Yunus, E. Gunister, S. Ali, and A. Raza. 2023a. “Physical and mechanical properties of kenaf/flax hybrid composites.” J. Appl. Polym. Sci. 140 (5): e53421. https://doi.org/10.1002/app.53421.10.1002/app.53421 ↗
35. Malik, K., F. Ahmad, N. A. Yunus, E. Gunister, M. S. I. S. Dawood, S. Ali, C. S. Mani, M. Syahir, and A. L. Larry. 2022b. “The hybridization effects of glass and carbon fibers on the mechanical properties of kenaf mat/epoxy composites.” J. Nat. Fibers 19: 15432–15447. https://doi.org/10.1080/15440478.2022.2127437.10.1080/15440478.2022.2127437 ↗
36. Malik, K., F. Ahmad, N. Yunus, E. Gunister, T. Nakato, E. Mouri, and S. Ali. 2021d. “A review of flax fiber reinforced thermoset polymer composites: Thermal–physical properties, improvements and application.” J. Nat. Fibers. 19 (15): 10412–10430. https://doi.org/10.1080/15440478.2021.1993507.
37. Malik, K., F. Ahmad, N. A. Yunus, T. Nakato, E. Mouri, S. Dawood, and I. R. Memon. 2023b. “A new method of reinforcing graphene nanoplatelets in glass/epoxy composites.” Materialwiss. Werkstofftech. 54 (9): 1157–1166. https://doi.org/10.1002/mawe.202100374.10.1002/mawe.202100374 ↗
38. 10.1201/978142000598110.1201/9781420005981 ↗
39. Miyagawa, H., C. Sato, and K. Ikegami. 2001. “Experimental determination of fracture toughness of CFRP in mode II by Raman spectroscopy.” Appl. Compos. Mater. 8 (1): 25–41. https://doi.org/10.1023/A:1008910114515.10.1023/A:1008910114515 ↗
40. Naveen, J., M. Jawaid, E. S. Zainudin, M. T. H. Sultan, and R. Yahaya. 2019. “Mechanical and moisture diffusion behaviour of hybrid Kevlar/Cocos nucifera sheath reinforced epoxy composites.” J. Mater. Res. Technol. 8 (1): 1308–1318. https://doi.org/10.1016/j.jmrt.2018.07.023.10.1016/j.jmrt.2018.07.023 ↗
41. Ramesh, M. 2016. “Kenaf (Hibiscus cannabinus L.) fibre based bio-materials: A review on processing and properties.” Prog. Mater Sci. 78–79: 1–92. https://doi.org/10.1016/j.pmatsci.2015.11.001.10.1016/j.pmatsci.2015.11.001 ↗
42. Sanjay, M. R., G. R. Arpitha, P. Senthamaraikannan, M. Kathiresan, M. A. Saibalaji, and B. Yogesha. 2019. “The hybrid effect of jute/kenaf/E-glass woven fabric epoxy composites for medium load applications: Impact, inter-laminar strength, and failure surface characterization.” J. Nat. Fibers 16 (4): 600–612. https://doi.org/10.1080/15440478.2018.1431828.10.1080/15440478.2018.1431828 ↗
43. Singh, K., D. Das, R. K. Nayak, S. Khandai, R. Kumar, and B. C. Routara. 2020. “Effect of silanizion on mechanical and tribological properties of kenaf-carbon and kenaf-glass hybrid polymer composites.” Mater. Today: Proc. 26: 2094–2098. https://doi.org/10.1016/j.matpr.2020.02.452.
44. Srivastava, V. K., T. Gries, D. Veit, T. Quadflieg, B. Mohr, and M. Kolloch. 2017. “Effect of nanomaterial on mode I and mode II interlaminar fracture toughness of woven carbon fabric reinforced polymer composites.” Eng. Fract. Mech. 180: 73–86. https://doi.org/10.1016/j.engfracmech.2017.05.030.10.1016/j.engfracmech.2017.05.030 ↗
45. Subramaniyan, A. K., and C. T. Sun. 2006. “Enhancing compressive strength of unidirectional polymeric composites using nanoclay.” Composites, Part A 37 (12): 2257–2268. https://doi.org/10.1016/j.compositesa.2005.12.027.10.1016/j.compositesa.2005.12.027 ↗
46. Tamrakar, S., A. Kiziltas, D. Mielewski, and R. Zander. 2021. “Characterization of kenaf and glass fiber reinforced hybrid composites for underbody shield applications.” Composites, Part B 216: 108805. https://doi.org/10.1016/j.compositesb.2021.108805.10.1016/j.compositesb.2021.108805 ↗
47. Yahaya, R., S. M. Sapuan, M. Jawaid, Z. Leman, and E. S. Zainudin. 2014. “Mechanical performance of woven kenaf-kevlar hybrid composites.” J. Reinf. Plast. Compos. 33 (24): 2242–2254. https://doi.org/10.1177/0731684414559864.10.1177/0731684414559864 ↗
48. Yahaya, R., S. M. Sapuan, M. Jawaid, Z. Leman, and E. S. Zainudin. 2015. “Effect of layering sequence and chemical treatment on the mechanical properties of woven kenaf–aramid hybrid laminated composites.” Mater. Des. 67: 173–179. https://doi.org/10.1016/j.matdes.2014.11.024.10.1016/j.matdes.2014.11.024 ↗
49. Yahaya, R., S. M. Sapuan, M. Jawaid, Z. Leman, and E. S. Zainudin. 2016. “Effect of fibre orientations on the mechanical properties of kenaf–aramid hybrid composites for spall-liner application.” Def. Technol. 12 (1): 52–58. https://doi.org/10.1016/j.dt.2015.08.005.10.1016/j.dt.2015.08.005 ↗
50. Zhong, Y., L. Q. N. Tran, U. Kureemun, and H. P. Lee. 2017. “Prediction of the mechanical behavior of flax polypropylene composites based on multi-scale finite element analysis.” J. Mater. Sci. 52 (9): 4957–4967. https://doi.org/10.1007/s10853-016-0733-7.10.1007/s10853-016-0733-7 ↗