Experimental Investigation of the Lateral Load–Carrying Capacity of a Developed GFRP-Reinforced TL-5 Bridge Barrier Using Special Profile Hooked Bars
Source abstract
Abstract
Old concrete bridge barriers suffer from corrosion-induced degradation due to the effects of freeze–thaw cycles and the application of winter deicing salt. To replace such deteriorated bridge barriers while aiming to reduce maintenance costs and improve their life expectancy, rust-free high-modulus (HM) glass fiber–reinforced polymer (GFRP) bars with 180° hooks are utilized as primary reinforcement in the barrier wall. A proposed TL-5 bridge barrier developed in this research incorporated 15M and 13M GFRP bars as vertical (transverse) reinforcement in the barrier front and back faces at a 300-mm spacing, respectively, and 15M GFRP bars as horizontal (longitudinal) reinforcement in the barrier wall. The connection between the deck slab and the barrier wall utilized GFRP bars with 180° hooks for proper anchorage. To study the structural behavior, the crack pattern and the ultimate load–carrying capacity of the proposed barrier wall under an equivalent transverse vehicle collision force, a 40-m-long GFRP-reinforced TL-5 barrier was constructed and statically tested to failure under transverse line load at interior and end locations. While trapezoidal flexural cracks were developed at the traffic side of the barrier wall during loading, punching shear crack occurred at the loading location, leading to barrier failure. The experimental ultimate load–carrying capacities of the barriers were observed to be far greater than the load capacity required by current design codes. GFRP bar strain and concrete strain readings at the barrier deck showed very low strains at failure compared to the material’s nominal failure strain. To study the pullout capacity of the GFRP bars with 180° hooks reinforcing the lower tapered portion of the barrier wall and embedment into the deck slab, a representative concrete slab with various embedded GFRP bars was constructed. Pullout tests on GFRP bars with straight ends, hooked ends, and hooked ends with unbonded straight portions of the bar were performed. The results showed that the average pullout capacities of the tested bars are far greater than the pullout capacity of 100 kN specified in current standards for TL-5 HM-GFRP concrete barriers. The GFRP bar’s experimental pullout capacity can be used to determine the resisting moment at the barrier deck connection for compliance with the code-specified factored applied moment at this location.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Concrete Corrosion and Durability · Structural Behavior of Reinforced Concrete · Transportation Safety and Impact Analysis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Ph.D. Candidate, Dept. of Civil Engineering, Ryerson Univ., Toronto, ON, Canada M5B 2K3.
Professor, Dept. of Civil Engineering, Ryerson Univ., Toronto, ON, Canada M5B 2K3.
Director, Construction Material Testing and Engineering, Inc., 160 Centennial Pkwy. North, Unit 5, Hamilton, ON, Canada L8E 1H9; Adjunct Professor, Ryerson Univ., Toronto, ON, Canada (corresponding author).
References (26)
Show source-provided references
1. AASHTO · 2009
2. AASHTO · 2017
3. Alberson D. · 2005 · 1
4. Alberson D. W. Williams C. Boyd and M. Bloschock. 2005b. “Analysis and testing of the Florida Jersey safety shaped bridge rail.” In Proc. TRB 2005 Annual Meeting 1–24. Washington DC: Transportation Research Board.
5. 10.1061/(ASCE)BE.1943-5592.000060610.1061/(ASCE)BE.1943-5592.0000606 ↗
6. A new punching shear equation for two-way concrete slabs reinforced with FRP bars
7. New approach for punching shear capacity prediction of fiber reinforced polymer reinforced concrete flat slabs
8. El-Ghandour A. K. Pilakoutas and P. Waldron. 2000. “Punching shear behavior and design of FRP RC flat slabs.” In Proc. Int. Workshop on Punching Shear Capacity of RC Slab 359–366. Stockholm Sweden: Royal Institute of Technology.
9. Punching shear capacity of double layer FRP grid reinforced slabs
10. 10.4334/IJCSM.2008.2.1.05710.4334/IJCSM.2008.2.1.057 ↗
11. JSCE (Japan Society of Civil Engineers) · 1997 · 325
12. Determination of materials design values for the use of fibre-reinforced polymer composites in civil infrastructure
13. Khederzadeh H. and K. Sennah. 2014a. “AASHTO-LRFD yield-line analysis for flexural resistance of bridge barrier wall: Re-visited.” In Proc. 9th Int. Conf. on Short and Medium Span Bridges 1–10. Montreal QC Canada: Canadian Society for Civil Engineering.
14. 10.1139/cjce-2013-039410.1139/cjce-2013-0394 ↗
15. Khederzadeh H. and K. Sennah. 2014c. “Experimental investigation of steel-reinforced TL-5 bridge barriers subjected to transverse static loading.” In Proc. 9th Int. Conf. on Short and Medium Span Bridges 1–9. Montreal QC Canada: Canadian Society for Civil Engineering.
16. Khederzadeh H. and K. Sennah. 2015. “Finite-element modelling of bridge barrier walls reinforced with GFRP bars and subjected to equivalent transverse impact loading.” In Proc. 4th Specialty Conf. on Material Engineering and Applied Mechanics 1–10. Montreal QC Canada: Canadian Society for Civil Engineering.
17. 10.1061/(ASCE)1084-0702(2009)14:1(66)10.1061/(ASCE)1084-0702(2009)14:1(66) ↗
18. 10.1061/(ASCE)1090-0268(2000)4:3(154)10.1061/(ASCE)1090-0268(2000)4:3(154) ↗
19. Punching of two-way concrete slabs with fiber-reinforced polymer reinforcing bars or grids
20. Rostami M. K. Sennah and S. Dehnadi. 2016. “Experimental study on the capacity of barrier-deck anchorage in MTQ PL-3 barrier reinforced with HM-GFPP bars with headed ends.” In Proc. 5th Int. Structural Specialty Conf. 1–10. London Canada: Canadian Society for Civil Engineering.
21. Sennah K. B. Juette A. Weber and C. Witt. 2011. “Vehicle crash testing of a GFRP-reinforced TL-5 concrete bridge barrier.” In Proc. 4th Int. Conf. on Durability and Sustainability of Fibre Reinforced Polymer Composites for Construction and Rehabilitation 417–424. Sherbrook QC Canada: Univ. of Sherbrook.
22. 10.1139/cjce-2013-039310.1139/cjce-2013-0393 ↗
23. 10.1061/(ASCE)BE.1943-5592.000118410.1061/(ASCE)BE.1943-5592.0001184 ↗
24. Sennah K. E. Tropynina S. Goremykin M. Lam and S. Lucic. 2010. “Concrete bridge barriers reinforced with GFRP bars with headed ends.” In Proc. 8th Int. Conf. on Short and Medium Span Bridges 1–10. Montreal QC Canada: Canadian Society for Civil Engineering.
25. Sennah K. E. Tropynina and Z. Mahmoud. 2012. “Ultimate load tests on TL-5 bridge barrier reinforced with GFRP bars with ribbed surface and headed ends.” In Proc. 3rd Int. Structural Specialty Conf. 1–10. Edmonton Canada: Canadian Society for Civil Engineering.
26. TemCorp Industries. 2016. “GFRP data sheet.” Accessed January 5 2016. www.temcorp.ca.