Design Proposal to Avoid Peeling Failure in FRP-Strengthened Reinforced Concrete Beams
Source abstract
Abstract
According to the available experimental work, the most common failure in existing structures strengthened by plate bonding is the laminate peeling off. In the last few years, an important effort in the development of mathematical models to avoid premature peeling failures has been made. However, a suitable and reliable design method to predict debonding due to the shear flow between crack discontinuities or at the laminate end is still not available. This paper describes a new design procedure for structures strengthened by plate bonding to avoid peeling failure at any location. After calculating the laminate area required for flexural strengthening, a two-step procedure to prevent peeling failure is proposed. The first step, to avoid peeling failure along the span, is based on a shear-bending interaction diagram associated with the theoretical maximum transferred force between laminate and support along the crack spacing before laminate debonding. This interaction diagram can be obtained through the application of nonlinear fracture mechanics. The second step consists of checking for peeling failure at the laminate end. The bonded length between the laminate end and the nearest crack should be enough to transfer the laminate tensile force acting on this crack. The proposed method has been verified with available experimental results assembled in a database. A good agreement between the experimental and predicted failure load has been obtained. Finally, an application example is presented to show the applicability of the method.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Structural Behavior of Reinforced Concrete · Concrete Corrosion and Durability · Structural Load-Bearing Analysis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Assistant Professor, Dept. of Construction Engineering, Civil Engineering School, Technical Univ. of Catalonia, Jordi Girona 1-3, C-1 201, 08034 Barcelona, Spain (corresponding author).
Engineer, Tec-Cuatro, S.A., Amigó 15, 1ª Planta, 08021 Barcelona, Spain.
Professor, Dept. of Construction Engineering, Civil Engineering School, Technical Univ. of Catalonia, Jordi Girona 1-3, C-1 201, 08034 Barcelona, Spain.
References (20)
Show source-provided references
1. 10.1061/(ASCE)0733-9445(2001)127:12(1453)10.1061/(ASCE)0733-9445(2001)127:12(1453) ↗
2. American Concrete Institute (ACI). (2002). “Guide for the design and construction of externally bonded FRP systems for strengthening concrete structures.” ACI 440 Detroit.
3. Brosens K. (2001). “Anchorage of externally bonded steel plates and CFRP laminates for the strengthening of concrete elements.” Ph.D. thesis Katholieke Universiteit Leuven Belgium.
4. Brosens K. and Van Gemert D. (1998). “Plate end shear design for external CFRP laminates.” Proc. FRAMCOS-3 Aedificatio Publishers Freiburg 1793–1804.
5. 10.1061/(ASCE)0733-9445(2001)127:7(784)10.1061/(ASCE)0733-9445(2001)127:7(784) ↗
6. Collins M. P. (2001). “Evaluation of shear design procedures for concrete structures.” Rep. Prepared for the CSA Technical Committee on Reinforced Concrete Design Canada.
7. 10.1061/(ASCE)0733-9445(2001)127:4(367)10.1061/(ASCE)0733-9445(2001)127:4(367) ↗
8. European Committee for Standardization. (1992). “Design of concrete structures. Part 1–1: General rules and rules for building.” Eurocode 2 .
9. fib bulletin 14 . (2001). “Externally bonded FRP reinforcement for RC structures.” Technical Rep. Prepared for Task Group 9.3 FRP Reinforcement for Concrete Structures FIB International Federation for Structural Concrete Laussane Switzerland.
10. 10.1061/(ASCE)1090-0268(2007)11:2(161)10.1061/(ASCE)1090-0268(2007)11:2(161) ↗
11. Neubauer U. (2000). “Verbundtragverhalten geklebter Lamellen aus Kohlenstoffaser-Verbundwerkstoff zur Verstärkung von Betonbauteilen.” Ph.D. thesis TU Braunschweig Germany.
12. Niedermeier R. (2000). “Envelope line of tensile forces while using externally bonded reinforcement.” Ph.D. thesis TU Münich Munchen.
13. Oller E. (2005). “Peeling failure in beams strengthened by plate bonding. A design proposal.” Ph.D. thesis Technical University of Catalonia Spain.
14. 10.1061/(ASCE)1090-0268(2009)13:1(35)10.1061/(ASCE)1090-0268(2009)13:1(35) ↗
15. 10.1680/istbu.1997.2983610.1680/istbu.1997.29836 ↗
16. 10.1061/(ASCE)1090-0268(2008)12:3(284)10.1061/(ASCE)1090-0268(2008)12:3(284) ↗
17. Täljsten B. (1994). “Plate bonding. strengthening of existing concrete structures with epoxy bonded plates of steel or fibre reinforced plastics.” Ph.D. thesis Lule University of Technology Sweden.
18. 10.1016/S0950-0618(03)00043-610.1016/S0950-0618(03)00043-6 ↗
19. Vasseur L.Matthys S.Taerwe L. and (2008). “Bond behaviour of externally bonded FRP to concrete in the case of 3-point bending tests.” Proc. Challenges of Civil Construction T. Marques eds. FEUP Porto Portugal 164–165.
20. Study on debonding failure load of RC beams strengthened with FRP sheets