journal article·2025-11Open access

Electromigration in Eutectic Gold-Tin (80Au20Sn-wt%) Solder Joints

Whit Vinson, David Huitink

Journal of Electronic Materials· Volume 54· Issue 11

Abstract

Abstract Eutectic gold-tin solder joints (80Au20Snwt%) with a diameter of 300 μm diameter were subjected to electromigration (EM) conditions of 10,000–20,000 A/cm2 in the ambient temperature range of 125–215 °C. The present work examines a set of 36 experimental test runs using two different test coupons (18 runs with each coupon type and a total of 90 joints tested). Seven of the 36 coupons survived the maximum test duration period of 500 h. One coupon type created a linear electric current pathway through two lengths of 254-μm-diameter copper wire connected by a single gold–tin joint. The other coupon type daisy-chained four gold–tin joints together in series in a flip-chip configuration using two Rogers 4003C printed circuit boards with electroless nickel immersion gold (ENIG)-finished 2-oz (c.56.6-g) copper traces and a 240-μm solder mask defined (SMD) pads. The time to EM failure (TTEF) was recorded for each experimental run, demonstrating reduced lifetime with increasing current density and/or ambient temperature. To account for the Joule heating associated with the high current densities used in this study, temperature coefficient of resistance measurements (TCR) were carried out for both sample groups. To describe the TTEF data, a lifetime model for 80Au20Sn-wt% joints combining the experimental testing conditions with TCR data has been developed. Post-failure analysis (PFA) on the tested solder joints shows several morphological phenomena occurring in the gold–tin joints under EM conditions, including solder migration into the trace, spinodal decomposition, phase coarsening, and phase separation.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Electronic Packaging and Soldering Technologies · Copper Interconnects and Reliability · Electrodeposition and Electroless Coatings

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (42)

Show source-provided references
1. A. D. Kraus and A. Bar-Cohen, Thermal Analysis and Control of Electronic Equipment (McGraw Hill, 1983).
2. D.K. Pradhan, D.C. Moore, A.M. Francis, J. Kupernik, W.J. Kennedy, N.R. Glavin, R.H. Olsson, and D. Jariwala, Materials for high-temperature digital electronics. Nat. Rev. Mater. 9, 790 (2024).10.1038/s41578-024-00731-9 ↗
3. C. Chen, H.M. Tong, and K.N. Tu, Electromigration and thermomigration in Pb-free flip-chip solder joints. Annu. Rev. Mater. Res. (2010). https://doi.org/10.1146/annurev.matsci.38.060407.130253.10.1146/annurev.matsci.38.060407.130253 ↗
4. E.C.C. Yeh, W.J. Choi, K.N. Tu, P. Elenius, and H. Balkan, Current-crowding-induced electromigration failure in flip chip solder joints. Appl. Phys. Lett. (2002). https://doi.org/10.1063/1.1432443.10.1063/1.1432443 ↗
5. W.J. Choi, E.C.C. Yeh, and K.N. Tu, Mean-time-to-failure study of flip chip solder joints on Cu/Ni(V)/Al thin-film under-bump-metallization. J. Appl. Phys. (2003). https://doi.org/10.1063/1.1616993.10.1063/1.1616993 ↗
6. Y. Jiang, H. Li, G. Chen, Y. Mei, and M. Wang, Electromigration behavior of Cu/Sn3.0Ag0.5Cu/Cu ball grid array solder joints. J. Mater. Sci. Mater. Electron. (2019). https://doi.org/10.1007/s10854-019-00925-w.10.1007/s10854-019-00925-w ↗
7. M.N. Bashir, A.S.M.A. Haseeb, A.Z.M.S. Rahman, M.A. Fazal, and C.R. Kao, Reduction of electromigration damage in SAC305 solder joints by adding Ni nanoparticles through flux doping. J. Mater. Sci. 50, 6748 (2015).10.1007/s10853-015-9230-7 ↗
8. Y. Zuo, L. Ma, F. Guo, L. Qiao, Y. Shu, A. Lee, and K.N. Subramanian, Effects of electromigration on the creep and thermal fatigue behavior of Sn58Bi solder joints. J. Electron. Mater. (2014). https://doi.org/10.1007/s11664-014-3345-5.10.1007/s11664-014-3345-5 ↗
9. H. Gan, W.J. Choi, G. Xu, and K.N. Tu, Electromigration in solder joints and solder lines. JOM (2002). https://doi.org/10.1007/BF02701847.10.1007/BF02701847 ↗
10. M. Montazeri, W.M. Vinson, and D.R. Huitink, Accelerated solder interconnect testing under electromigratory and mechanical strain conditions. J. Electron. Packag. (2023). https://doi.org/10.1115/1.4055024.10.1115/1.4055024 ↗
11. W. Vinson, and D. Huitink, Incorporating tensile stress into electromigration life prediction for Cu/SAC305/Cu solder joints. J. Electron. Packag. (2024). https://doi.org/10.1115/1.4066014.10.1115/1.4066014 ↗
12. P.T. Vianco, A.C. Kilgo, and B.M. McKenzie, Gold-tin solder wetting behavior for package lid seals. J. Electron. Packag. (2018). https://doi.org/10.1115/1.4039749.10.1115/1.4039749 ↗
13. Y. Hu, Y. Zhang, Z. Bao, J. Wu, J. Li, J. Wu, and M. Huang, A cu pillar bump bonding method using Au-Sn alloy cap as the interconnection layer. J. Electron. Mater. (2024). https://doi.org/10.1007/s11664-023-10881-1.10.1007/s11664-023-10881-1 ↗
14. Y. S. Bang, J. M. Kim, Y. Kim, J. M. Kim, and Y. K. Kim, Fabrication and Characterization of RF MEMS Package Based on LTCC Lid Substrate and Gold-Tin Eutectic Bonding, in TRANSDUCERS and EUROSENSORS ’07 - 4th International Conference on Solid-State Sensors, Actuators and Microsystems (2007).10.1109/SENSOR.2007.4300583 ↗
15. K. Onodera, T. Ishii, S. Aoyama, and M. Tokumitsu, Controllability of novel Sn/sub 0.95/Au/sub 0.05/ microbumps using interlaminated tin and gold layers for flip-chip interconnection. IEEE Microw. Wirel. Compon. Lett. 13, 256 (2003).10.1109/LMWC.2003.815180 ↗
16. Z.X. Zhu, C.C. Li, L.L. Liao, C.K. Liu, and C.R. Kao, Au-Sn bonding material for the assembly of power integrated circuit module. J. Alloys Compd. (2016). https://doi.org/10.1016/j.jallcom.2016.02.065.10.1016/j.jallcom.2016.02.065 ↗
17. R.R. Chromik, D.N. Wang, A. Shugar, L. Limata, M.R. Notis, and R.P. Vinci, Mechanical properties of intermetallic compounds in the Au-Sn system. J. Mater. Res. (2005). https://doi.org/10.1557/JMR.2005.0269.10.1557/JMR.2005.0269 ↗
18. R.W. Chuang, D. Kim, J. Park, and C.C. Lee, A fluxless process of producing tin-rich gold–tin joints in air. IEEE Trans. Compon. Packag. Technol. (2004). https://doi.org/10.1109/TCAPT.2004.825757.10.1109/TCAPT.2004.825757 ↗
19. C. Pakpum, and K. Kanchiang, Elemental composition optimization to achieve eutectic Au-Sn solder. J. Mater. Sci. Mater. Electron. 35, 1966 (2024).10.1007/s10854-024-13710-1 ↗
20. M. Z. Ding, J. L. Aw, L. S. Lim, L. C. Wai, and V. S. Rao, Direct Eutectic AuSn Solder Bumping on Al Bond Pad Surface Using Laser Solder Ball Jetting, in Proceedings of the 2013 IEEE 15th Electronics Packaging Technology Conference, EPTC 2013 (2013).10.1109/EPTC.2013.6745717 ↗
21. V. Vuorinen, A. Rautiainen, H. Heikkinen, and M. Paulasto-Kröckel, Optimization of contact metallizations for reliable wafer level Au[sbnd]Sn bonds, Microelectronics Reliability 64, (2016).10.1016/j.microrel.2016.07.013 ↗
22. V. Grolier, and R. Schmid-Fetzer, Thermodynamic evaluation of the Au–Sn system. Int. J. Mater. Res. 98, 797 (2007).10.3139/146.101544 ↗
23. A. Debski, W. Gasior, Z. Moser, and R. Major, Enthalpy of formation of intermetallic phases from the Au-Sn system, J. Alloys Compd. 491, (2010).10.1016/j.jallcom.2009.11.003 ↗
24. C. Ruby and D. R. Huitink, Characterization of SAC305 Solder Joints Under Elevated Current, Temperature, and Varying Shear Stress Conditions, in Proceedings of ASME 2023 International Technical Conference and Exhibition on Packaging and Integration of Electronic and Photonic Microsystems, InterPACK 2023 (2023).10.1115/IPACK2023-113756 ↗
25. E.G. Okafor, C. Ruby, M. Norris, A. Leda, and D.R. Huitink, Sequential versus concurrent effects in combined stress solder joint reliability. J. Electron. Packag. (2025). https://doi.org/10.1115/1.4067189.10.1115/1.4067189 ↗
26. George F. Vander Voort, Buehler SumMet - A Guide to Materials Preparation and Analysis, 4th ed. (Lake Bluff, 2018).
27. J.Y. Tsai, C.W. Chang, C.E. Ho, Y.L. Lin, and C.R. Kao, Microstructure evolution of gold–tin eutectic solder on Cu and Ni substrates. J. Electron. Mater. 35, 65 (2006).10.1007/s11664-006-0185-y ↗
28. Low Level Measurements Handbook, 6th ed. (Keithley, n.d.).
29. J.R. Black, Electromigration—a brief survey and some recent results. IEEE Trans. Electron Devices 16, 338 (1969).10.1109/T-ED.1969.16754 ↗
30. Joint Electron Device Engineering Council (JEDEC), Failure Mechanisms and Models for Semiconductor Devices, JEP122H.
31. W. Vinson, and D. Huitink, Mechanical stress state consideration for enhanced electromigration life prediction in aluminum wire bonds. Microelectron. Reliab. 149, 115185 (2023).10.1016/j.microrel.2023.115185 ↗
32. I.A. Blech, and E. Kinsbron, Electromigration in thin gold films on molybdenum surfaces. Thin Solid Films (1975). https://doi.org/10.1016/0040-6090(75)90052-8.10.1016/0040-6090(75)90052-8 ↗
33. T.-H. Chuang, H.-J. Lin, H.-C. Wang, C.-H. Chuang, and C.-H. Tsai, Mechanism of electromigration in Ag-alloy bonding wires with different Pd and Au content. J. Electron. Mater. 44, 623 (2015).10.1007/s11664-014-3558-7 ↗
34. D. W. Kim, J. K. J. Lee, M. J. Lee, S. Y. Pai, S. Chen, and F. Kuo, Evaluation of Electromigration (EM) Life of ENEPIG and CuSOP Surface Finishes with Various Solder Bump Materials, in Proceedings - Electronic Components and Technology Conference (2010).
35. H.Y. Chen, and C. Chen, Measurement of electromigration activation energy in eutectic SnPb and SnAg flip-chip solder joints with Cu and Nl under-bump metallization. J. Mater. Res. (2010). https://doi.org/10.1557/JMR.2010.0230.10.1557/JMR.2010.0230 ↗
36. J. Y. Tsai, C. W. Chang, Y. C. Shieh, Y. C. Hu, and C. R. Kao, Controlling the microstructures from the gold–tin reaction, J. Electron. Mater. 34, (2005).10.1007/s11664-005-0231-1 ↗
37. J. L. Kersey and R. C. Blish, Gold dendrite simulation: Root cause determination, IEEE Trans. Device Mater. Reliab. 4, (2004).10.1109/TDMR.2004.829073 ↗
38. N. Asrar, Detrimental effects of excessive gold plating on lead-free solder joints. J. Fail. Anal. Prev. 10, 50 (2010).10.1007/s11668-009-9305-3 ↗
39. M.W. Beranek, M. Rassaian, C.-H. Tang, C.L.S. John, and V.A. Loebs, Characterization of 63Sn37Pb and 80Au2OSn solder sealed optical fiber feedthroughs subjected to repetitive thermal cycling. IEEE Trans. Adv. Packag. 24, 576 (2001).10.1109/6040.982847 ↗
40. A. Fox, M.E. Davis, P.R. White, T.A. Palumbo, and C.A. Mattoe, The effect of gold–tin intermetallic compound on the low cycle fatigue behavior of copper alloy C72700 and C17200 wires. IEEE Trans. Components Hybrids Manuf. Technol. (1986). https://doi.org/10.1109/TCHMT.1986.1136650.10.1109/TCHMT.1986.1136650 ↗
41. G. Ghosh, Phase stability and cohesive properties of Au-Sn intermetallics: a first-principles study. J. Mater. Res. (2008). https://doi.org/10.1557/JMR.2008.0175.10.1557/JMR.2008.0175 ↗
42. M. AbdelAziz, D.E. Xu, G. Wang, and M. Mayer, Electromigration in solder joints: a cross-sectioned model system for real-time observation. Microelectron. Reliab. 119, 114068 (2021).10.1016/j.microrel.2021.114068 ↗