journal article·2023-02

A Strut-and-Tie Model for Predicting the Shear Strength of Exterior Beam–Column Joints Strengthened with Fiber-Reinforced Polymers

Reza Mashhadi, Mohammad Ali Dastan Diznab, Fariborz M. Tehrani

Publisher page

Abstract

This paper presents a new strut-and-tie model (STM) based on provisions of ACI 318-19 and ACI 440.2R-17 for estimating the shear strength of fiber-reinforced polymer (FRP)-strengthened exterior joints. Beam–column joints are vulnerable elements in reinforced-concrete structures subjected to seismic loadings and similar extreme demands. The FRP strengthening technique offers numerous advantages for retrofitting joints in existing structures with inadequate reinforcement or confinement. The design of FRP-strengthened joints requires the development of reliable procedures, including equations to predict the shear strength of the joint. Existing literature and research on STM warrant the development of simple, reliable, and practical specifications applied to a wide range of design criteria. The proposed method involves an STM model containing horizontal and vertical mechanisms. The methodology compares predicted joint shear strength results with existing experimental results to obtain a reliable design approach. This comparison, along with verification of alternative analytical results, indicates the appropriateness of the presented model for predicting the shear strength of FRP-strengthened joints. Results contribute to the enhancement and efficiency of the practical design of these joints.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Structural Behavior of Reinforced Concrete · Concrete Corrosion and Durability · Structural Load-Bearing Analysis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Faculty of Engineering, Dept. of Civil Engineering, Arak Univ., Karbala Blvd., Arak 38481-77584, Iran. ORCID: .

Faculty of Engineering, Dept. of Civil Engineering, Arak Univ., Karbala Blvd., Arak 38481-77584, Iran (corresponding author). ORCID: .

Lyles College of Engineering, Dept. of Civil and Geomatics Engineering, California State Univ., Fresno, 2320 E. San Ramon Ave., Fresno, CA 93740-8030. ORCID: .

References (64)

Show source-provided references
1. ACI (American Concrete Institute). 2017. Guide for the design and construction of externally bonded FRP systems for strengthening concrete structures. ACI 440.2 R-17. Farmington Hills, MI: ACI.
2. ACI (American Concrete Institute). 2019. Building code requirements for structural concrete. ACI 318R-19. Farmington Hills, MI: ACI.
3. Akguzel, U., and S. Pampanin. 2012. “Assessment and design procedure for the seismic retrofit of reinforced concrete beam–column joints using FRP composite materials.” J. Compos. Constr. 16 (1): 21–34. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000242.10.1061/(ASCE)CC.1943-5614.0000242 ↗
4. Al-Salloum, Y. A., and T. H. Almusallam. 2007. “Seismic response of interior RC beam–column joints upgraded with FRP sheets. I: Experimental study.” J. Compos. Constr. 11 (6): 575–589. https://doi.org/10.1061/(ASCE)1090-0268(2007)11:6(575).10.1061/(ASCE)1090-0268(2007)11:6(575) ↗
5. Alsayed, S. H., Y. A. Al-Salloum, T. H. Almusallam, and N. A. Siddiqui. 2010. “Seismic response of FRP-upgraded exterior RC beam–column joints.” J. Compos. Constr. 14 (2): 195–208. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000067.10.1061/(ASCE)CC.1943-5614.0000067 ↗
6. Antonopoulos, C. P., and T. C. Triantafillou. 2002. “Analysis of FRP-strengthened RC beam–column joints.” J. Compos. Constr. 6 (1): 41–51. https://doi.org/10.1061/(ASCE)1090-0268(2002)6:1(41).10.1061/(ASCE)1090-0268(2002)6:1(41) ↗
7. Antonopoulos, C. P., and T. C. Triantafillou. 2003. “Experimental investigation of FRP-strengthened RC beam–column joints.” J. Compos. Constr. 7 (1): 39–49. https://doi.org/10.1061/(ASCE)1090-0268(2003)7:1(39).10.1061/(ASCE)1090-0268(2003)7:1(39) ↗
8. Attari, N., Y. S. Youcef, and S. Amziane. 2019. “Seismic performance of reinforced concrete beam–column joint strengthening by FRP sheets.” Structures 20: 353–364. https://doi.org/10.1016/j.istruc.2019.04.007.10.1016/j.istruc.2019.04.007 ↗
9. Bakir, P. G., and H. M. Boduroglu. 2006. “Nonlinear analysis of beam–column joints using softened truss model.” Mech. Res. Commun. 33 (2): 134–147. https://doi.org/10.1016/j.mechrescom.2005.09.002.10.1016/j.mechrescom.2005.09.002 ↗
10. Bousselham, A. 2010. “State of research on seismic retrofit of RC beam–column joints with externally bonded FRP.” J. Compos. Constr. 14 (1): 49–61. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000049.10.1061/(ASCE)CC.1943-5614.0000049 ↗
11. D’Ayala, D., A. Penford, and S. Valentini. 2003. “Use of FRP fabric for strengthening of reinforced concrete beam–column joints.” In Proc., 10th Int. Conf. on Structural Faults and Repair. Edinburgh, Scotland: Engineering Technics Press.
12. Del Vecchio, C., M. Di Ludovico, A. Balsamo, A. Prota, G. Manfredi, and M. Dolce. 2014. “Experimental investigation of exterior RC beam–column joints retrofitted with FRP systems.” J. Compos. Constr. 18 (4): 04014002. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000459.10.1061/(ASCE)CC.1943-5614.0000459 ↗
13. Del Vecchio, C., M. Di Ludovico, A. Prota, and G. Manfredi. 2015. “Analytical model and design approach for FRP strengthening of non-conforming RC corner beam–column joints.” Eng. Struct. 87: 8–20. https://doi.org/10.1016/j.engstruct.2015.01.013.10.1016/j.engstruct.2015.01.013 ↗
14. Dhahir, M. K. 2018. “Strut and tie modeling of deep beams shear strengthened with FRP laminates.” Compos. Struct. 193: 247–259. https://doi.org/10.1016/j.compstruct.2018.03.073.10.1016/j.compstruct.2018.03.073 ↗
15. El-Amoury, T., and A. Ghobarah. 2002. “Seismic rehabilitation of beam–column joint using GFRP sheets.” Eng. Struct. 24 (11): 1397–1407. https://doi.org/10.1016/S0141-0296(02)00081-0.10.1016/S0141-0296(02)00081-0 ↗
16. El-Metwally, S., and W.-F. Chen. 2018. Structural concrete: Strut-and-tie models for unified design. Boca Raton, FL: CRC Press.
17. Engindeniz, M., L. Kahn, and A. Zureick. 2008. “Performance of an RC corner beam–column joint severely damaged under bidirectional loading and rehabilitated with FRP composites.” In Seismic Strengthening of Concrete Buildings Using FRP Composites. Farmington Hills, MI: American Concrete Institute.
18. Farghaly, A. S., and B. Benmokrane. 2013. “Shear behavior of FRP-reinforced concrete deep beams without web reinforcement.” J. Compos. Constr. 17 (6): 04013015. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000385.10.1061/(ASCE)CC.1943-5614.0000385 ↗
19. Garcia, R., Y. Jemaa, Y. Helal, M. Guadagnini, and K. Pilakoutas. 2014. “Seismic strengthening of severely damaged beam–column RC joints using CFRP.” J. Compos. Constr. 18 (2): 04013048. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000448.10.1061/(ASCE)CC.1943-5614.0000448 ↗
20. Geng, Z.-J., M. J. Chajes, T.-W. Chou, and D. Y.-C. Pan. 1998. “The retrofitting of reinforced concrete column-to-beam connections.” Compos. Sci. Technol. 58 (8): 1297–1305. https://doi.org/10.1016/S0266-3538(98)00014-1.10.1016/S0266-3538(98)00014-1 ↗
21. Gergely, J., C. P. Pantelides, and L. D. Reaveley. 2000. “Shear strengthening of RCT-joints using CFRP composites.” J. Compos. Constr. 4 (2): 56–64. https://doi.org/10.1061/(ASCE)1090-0268(2000)4:2(56).10.1061/(ASCE)1090-0268(2000)4:2(56) ↗
22. Ghobarah, A., and T. El-Amoury. 2005. “Seismic rehabilitation of deficient exterior concrete frame joints.” J. Compos. Constr. 9 (5): 408–416. https://doi.org/10.1061/(ASCE)1090-0268(2005)9:5(408).10.1061/(ASCE)1090-0268(2005)9:5(408) ↗
23. Ghobarah, A., and A. Said. 2002. “Shear strengthening of beam–column joints.” Eng. Struct. 24 (7): 881–888. https://doi.org/10.1016/S0141-0296(02)00026-3.10.1016/S0141-0296(02)00026-3 ↗
24. Godat, A., and O. Chaallal. 2013. “Strut-and-tie method for externally bonded FRP shear-strengthened large-scale RC beams.” Compos. Struct. 99: 327–338. https://doi.org/10.1016/j.compstruct.2012.11.034.10.1016/j.compstruct.2012.11.034 ↗
25. Hanoon, A. N., M. S. Jaafar, S. R. Al Zaidee, F. Hejazi, and F. N. A. A. Aziz. 2017a. “Effectiveness factor of the strut-and-tie model for reinforced concrete deep beams strengthened with CFRP sheet.” J. Build. Eng. 12: 8–16. https://doi.org/10.1016/j.jobe.2017.05.001.10.1016/j.jobe.2017.05.001 ↗
26. Hanoon, A. N., M. S. Jaafar, F. Hejazi, and F. N. A. A. Aziz. 2017b. “Strut-and-tie model for externally bonded CFRP-strengthened reinforced concrete deep beams based on particle swarm optimization algorithm: CFRP debonding and rupture.” Constr. Build. Mater. 147: 428–447. https://doi.org/10.1016/j.conbuildmat.2017.04.094.10.1016/j.conbuildmat.2017.04.094 ↗
27. Hasan, Q. F., H. Tekeli, and F. Demir. 2016. “NSM rebar and CFRP laminate strengthening for RC columns subjected to cyclic loading.” Constr. Build. Mater. 119: 21–30. https://doi.org/10.1016/j.conbuildmat.2016.04.120.10.1016/j.conbuildmat.2016.04.120 ↗
28. Hejabi, H., and M. Z. Kabir. 2015. “Analytical model for predicting shear strengths of FRP-retrofitted exterior reinforced concrete beam–column joints.” Sci. Iran. 22 (4): 1363–1372.
29. Hwang, S.-J., and H.-J. Lee. 1999. “Analytical model for predicting shear strengths of exterior reinforced concrete beam–column joints for seismic resistance.” Struct. J. 96 (5): 846–858.
30. Kalogeropoulos, G. I., A.-D. G. Tsonos, D. Konstandinidis, and S. Tsetines. 2016. “Pre-earthquake and post-earthquake retrofitting of poorly detailed exterior RC beam-to–column joints.” Eng. Struct. 109: 1–15. https://doi.org/10.1016/j.engstruct.2015.11.009.10.1016/j.engstruct.2015.11.009 ↗
31. Karayannis, C. G., and G. M. Sirkelis. 2008. “Strengthening and rehabilitation of RC beam–column joints using carbon-FRP jacketing and epoxy resin injection.” Earthquake Eng. Struct. Dyn. 37 (5): 769–790. https://doi.org/10.1002/eqe.785.10.1002/eqe.785 ↗
32. Kassem, W. 2016. “Strut-and-tie modelling for the analysis and design of RC beam–column joints.” Mater. Struct. 49 (8): 3459–3476. https://doi.org/10.1617/s11527-015-0732-1.10.1617/s11527-015-0732-1 ↗
33. Kim, D.-J., J. Lee, and Y. H. Lee. 2014. “Effectiveness factor of strut-and-tie model for concrete deep beams reinforced with FRP rebars.” Composites, Part B 56: 117–125. https://doi.org/10.1016/j.compositesb.2013.08.009.10.1016/j.compositesb.2013.08.009 ↗
34. Lee, W.T., Y.J. Chiou, and M. Shih. 2010. “Reinforced concrete beam–column joint strengthened with carbon fiber reinforced polymer.” Compos. Struct. 92 (1): 48–60. https://doi.org/10.1016/j.compstruct.2009.06.011.10.1016/j.compstruct.2009.06.011 ↗
35. Le-Trung, K., K. Lee, J. Lee, D. H. Lee, and S. Woo. 2010. “Experimental study of RC beam–column joints strengthened using CFRP composites.” Composites, Part B 41 (1): 76–85. https://doi.org/10.1016/j.compositesb.2009.06.005.10.1016/j.compositesb.2009.06.005 ↗
36. Li, B., K. Qian, and C. T. N. Tran. 2013. “Retrofitting earthquake-damaged RC structural walls with openings by externally bonded FRP strips and sheets.” J. Compos. Constr. 17 (2): 259–270. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000336.10.1061/(ASCE)CC.1943-5614.0000336 ↗
37. Mashhadi, R., M. A. Dastan Diznab, and F. M. Tehrani. 2022. “Strut-and-tie model for predicting the shear strength of exterior beam–column joints without transverse reinforcement.” J. Struct. Eng. 148 (2): 04021256. https://doi.org/10.1061/(ASCE)ST.1943-541X.0003223.10.1061/(ASCE)ST.1943-541X.0003223 ↗
38. MATLAB. 2020. MATLAB. Natick, MA: The MathWorks Inc.
39. Mosallam, A. S. 2000. “Strength and ductility of reinforced concrete moment frame connections strengthened with quasi-isotropic laminates.” Composites, Part B 31 (6–7): 481–497. https://doi.org/10.1016/S1359-8368(99)00068-2.10.1016/S1359-8368(99)00068-2 ↗
40. Mosallam, A., K. Allam, and M. Salama. 2019. “Analytical and numerical modeling of RC beam–column joints retrofitted with FRP laminates and hybrid composite connectors.” Compos. Struct. 214: 486–503. https://doi.org/10.1016/j.compstruct.2019.02.032.10.1016/j.compstruct.2019.02.032 ↗
41. Mukherjee, A., and M. Joshi. 2005. “FRPC reinforced concrete beam–column joints under cyclic excitation.” Compos. Struct. 70 (2): 185–199. https://doi.org/10.1016/j.compstruct.2004.08.022.10.1016/j.compstruct.2004.08.022 ↗
42. Nehdi, M., Z. Omeman, and H. El-Chabib. 2008. “Optimal efficiency factor in strut-and-tie model for FRP-reinforced concrete short beams with (1.5< a/d< 2.5).” Mater. Struct. 41 (10): 1713–1727. https://doi.org/10.1617/s11527-008-9359-9.10.1617/s11527-008-9359-9 ↗
43. Okahashi, Y., and C. P. Pantelides. 2017. “Strut-and-tie model for interior RC beam–column joints with substandard details retrofitted with CFRP jackets.” Compos. Struct. 165 (Suppl. C): 1–8. https://doi.org/10.1016/j.compstruct.2017.01.004.10.1016/j.compstruct.2017.01.004 ↗
44. Pantelides, C. P., C. Clyde, and L. D. Reaveley. 2000. “Rehabilitation of R/C building joints with FRP composites.” In Proc., 12th World Conf. on Earthquake Engineering. Willington, New Zealand: New Zealand Society for Earthquake Engineering.
45. Pantelides, C. P., Y. Okahashi, and L. Reaveley. 2008. “Seismic rehabilitation of reinforced concrete frame interior beam–column joints with FRP composites.” J. Compos. Constr. 12 (4): 435–445. https://doi.org/10.1061/(ASCE)1090-0268(2008)12:4(435).10.1061/(ASCE)1090-0268(2008)12:4(435) ↗
46. Park, S., and R. S. Aboutaha. 2009. “Strut-and-tie method for CFRP strengthened deep RC members.” J. Struct. Eng. 135 (6): 632–643. https://doi.org/10.1061/(ASCE)0733-9445(2009)135:6(632).10.1061/(ASCE)0733-9445(2009)135:6(632) ↗
47. Parvin, A., S. Altay, C. Yalcin, and O. Kaya. 2010. “CFRP rehabilitation of concrete frame joints with inadequate shear and anchorage details.” J. Compos. Constr. 14 (1): 72–82. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000055.10.1061/(ASCE)CC.1943-5614.0000055 ↗
48. Paulay, T., and M. N. Priestley. 1992. Seismic design of reinforced concrete and masonry buildings. Chichester, UK: Wiley.10.1002/9780470172841 ↗
49. Perera, R., J. Vique, A. Arteaga, and A. D. Diego. 2009. “Shear capacity of reinforced concrete members strengthened in shear with FRP by using strut-and-tie models and genetic algorithms.” Composites, Part B 40 (8): 714–726. https://doi.org/10.1016/j.compositesb.2009.06.008.10.1016/j.compositesb.2009.06.008 ↗
50. Pohoryles, D. A., J. Melo, T. Rossetto, H. Varum, and L. Bisby. 2019. “Seismic retrofit schemes with FRP for deficient RC beam–column joints: State-of-the-art review.” J. Compos. Constr. 23 (4): 03119001. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000950.10.1061/(ASCE)CC.1943-5614.0000950 ↗
51. Priestley, M. 1997. “Displacement-based seismic assessment of reinforced concrete buildings.” J. Earthquake Eng. 1 (1): 157–192.10.1080/13632469708962365 ↗
52. Prota, A., A. Nanni, G. Manfredi, and E. Cosenza. 2004. “Selective upgrade of underdesigned reinforced concrete beam–column joints using carbon fiber-reinforced polymers.” Struct. J. 101 (5): 699–707.
53. Qazi, S., L. Michel, E. Ferrier, and A. Limam. 2015. “Strut-and-tie model for a reinforced concrete wall strengthened with carbon fibre-reinforced polymers.” Compos. Struct. 128 (Suppl. C): 87–99. https://doi.org/10.1016/j.compstruct.2015.03.024.10.1016/j.compstruct.2015.03.024 ↗
54. Realfonzo, R., A. Napoli, and J. G. R. Pinilla. 2014. “Cyclic behavior of RC beam–column joints strengthened with FRP systems.” Constr. Build. Mater. 54: 282–297. https://doi.org/10.1016/j.conbuildmat.2013.12.043.10.1016/j.conbuildmat.2013.12.043 ↗
55. Saenz, N., and C. P. Pantelides. 2005. “Shear friction capacity of concrete with external carbon FRP strips.” J. Struct. Eng. 131 (2): 1911–1919. https://doi.org/10.1061/(ASCE)0733-9445(2005)131:12(1911).10.1061/(ASCE)0733-9445(2005)131:12(1911) ↗
56. Saenz, N., C. P. Pantelides, and L. D. Reaveley. 2004. “Strut-and-tie model for shear friction of concrete with fiber-reinforced polymer composites.” ACI Struct. J. 101 (6): 863–871.
57. Shadravan, B., and F. M. Tehrani. 2017. “A review of direct shear testing configurations for bond between fiber-reinforced polymer sheets on concrete and masonry substrates.” Period. Polytech. Civ. Eng. 61 (4): 740–751.
58. Shiohara, H., F. Kusuhara, S. Tajiri, and H. Fukuyama. 2010. “Seismic retrofit of reinforced concrete beam–column joints with CFRP composites.” In Improving the Seismic Performance of Existing Buildings and Other Structures, 1449–1459. Reston, VA: ASCE.
59. Shrestha, R., S. T. Smith, and B. Samali. 2009. “Strengthening RC beam–column connections with FRP strips.” Proc. Inst. Civ. Eng. Struct. Build. 162 (5): 323–334. https://doi.org/10.1680/stbu.2009.162.5.323.10.1680/stbu.2009.162.5.323 ↗
60. Tehrani, F. M. 2008. Performance of steel fiber-reinforced concrete in beam–column connections. Los Angeles: Univ. of California.
61. Tsonos, A. G. 2008. “Effectiveness of CFRP-jackets and RC-jackets in post-earthquake and pre-earthquake retrofitting of beam–column subassemblages.” Eng. Struct. 30 (3): 777–793. https://doi.org/10.1016/j.engstruct.2007.05.008.10.1016/j.engstruct.2007.05.008 ↗
62. Wong, H. F., and J. S. Kuang. 2014. “Predicting shear strength of RC interior beam–column joints by modified rotating-angle softened-truss model.” Comput. Struct. 133 (Suppl. C): 12–17. https://doi.org/10.1016/j.compstruc.2013.11.008.10.1016/j.compstruc.2013.11.008 ↗
63. Yu, J., X. Shang, and Z. Lu. 2016. “Efficiency of externally bonded L-shaped FRP laminates in strengthening reinforced-concrete interior beam–column joints.” J. Compos. Constr. 20 (3): 04015064. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000622.10.1061/(ASCE)CC.1943-5614.0000622 ↗
64. Zerkane, A. S., Y. M. Saeed, and F. N. Rad. 2019. “Cyclic loading behavior of CFRP-wrapped non-ductile beam–column joints.” Spec. Publ. 331: 34–54.