journal article·2026-06Open access

Advances in foam extrusion of micro- and nanocellular polymers: Strategies for controlling cell size and open-cell content

Marcos Merillas, Miguel Ángel Rodríguez-Pérez, Judith Martín-de León, Victoria Bernardo

Abstract

Extrusion foaming is a key industrial technology for the production of lightweight polymer foams widely used in many markets. Recently, growing interest has focused on micro- and nanocellular polymer foams due to their outstanding combination of properties. To date, the fabrication of such materials has been restricted to laboratory-scale processes. Among foaming technologies, foam extrusion stands out as the most promising route for scaling up the production of micro- and nanocellular polymers. However, achieving fine cellular structures while maintaining low density and process stability remains a major challenge due to the intrinsic characteristics of the extrusion process. Therefore, extending extrusion foaming towards micro- and nanoscale structures requires a deep understanding of the underlying physical mechanisms to design production process able to achieve such structures. This review provides a comprehensive overview of the strategies reported in the literature to control cellular architecture in extrusion foaming, particularly the cell size and cell interconnectivity. First, the fundamental principles of extrusion foaming are summarized. Then, approaches for cell size reduction are discussed, including blowing agent selection, processing conditions, and the use of nucleating agents, ranging from conventional mineral fillers to nanoscale and self-assembling additives. Special attention is given to mechanisms governing cell nucleation, growth, coalescence, and stabilization, highlighting the trade-offs between cell refinement and foam density. In addition, strategies aimed at promoting controlled open-cell structures are reviewed, given their growing relevance for some advanced applications. The effects of melt strength modification and the introduction of heterogeneities are examined. Finally, a critical outlook on current limitations and the underlying causes of process and material constraints is discussed. Open challenges and future research directions are also presented. Overall, this review provides a unified framework linking formulation, processing, and cellular structure in extrusion foaming. By identifying the key factors governing cell size reduction and open-cell formation, it aims to guide future design of formulations and processes for the manufacturing of high-performance polymer foams with controlled micro- and nanocellular open-cell structures.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Polymer Foaming and Composites · Advanced Cellulose Research Studies · Pickering emulsions and particle stabilization

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (100+)

Show source-provided references
2. Eaves · 2004
3. A process for making microcellular thermoplastic parts10.1002/pen.760302010 ↗
4. Micro and nano cellular amorphous polymers (PMMA, PS) in supercritical CO2 assisted by nanostructured CO2-philic block copolymers - One step foaming process10.1016/j.supflu.2011.04.022 ↗
5. A model to predict the cell density and cell size distribution in nano-cellular foams10.1016/j.ces.2015.08.029 ↗
6. Effects of graphene nanoplatelets on the morphology of polycarbonate-graphene composite foams prepared by supercritical carbon dioxide two-step foaming10.1016/j.supflu.2015.02.005 ↗
7. Past and present developments in polymer bead foams and bead foaming technology10.1016/j.polymer.2014.10.078 ↗
8. Xu · 2010
9. Microcellular injection molding of polymers: a review of process know-how, emerging technologies, and future directions10.1016/j.coche.2021.100694 ↗
10. Extruded Polystyrene Market Size & Share Analysis - Growth Trends & Forecasts (2025 - 2030) Source: https://www.mordorintelligence.com/industry-reports/extruded-polystyrene-market, (n.d.). 〈https://www.mordorintelligence.com/industry-reports/extruded-polystyrene-market〉.
11. The production and analysis of microcellular foam
12. RodrÍguez PÉrez · 2023
13. Mechanism of strength improvement of foamed plastics having fine cell10.1177/0021955X06075585 ↗
14. Fracture toughness of high density polycarbonate microcellular foams10.1177/0021955X06063512 ↗
15. Experimental characterization of the tensile behavior of microcellular polycarbonate foams10.1115/1.2904310 ↗
16. A prediction model using response surface methodology based on cell size and foam density to predict thermal conductivity of polystyrene foams10.1007/s00231-019-02628-8 ↗
17. Nanoporous polymeric materials: a new class of materials with enhanced properties10.1016/j.pmatsci.2016.02.002 ↗
18. Experimental validation of the Knudsen effect in nanocellular polymeric foams10.1016/j.polymer.2014.10.006 ↗
19. Ultra-tough and super thermal-insulation nanocellular PMMA/TPU10.1016/j.cej.2017.05.116 ↗
20. Transparent nanocellular PMMA: characterization and modeling of the optical properties10.1016/j.polymer.2019.03.010 ↗
21. Towards a new generation of polymeric foams: PMMA nanocellular foams with enhanced physical properties10.1016/j.polymer.2015.03.003 ↗
22. CO 2 ‐blown nanocellular foams10.1002/app.41293 ↗
23. Ordered nanoporous polymers from polystyrene-polylactide block copolymers10.1021/ja0278584 ↗
24. Nanoporous melamine - Formaldehyde gels by microemulsion templating10.1021/cm8015319 ↗
25. Key production parameters to obtain transparent nanocellular PMMA10.1002/mame.201700343 ↗
26. Nanocellular polymer foams nucleated by core-shell nanoparticles10.1016/j.polymer.2016.09.016 ↗
27. Drug delivery properties of macroporous polystyrene solid foams10.18433/J3X884 ↗
28. Opening pores and extending the application window: open-cell nanocellular foams10.1002/mame.202300087 ↗
29. Thermal conductivity analysis of a new sub-micron sized polystyrene foam10.1177/0021955X20943101 ↗
30. G. Munters, J. Tandberg, 2,023,204 U.S. Patent, 2023204, 1935.
31. Lee · 2000
32. Half a century of polystyrene-a survey of the chemistry and physics of a pioneering material10.1002/anie.198103441 ↗
33. F.L. Johnson, 2,256,483 U.S. Patent, 2256483, 1941.
34. R.G. Parrish, 3,637,458 U.S. Patent, 3637458, 1972.
35. K. Cink, J.C. Smith, J.F. Nangeroni, J.R. Randall, 8,013,031 B2 U.S. Patent, 8013031, 2011.
36. Extruded Polystyrene Market Research Report Information By Application (foundation, wall, roof, ceiling, floor, and others), by End-Use (Residential Construction and Commercial Construction), And By Region (North America, Europe, Asia-Pacific, And Rest Of, (n.d.). 〈https://www.marketresearchfuture.com/reports/extruded-polystyrene-market-7500〉.
37. Polyethylene Foam Market Size & Share Analysis - Growth Trends & Forecasts (2025 - 2030) Source: https://www.mordorintelligence.com/industry-reports/polyethylene-foam-market, (n.d.). 〈https://www.mordorintelligence.com/industry-reports/polyethylene-foam-market〉.
38. Modified polyethylene foam for critical environments10.3390/polym14214688 ↗
39. Extruded Polypropylene (XPP) Foam Market Size & Share Analysis - Growth Trends & Forecasts (2025 - 2030) Source: https://www.mordorintelligence.com/industry-reports/extruded-polypropylene-xpp-foam-market, (n.d.). 〈https://www.mordorintelligence.com/industry-reports/extruded-polypropylene-xpp-foam-market〉.
40. M. Xanthos, Recycling of the #5 Polymer, Science (80–.). 337 (2012) 700–702. https://doi.org/10.1126/science.1221806.10.1126/science.1221806 ↗
41. Mechanical recycling and performance characterisation of insert-injection moulded homo-polypropylene single-polymer composites and foams10.1016/j.coco.2024.102176 ↗
42. Pilla · 2011
43. C. Vannini, F. Fiordelisi, W. Movilli, F. Lanzani, Polylactic acid-based degradable foams and process for their production, EP 1528079 A1, 2005.
44. H. Zhang, Scale-Up of Extrusion Foaming Process for Manufacture of Polystyrene Foams Using Carbon Dioxide, University of Toronto, 2010.
45. Extruded open-celled LDPE-based foams using non-homogeneous melt structure10.1515/POLYENG.2005.25.3.239 ↗
46. Mechanical anisotropy of PS/CO2 microcellular foam sheet prepared by foaming extrusion10.1177/0021955X16670586 ↗
47. Rheology of molten polystyrene with dissolved supercritical and near-critical gases10.1002/(SICI)1099-0488(19991001)37:19<2771::AID-POLB6>3.0.CO;2-9 ↗
48. New challenges in polymer foaming: a review of extrusion processes assisted by supercritical carbon dioxide10.1016/j.progpolymsci.2010.12.004 ↗
49. Effects of high-pressure CO2 on the glass transition temperature and mechanical properties of polystyrene10.1002/pol.1982.180200804 ↗
50. CO2-assisted melting of semicrystalline polymers10.1021/ma9712211 ↗
51. Effect of polymer swell in extrusion foaming of low-density polyethylene10.1063/5.0035033 ↗
52. Solubility of polymers and copolymers in supercritical CO 210.1021/jp9615823 ↗
53. Solubility of butane and isobutane in molten polypropylene and polystyrene10.1002/pen.20213 ↗
54. Solubilities of carbon dioxide and nitrogen in polystyrene under high temperature and pressure10.1016/S0378-3812(96)03094-4 ↗
55. Solubilities and diffusion coefficients of carbon dioxide in poly(vinyl acetate) and polystyrene10.1016/S0896-8446(00)00092-9 ↗
56. Bernardo · 2019
57. Lee · 1985
58. A new promising nucleating agent for polymer foaming: effects of hollow molecular-sieve particles on polypropylene supercritical CO2 microcellular foaming10.1039/C8RA03071E ↗
59. Polymer nanocomposite foams10.1039/c2ta00086e ↗
60. Low-density PMMA/MAM nanocellular polymers using low MAM contents: Production and characterization10.1016/j.polymer.2018.12.057 ↗
61. Understanding the role of MAM molecular weight in the production of PMMA/MAM nanocellular polymers10.1016/j.polymer.2018.08.022 ↗
62. E. Laguna-Gutierrez, Understanding the Foamability of Complex Polymeric Systems By Using Extensional Rheology, 2016.
63. Mechanism of permeability modification in polyethylene foams10.1177/0021955X07081649 ↗
64. J.B. Burkholder, O. Hodnebrog, B.C. McDonald, V. Orkin, V.C. Papadimitriou, D. Van Hoomissen, Ozone 2022 Assesment. Annex: Summary of Abundances, Lifetimes, ODPs, REs, GWPs, GTPs., 2022.
65. An evaluation of the thermal conductivity of extruded polystyrene foam blown with HFC-134a or HCFC-142b10.1177/0021955X04043719 ↗
66. United Nations Environment Programme (UNEP), Montreal Protocol on Substances that Deplete the Ozone Layer., 1987. https://doi.org/10.18356/df488915-en-fr.10.18356/df488915-en-fr ↗
67. Assessment of hydrofluoropropenes as insulating blowing agents for extruded polystyrene foams10.1177/0021955X13488398 ↗
68. Honeywell, SOLSTICE ® GAS BLOWING AGENT: A Low Global Warming Gas Blowing Agent to Improve Thermal Conductivity in XPS Production, 2023.
69. Honeywell, HFO-1234ze(E): Properties and Application to Extruded Polystyrene, n.d.
70. Nucleation of microcellular foam: theory and practice10.1002/pen.760270704 ↗
71. The nucleation of microcellular thermoplastic foam with additives: part II: experimental results and discussion10.1002/pen.760270703 ↗
72. Generation of microcellular polymeric foams using supercritical carbon dioxide. I: effect of pressure and temperature on nucleation10.1002/pen.760341407 ↗
73. Foam extrusion of polystyrene blown with HFC-134a10.1177/026248930202100501 ↗
74. Foaming polystyrene with mixtures of carbon dioxide and HFC-134a10.1177/026248930302200201 ↗
75. An elementary molecular theory of classical fluids. Pure fluids10.1021/j100562a008 ↗
76. An elementary equation of state for polymer liquids10.1002/pol.1977.130150202 ↗
77. Polymeric foaming predictions from the sanchez-lacombe equation of state: application to polypropylene-carbon dioxide mixtures10.1103/PhysRevApplied.8.044009 ↗
78. Solubilities and diffusion coefficients of carbon dioxide and nitrogen in polypropylene, high-density polyethylene, and polystyrene under high pressures and temperatures10.1016/S0378-3812(99)00217-4 ↗
79. Foaming polystyrene with a mixture of CO2 and ethanol10.1177/0021955X06060948 ↗
80. Introducing water as a coblowing agent in the carbon dioxide extrusion foaming process for polystyrene thermal insulation foams10.1002/pen.21624 ↗
81. Extruded polystyrene foams with bimodal cell morphology10.1016/j.polymer.2012.04.006 ↗
82. Bi-cellular foam structure of polystyrene from extrusion foaming process10.1177/0021955X09343632 ↗
83. Open-celled foams from polyethersulfone/poly(ethylene glycol) blends using foam extrusion
84. A study of foam extrusion using a chemical blowing agent10.1002/app.1976.070200615 ↗
85. Basic study of extrusion of polyethylene and polystyrene foams10.1002/app.1979.070230406 ↗
86. Effect of the pressure drop rate on cell nucleation in continuous processing of microcellular polymers10.1002/pen.760350509 ↗
87. Low density microcellular foam processing in extrusion using CO210.1002/pen.10351 ↗
88. Continuous microcellular polystyrene foam extrusion with supercritical CO210.1002/pen.11100 ↗
89. A novel online visualization system for observing polymer extrusion foaming10.1016/j.polymertesting.2016.04.023 ↗
90. Continuous extrusion of nanocellular foam
91. Anisotropy in nanocellular polymers promoted by the addition of needle-like sepiolites10.1002/pi.5813 ↗
92. Nanocellular CO2 foaming of PMMA assisted by block copolymer nanostructuration10.1016/j.cej.2014.01.021 ↗
93. Block copolymers self-assembly allows obtaining tunable micro or nanoporous membranes or depth filters based on PMMA; Fabrication method and nanostructures10.1021/jp409803u ↗
94. SAS copolymer induced nucleation in PS-based open-cell nanocellular polymers
95. Influence of graphene on the cell morphology and mechanical properties of extruded polystyrene foam10.1177/0021955X14566084 ↗
96. Effect of talc content on the volume expansion ratio of extruded PP foams10.1177/0021955X03039247 ↗
97. Nucleation of gas bubbles in extrusion foaming of high-pressure polyethylene10.1007/s11236-005-0129-x ↗
98. Microcellular extrusion foaming of poly(lactide)/poly(butylene adipate-co-terephthalate) blends10.1016/j.msec.2009.10.010 ↗
99. Effects of nano-/micro-sized additives and the corresponding induced crystallinity on the extrusion foaming behavior of PLA using supercritical CO210.1016/j.matdes.2016.03.147 ↗
100. Extrusion of polystyrene nanocomposite foams with supercritical CO 210.1002/pen.10107 ↗