journal article·2021-04

Comparison from Simulated Al0.3Ga0.7As/GaAs/Ge and Al0.3Ga0.7As/GaAs/Si/Ge to Experimental InGaP/GaAs/InGaNAsSb/Ge for Optimized Utilization of the Solar Spectrum

Hongxi Li, Yulin Tian, Ling Shen, Chusheng Liu

Journal of Electronic Materials· Volume 50· Issue 4
Publisher page

Abstract

To make full use of the solar spectrum, the performances of Al0.3Ga0.7As/GaAs/Ge and Al0.3Ga0.7As/GaAs/Si/Ge have been simulated using a one-dimensional device simulator called personal computer oe dimension (PC1D). The dependencies of simulated current density–voltage (J–V) and external quantum efficiency (EQE) results on the thicknesses of each sub-cell have been thoroughly analyzed to determine the preferred thickness. Compared to Al0.3Ga0.7As/GaAs/Ge (1.5/5/50 μm), Al0.3Ga0.7As/GaAs/Si (1.5/5/180 μm) has an increase of 0.36 V for open-circuit voltage (Voc) but a slight decrease of 1.55 mA/cm2 for short-circuit current density (Jsc). Subsequently, a monolithic InGaP/GaAs/InGaNAsSb (1.9/1.42/1 eV, 3 J) cell has been mechanically stacked on a Ge cell with four terminals. The Jsc value of 14 mA/cm2 and 6.5 mA/cm2 is calculated for each sub-cell of 3 J cell and bottom Ge cell with integration of EQE measurements. In addition, the TiO2/SiO2/TiO2 (150 nm/1 µm/150 nm, trilayer) interface provides a thermal conductance (2.9 × 106 W K−1) comparable to the direct bond interface. It is believed that the architecture of InGaP/GaAs/InGaNAsSb on the Ge cell with a trilayer interface between is the preferred choice.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Nanowire Synthesis and Applications · Semiconductor Quantum Structures and Devices · solar cell performance optimization

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (16)

Show source-provided references
1. D.T. Rover, P.A. Basore, and G.M. Thorson, Solar cell modeling on personal computers. IEEE Photovolt. Spec. Conf. 18, 703 (1985).
2. P.A. Basore, D.T. Rover, and A.W. Smith, PC-1D version 2: enhanced numerical solar cell modelling. IEEE Photovolt. Spec. Conf. 18, 389 (1988).
3. P.A. Basore, PC-1D version 3: improved speed and convergence. IEEE Photovolt. Spec. Conf. 16, 299 (1991).
4. P.A. Basore and D.A. Clugston, PC1D version 4 for windows: from analysis to design. IEEE Photovolt. Spec. Conf. 12, 377 (1996).
5. D.A. Clugston and P.A. Basore, PC1D version 5: 32-bit solar cell modeling on personal computers. IEEE Photovolt. Spec. Conf. 16, 207 (1997).
6. X. Cai, X. Zhou, Z. Liu, F. Jiang, and Yu Qingchun, An in-depth analysis of the silicon solar cell key parameters’ optimal magnitudes using PC1D simulations. Optik 164, 105 (2018).10.1016/j.ijleo.2018.02.102 ↗
7. S. Sepeai, S.H. Zaidi, M.K.M. Desa, M.Y. Sulaiman, N.A. Ludin, M.A. Ibrahim, and K. Sopian, Design optimization of bifacial solar cell by PC1D simulation. J. Energy Tech. Policy 3, 5 (2013).
8. M. Belarbi, A. Benyoucef, and B. Benyoucef, Simulation of the solar cells with PC1D, application to cells based on silicon. Adv. Energy Int. J. 1, 1 (2014).
9. A.B. Nawale, R.A. Kalal, A.R. Chavan, T.D. Dongale, and R.K. Kamat, Numerical investigation of spatial effects on the silicon solar cell. J. Nano-Electron. Phys. 8, 02002 (2016).10.21272/jnep.8(2).02002 ↗
10. P. Panek, The influence of the base material parameters on quantum and photoconversion efficiency of the Si solar cells. Arch. Metall. Mater. 61, 1889 (2016).10.1515/amm-2016-0304 ↗
11. S.I. Sato, H. Miyamoto, M. Imaizumi, K. Shimazaki, C. Morioka, K. Kawano, and T. Ohshima, Degradation modeling of InGaP/GaAs/Ge triple-junction solar cells irradiated with various-energy protons. Sol. Energy Mater. Sol. Cells 93, 768 (2009).10.1016/j.solmat.2008.09.044 ↗
12. X. Sheng, C.A. Bower, S. Bonafede, J.W. Wilson, B. Fisher, M. Meitl, H. Yuen, S. Wang, L. Shen, A.R. Banks, C.J. Corcoran, R.G. Nuzzo, S. Burroughs, and J.A. Rogers, Printing-based assembly of quadruple-junction four-terminal microscale solar cells and their use in high-efficiency modules. Nat. Mater. 13, 593 (2014).10.1038/nmat3946 ↗
13. L. Shen, Y. Shen, and F. Li, Optimized utilization of NIR spectrµm with interfacial TiO2/SiO2/TiO2 trilayer in hybrid-integrated multijunction architecture. Sol. Energy Mater. Sol. Cells 160, 425 (2017).10.1016/j.solmat.2016.11.016 ↗
14. L. Shen, H. Li, X. Meng, and F. Li, Transfer printing of fully formed microscale InGaP/GaAs/InGaNAsSb cell on Ge cell in mechanically-stacked quadruple-junction architecture. Sol. Energy 195, 6 (2020).10.1016/j.solener.2019.11.046 ↗
15. A. Carlson, A.M. Bowen, Y. Huang, R.G. Nuzzo, and J.A. Rogers, Transfer printing techniques for materials assembly and micro/nanodevice fabrication. Adv. Mater. 24, 5284 (2012).10.1002/adma.201201386 ↗
16. T. Sumaryada, N.E. Damayanti, S. Rohaeni, H. Syafutra, I.A. Maddu, H. Hardhienata, and H. Alatas, Modeling the thermal response of Al0.3Ga0.7As/GaAs/Ge multijunction solar cells. J. Phys: Conf. Ser. 877, 012030 (2017).