journal article·2016-02

In-Plane Bending and Failure Mechanism of Sandwich Beams with GFRP Skins and Soft Polyurethane Foam Core

Hale Mathieson, Amir Fam

Publisher page

Abstract

The out-of-plane bending of sandwich panels has been widely investigated, but studies on their behavior under in-plane loading are quite scarce. In this study, 18 sandwich beam specimens were tested under three- and four-point in-plane-bending. The specimens are composed of low-density polyurethane core and glass fiber-reinforced polymer (GFRP) skins on both sides. The shear span-to-depth (a/h) ratio was varied from 1.33 to 4.67. Two different skin thicknesses were also used, providing beam depth-to-skin thickness (h/t) ratios of 47 and 94. It was found that the ultimate moment reduced by approximately one third as the a/h ratio increased from 1.33 to 4.67 in sandwich beams with an h/t ratio of 94 and decreased by about one quarter in beams with an h/t ratio of 47. Doubling the skin thickness [i.e., from h/t of 94–47] increased the moment capacity significantly. The percentage increase ranged from 55 to 95% as a/h increased from 1.33 to 4.67. Failure of sandwich beams occurred by skin wrinkling in compression, mostly symmetrically, where skins move in opposite directions. A simplified analytical model accounting for shear and flexural rigidities of the sandwich beam and a skin wrinkling failure criterion in compression was developed and validated against experimental results.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Cellular and Composite Structures · Composite Structure Analysis and Optimization · Structural Analysis and Optimization

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Ph.D. Candidate, Dept. of Civil Engineering, Queen’s Univ., Kingston, ON, Canada K7L 3N6.

Donald and Sarah Munro Chair Professor in Engineering and Applied Science, Dept. of Civil Engineering, Queen’s Univ., Kingston, ON, Canada K7L 3N6 (corresponding author).

References (17)

Show source-provided references
1. Allen H. G. (1969). “Analysis and design of structural sandwich panels.” Pergamon Press Oxford London.10.1016/B978-0-08-012870-2.50006-7 ↗
2. 10.1520/JTE11531J10.1520/JTE11531J ↗
3. 10.1007/s00033-006-6036-010.1007/s00033-006-6036-0 ↗
4. 10.1016/0263-8231(93)90044-B10.1016/0263-8231(93)90044-B ↗
5. 10.1016/j.compstruct.2010.05.00410.1016/j.compstruct.2010.05.004 ↗
6. 10.1016/S0020-7683(97)00078-410.1016/S0020-7683(97)00078-4 ↗
7. 10.2514/3.1042310.2514/3.10423 ↗
8. 10.1016/j.compstruct.2009.09.04610.1016/j.compstruct.2009.09.046 ↗
9. Static and fatigue behavior of sandwich panels with GFRP skins and governed by soft core shear failure
10. 10.1061/(ASCE)CC.1943-5614.000049410.1061/(ASCE)CC.1943-5614.0000494 ↗
11. 10.1061/(ASCE)1090-0268(2004)8:2(141)10.1061/(ASCE)1090-0268(2004)8:2(141) ↗
12. 10.1016/j.compstruct.2006.08.01610.1016/j.compstruct.2006.08.016 ↗
13. 10.1016/S1359-8368(02)00017-310.1016/S1359-8368(02)00017-3 ↗
14. 10.1061/(ASCE)CC.1943-5614.000017610.1061/(ASCE)CC.1943-5614.0000176 ↗
15. 10.1177/073168441244549410.1177/0731684412445494 ↗
16. 10.1177/002199831036957710.1177/0021998310369577 ↗
17. 10.1177/002199830708796510.1177/0021998307087965 ↗