Calibration of the FRP Resistance Reduction Factor for FRP-Confined Reinforced Concrete Building Columns
Source abstract
Abstract
This paper presents a reliability-based methodology for calibration of the fiber-reinforced polymer (FRP) resistance reduction factor used in the design of FRP-confined RC columns designed based on current guidelines. The Monte Carlo simulation technique was employed to generate a large population of design cases based on frequency of the design variables. Within the code calibration procedure, a comprehensive probabilistic study on variability of resistance, i.e., compressive strength of FRP-confined RC columns considering uncertainties in material properties, section dimension, and the model error, was carried out. It was shown that statistics of resistance and consequently reliability of the ultimate limit state are highly dependent on the variability of confinement model and the FRP strain efficiency factor. Furthermore, for RC columns with spiral confinement, the current FRP resistance reduction factor advised by current guidelines should be reduced. Sensitivity of the FRP resistance reduction factor to some selected target reliability indexes was also studied. In addition, a confinement-dependent formula for determining the FRP resistance reduction factor was proposed.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Structural Behavior of Reinforced Concrete · Concrete Corrosion and Durability · Structural Load-Bearing Analysis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Research Fellow, School of Engineering, Civil Engineering, RMIT Univ., Melbourne, VIC 3001, Australia.
References (100+)
Show source-provided references
1. ACI (American Concrete Institute). (2008). “Guide for the design and construction of externally bonded FRP systems for strengthening concrete structures.” ACI 440 Farmington Hills MI.
2. ACI (American Concrete Institute). (2011). “Building code requirements for structural concrete and commentary.” ACI 318 Farmington Hills MI.
3. 10.3989/mc.2010.4560810.3989/mc.2010.45608 ↗
4. 10.1016/j.compositesb.2006.06.02110.1016/j.compositesb.2006.06.021 ↗
5. Atadero R. A. (2006). “Development of load and resistance factor design for FRP strengthening of reinforced concrete structures.” Ph.D. thesis Univ. of California San Diego.
6. 10.1016/j.compositesb.2007.06.00410.1016/j.compositesb.2007.06.004 ↗
7. 10.1016/j.compstruct.2008.07.00110.1016/j.compstruct.2008.07.001 ↗
8. 10.1139/l07-03410.1139/l07-034 ↗
9. Statistical analysis of the compressive strength of concrete in structures
10. 10.1007/BF0115754810.1007/BF01157548 ↗
11. 10.1177/073168440935519910.1177/0731684409355199 ↗
12. 10.1016/j.conbuildmat.2004.05.01210.1016/j.conbuildmat.2004.05.012 ↗
13. Comparison of confinement models for fiber-reinforced polymer-wrapped concrete
14. 10.1680/stbu.2009.162.5.30110.1680/stbu.2009.162.5.301 ↗
15. Bournonville M. Dahnke J. and Darwin D. (2004). “Statistical analysis of the mechanical properties and weight of reinforcing bars.” Univ. of Kansas Lawrence KS.
16. Bullo S. (2003). “Experimental study of the effects of the ultimate strain of fiber reinforced plastic jackets on the behavior of confined concrete.” Proc. 2nd Int. Conf. on Composite in Construction Univ. of Calabria Rende Italy 465–470.
17. Cairns S. W. (2001). “Circular concrete columns externally reinforced with pre-fabricated carbon polymer shells.” Master thesis Univ. of Toronto Toronto.
18. Axial behavior and modeling of confined small-, medium-, and large-scale circular sections with carbon fiber-reinforced polymer jackets
19. 10.1016/j.compstruct.2014.07.03210.1016/j.compstruct.2014.07.032 ↗
20. CEB (Comité Euro-International du Béton). (2010). “fib model code 2010 first complete draft.” Ernst & Sohn Lausanne Switzerland.
21. CEB (fédération internationale du béton). (2001). “Externally bonded FRP reinforcement for RC structures.” fib Bulletin 14 Lausanne Switzerland.
22. 10.1016/j.engstruct.2010.04.00110.1016/j.engstruct.2010.04.001 ↗
23. Ciupala M. Pilakoutas K. and Mortazavi A. (2007). “Effectiveness of FRP composites in confined concrete.” Proc. 8th Int. Symp. on Fiber Reinforced Polymer Reinforcement for Concrete Structures (FRPRCS-8) Univ. of Patras Patras Greece 1–10.
24. CSA (Canadian Standards Association). (2002). “Design and construction of building components with fibre-reinforced polymers.” CSA S-806 Mississauga ON Canada.
25. Cui C. (2009). “Behaviour of normal and high strength concrete confined with fibre reinforced polymers (FRP).” Ph.D. thesis Univ. of Toronto Toronto.
26. 10.1061/(ASCE)CC.1943-5614.000011610.1061/(ASCE)CC.1943-5614.0000116 ↗
27. De Lorenzis L. Micelli F. and La Tegola A. (2002). “Influence of specimen size and resin type on the behaviour of FRP-confined concrete cylinders.” 1st Int. Conf. on Advanced Polymer Composites for Structural Applications in Construction: Proc. Thomas Telford Southampton U.K. 231–240.10.1680/apcfsaic.31227.0024 ↗
28. 10.1061/(ASCE)1090-0268(2003)7:3(219)10.1061/(ASCE)1090-0268(2003)7:3(219) ↗
29. Demers M. and Neale K. (1994). “Developments in short and medium span bridge engineering.” 4th Int. Conf. on Short and Medium Span Bridges Canadian Society for Civil Engineering Montreal 895–905.
30. 10.1139/l98-06710.1139/l98-067 ↗
31. Dias da Silva V. and Santos J. (2001). “Strengthening of axially loaded concrete cylinders by surface composites.” Proc. Int. Conf.: Composites in Constructions A.A. Balkema Lisse Netherlands 257–262.
32. 10.1061/(ASCE)1090-0268(2009)13:2(113)10.1061/(ASCE)1090-0268(2009)13:2(113) ↗
33. 10.1061/(ASCE)0733-9445(2003)129:4(449)10.1061/(ASCE)0733-9445(2003)129:4(449) ↗
34. Ellingwood B. Galambos T. McGregor J. and Cornell C. (1980). “Development of a probability-based load criteria for American Standard A 58.” National Bureau of Standards Washington DC.10.6028/NBS.SP.577 ↗
35. 10.1016/j.conbuildmat.2011.10.02510.1016/j.conbuildmat.2011.10.025 ↗
36. Faella C. Realfonzo R. and Salerno N. (2004). “Sulla resistenza e deformazione di elementi in ca confinati con tessuti in FRP.” Proc. 9th National Congress L’ingegneria sismica in Italia ANIDIS Genova Italy 25–29.
37. 10.1680/macr.1982.34.121.19110.1680/macr.1982.34.121.191 ↗
38. 10.1016/S0008-8846(02)01085-210.1016/S0008-8846(02)01085-2 ↗
39. 10.1016/S0008-8846(02)01086-410.1016/S0008-8846(02)01086-4 ↗
40. He Z. and Jiang L. (2007). “Flexural reliability assessment of FRP-strengthened reinforced concrete beams designed by Chinese CECS-146 guideline.” Proc. 8th Int. Symp. on Fiber Reinforced Polymer Reinforcement for Concrete Structures (FRPRCS-8) Univ. of Patras Patras Greece 123–133.
41. 10.12989/sem.2004.18.2.16710.12989/sem.2004.18.2.167 ↗
42. 10.1061/(ASCE)0899-1561(2008)20:2(169)10.1061/(ASCE)0899-1561(2008)20:2(169) ↗
43. Jaffry S. A. D. (2001). “Concrete filled glass fibre reinforced polymer (GFRP) shells under concentric compression.” Master thesis Univ. of Toronto Toronto.
44. 10.1016/j.engstruct.2007.01.01010.1016/j.engstruct.2007.01.010 ↗
45. Joint Committee on Structural Safety. (2012). “Probabilistic model code.” Technical Univ. of Denmark Lyngby Denmark.
46. Kono S. Inazumi M. and Kaku T. (1998). “Evaluation of confining effects of CFRP sheets on reinforced concrete members.” Proc. 2nd Int. Conf. on Composites in Infrastructure Univ. of Arizona Tucson AZ 343–355.
47. Environmental aging of fiber-reinforced polymer-wrapped concrete cylinders
48. 10.1016/S0950-0618(03)00045-X10.1016/S0950-0618(03)00045-X ↗
49. 10.1061/(ASCE)1090-0268(2004)8:6(539)10.1061/(ASCE)1090-0268(2004)8:6(539) ↗
50. 10.1016/j.cemconcomp.2006.07.00710.1016/j.cemconcomp.2006.07.007 ↗
51. 10.1177/073168441243934710.1177/0731684412439347 ↗
52. 10.1061/(ASCE)CC.1943-5614.000037610.1061/(ASCE)CC.1943-5614.0000376 ↗
53. Investigation of the influence of the application path of confining pressure: Tests on actively confined and FRP-confined concretes
54. 10.1617/s11527-014-0358-810.1617/s11527-014-0358-8 ↗
55. Load and resistance factors for concrete design
56. Mastrapa J. (1997). “Effect of construction bond on confinement with fiber composites.” Master thesis Univ. of Central Florida Orlando FL.
57. Matthys S. Taerwe L. and Audenaert K. (1999). “Tests on axially loaded concrete columns confined by fiber reinforced polymer sheet wrapping.” Proc. FRPRCS-4 Baltimore 217–228.
58. Axial load behavior of large-scale columns confined with fiber-reinforced polymer composites
59. Melchers R. E. · 1999
60. 10.1016/j.compositesb.2012.09.05510.1016/j.compositesb.2012.09.055 ↗
61. Micelli F. Myers J. and Murthy S. (2001). “Effect of environmental cycles on concrete cylinders confined with FRP.” Proc. Int. Conf.: Composites in Constructions A.A. Balkema Lisse Netherlands 317–322.
62. 10.1061/(ASCE)1090-0268(1998)2:4(175)10.1061/(ASCE)1090-0268(1998)2:4(175) ↗
63. 10.1061/JSDEAG.000516110.1061/JSDEAG.0005161 ↗
64. 10.1061/(ASCE)CC.1943-5614.000006610.1061/(ASCE)CC.1943-5614.0000066 ↗
65. 10.1061/(ASCE)1090-0268(2002)6:3(162)10.1061/(ASCE)1090-0268(2002)6:3(162) ↗
66. Calibration of design code for buildings (ACI 318): Part 1—Statistical models for resistance
67. 10.1061/(ASCE)CC.1943-5614.000031510.1061/(ASCE)CC.1943-5614.0000315 ↗
68. Short-term tensile strength of carbon fiber-reinforced polymer laminates for flexural strengthening of concrete girders
69. Owen L. M. (1998). “Stress-strain behavior of concrete confined by carbon fiber jacketing.” Master thesis Univ. of Washington Seattle.
70. 10.1016/j.compositesb.2013.07.02510.1016/j.compositesb.2013.07.025 ↗
71. 10.1016/j.engstruct.2012.06.01010.1016/j.engstruct.2012.06.010 ↗
72. Axial compressive behavior of circular high-strength concrete-filled FRP tubes
73. Parretti R. and Nanni A. (2002). “Axial testing of concrete columns confined with carbon FRP: Effect of fiber orientation.” Proc. ICCI 2002 Tucson AZ 1–10.
74. Paula R. (2003). “Influência da geometria das secções no confinamento de pilares de betão armado com compósitos de CFRP.” Master thesis Universidade de Lisboa Lisbon Portugal.
75. 10.1061/(ASCE)1090-0268(2001)5:4(237)10.1061/(ASCE)1090-0268(2001)5:4(237) ↗
76. 10.1016/j.compstruct.2006.12.01010.1016/j.compstruct.2006.12.010 ↗
77. Picher F. Rochette P. and Labossiére P. (1996). “Confinement of concrete cylinders with CFRP.” Proc. 1st Int. Conf. on Composite Infrastructures Univ. of Arizona Tucson AZ 829–841.
78. 10.1061/(ASCE)1090-0268(2002)6:3(154)10.1061/(ASCE)1090-0268(2002)6:3(154) ↗
79. 10.1061/(ASCE)0733-9445(1995)121:7(1037)10.1061/(ASCE)0733-9445(1995)121:7(1037) ↗
80. 10.1139/l99-02210.1139/l99-022 ↗
81. 10.1016/j.compositesb.2011.01.02810.1016/j.compositesb.2011.01.028 ↗
82. Richart F. E. Brandtzaeg A. and Brown R. L. (1928). “A study of the failure of concrete under combined compressive stresses.” Univ. of Illinois Champaign IL.
83. Rocca S. (2007). “Experimental and analytical evaluation of FRP-confined large size reinforced concrete columns.” Ph.D. thesis Univ. of Missouri—Rolla Rolla MO.
84. Rochette P. and Labossiere P. (1996). “A plasticity approach for concrete columns confined with composite materials.” Proc. 2nd Int. Conf. on Advanced Composite Materials in Bridges and Structures Canadian Society of Civil Engineering Montreal 359–366.
85. Rousakis T. and Tepfers R. (2001). “Experimental investigation of concrete cylinders confined by carbon FRP sheets under monotonic and cyclic axial compressive load.” Division of Building Technology Chalmers Univ. of Technology Goteborg Sweden.
86. 10.1061/(ASCE)CC.1943-5614.000029510.1061/(ASCE)CC.1943-5614.0000295 ↗
87. 10.1061/(ASCE)0733-9445(1998)124:9(1025)10.1061/(ASCE)0733-9445(1998)124:9(1025) ↗
88. 10.1061/(ASCE)1090-0268(2006)10:3(244)10.1061/(ASCE)1090-0268(2006)10:3(244) ↗
89. 10.1061/(ASCE)0733-9445(1998)124:9(1025)10.1061/(ASCE)0733-9445(1998)124:9(1025) ↗
90. 10.1016/S1359-8368(00)00021-410.1016/S1359-8368(00)00021-4 ↗
91. Shehata I. Carneiro L. and Shehata L. (2007). “Strength of confined short concrete columns.” Proc. 8th Int. Symp. on Fiber Reinforced Polymer Reinforcement for Concrete Structures Univ. of Patras Patras Greece 1–10.
92. 10.1061/(ASCE)0899-1561(2006)18:3(334)10.1061/(ASCE)0899-1561(2006)18:3(334) ↗
93. 10.1061/(ASCE)CC.1943-5614.000035110.1061/(ASCE)CC.1943-5614.0000351 ↗
94. 10.1061/(ASCE)1090-0268(1999)3:3(143)10.1061/(ASCE)1090-0268(1999)3:3(143) ↗
95. Reliability analysis for eccentrically loaded columns
96. 10.1007/s11029-006-0022-710.1007/s11029-006-0022-7 ↗
97. 10.1007/s11029-008-9012-210.1007/s11029-008-9012-2 ↗
98. 10.1016/j.conbuildmat.2006.06.01710.1016/j.conbuildmat.2006.06.017 ↗
99. Stress-strain characteristics of concrete columns externally confined with advanced fiber composite sheets
100. 10.1061/(ASCE)0733-9445(2003)129:8(1122)10.1061/(ASCE)0733-9445(2003)129:8(1122) ↗