Electrical and Physicochemical Study of the Metal/p-HgCdTe Interface for MCT-Based Infrared Detectors
Source abstract
Abstract
Abstract Mercury cadmium telluride (MCT) cooled infrared (IR) detectors remain a technological benchmark for the IR community as defined by Rule 7 (J. Electron. Mater. 37:1406). Their performance depends on the ability to resolve small temperature differences between two black bodies, particularly for defense. This thermal resolution is highly sensitive to even slight variations in device quality and is commonly evaluated using residual fixed-pattern noise (RFPN), a second-order performance metric for focal plane array (FPA) characterization. Recent research efforts are focused on developing detectors capable of operating at high operating temperatures (HOT). However, increasing the operating temperature typically leads to a higher number of anomalous pixel responses and elevated dark current and noise, resulting in degradation of detection capabilities. One suspected cause of this degradation is the quality of the metal/ p -type semiconductor interface, particularly due to variations in the Schottky barrier height (SBH). The non-ohmic behavior frequently observed at this interface is commonly attributed to the presence of a Fermi-level pinning effect. This work aims to investigate that hypothesis with a detailed physicochemical analysis of the interface’s formation and composition including a comprehensive correlation with electrical measurements. Metal contacts were fabricated on p -type Hg 0.7 Cd 0.3 Te doped with arsenic, with a doping concentration of approximately 10 18 cm −3 . A consistent surface preparation and deposition method with different metals were applied to form contacts. Electrical properties were characterized using the transfer line method (TLM) at 300 K and 110 K to extract specific contact resistance. To probe the initial surface and buried interface, hard x-ray photoelectron spectroscopy (HAXPES) and time-of-flight secondary ion mass spectrometry (ToF-SIMS) were employed, providing insights into the chemical composition and oxidation phenomena involved in interface state formation. This study highlights the predicted dependence of SBH on the intrinsic nature of metal at 300 K. At low temperature, this dependency is no longer valid due to the predominance of tunneled and trap-assisted conduction. The presence of a buried tellurium oxide layer could explain this deviation, as it may govern the electrical properties of the contact and determine the SBH.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Advanced Semiconductor Detectors and Materials · Advanced Thermoelectric Materials and Devices · Thermography and Photoacoustic Techniques
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (20)
Show source-provided references
1. W. Tennant, D. Lee, M. Zandian, E. Piquette, and M. Carmody, MBE HgCdTe technology: A very general solution to IR detection, described by “Rule 07”, a very convenient heuristic. J. Electron. Mater. 37, 1406 (2008). https://doi.org/10.1007/s11664-008-0426-3.10.1007/s11664-008-0426-3 ↗
2. Y. Reibel, N. Péré-Laperne, L. Rubaldo, T. Augey, G. Decaens, V. Badet, L. Baud, J. Roumegoux, A. Kessler, P. Maillart, N. Ricard, O. Pacaud, and G. Destéfanis, Update on 10 μm pixel pitch MCT-based focal plane array with enhanced functionalities. Infrared Technol. Appl. XLI 9451, 94512E (2015). https://doi.org/10.1117/12.2178954.10.1117/12.2178954 ↗
3. O. Gravrand, J. Rothman, B. Delacourt, F. Boulard, C. Lobre, P. Ballet, JL. Santailler, C. Cervera, D. Brellier, N. Péré-Laperne, V. Destefanis, and A. Kerlain, Shockley–Read–Hall lifetime study and implication in HgCdTe photodiodes for IR detection. J. Electron. Mater. 47, 5680 (2018). https://doi.org/10.1007/s11664-018-6557-2.10.1007/s11664-018-6557-2 ↗
4. VS. Meena and MS. Mehata, Thermally grown indium (In) thin-film for creating ohmic contact and In-bumps for HgCdTe-based IR detectors. Appl. Surf. Sci. 596, 153501 (2022). https://doi.org/10.1016/j.apsusc.2022.153501.10.1016/j.apsusc.2022.153501 ↗
5. GP. Carey, AK. Wahi, DJ. Friedman, I.Lindau, and WE. Spicer, Fundamental and practical studies of metal contacts on mercury zinc telluride (Stanford Electronics Labs, Stanford University).
6. EC. Piquette, The effect of contact resistance on short wavelength infrared focal plane array noise. J. Electron. Mater. 53, 5858 (2024). https://doi.org/10.1007/s11664-024-11296-2.10.1007/s11664-024-11296-2 ↗
7. AM. Cowley and SM. Sze, Surface states and barrier height of metal–semiconductor systems. J. Appl. Phys. 36, 3212 (1965). https://doi.org/10.1063/1.1702952.10.1063/1.1702952 ↗
8. DK. Schroder, Semiconductor Material and Device Characterization, 3rd edn. (Wiley–IEEE Press, Hoboken, NJ, 2006)10.1002/0471749095 ↗
9. L. Mollard, G. Bourgeois, C. Lobre, S. Gout, S. Viollet-Bosson, N. Baier, G. Destefanis, O. Gravrand, JP. Barnes, F. Milesi, A. Kerlain, L. Rubaldo, and A. Manissadjian, p-on-n HgCdTe infrared focal-plane arrays: From short-wave to very-long-wave infrared. J. Electron. Mater. 43, 802 (2014). https://doi.org/10.1007/s11664-013-2809-3.10.1007/s11664-013-2809-3 ↗
10. S. Tanuma, CJ. Powell, and DR. Penn, Calculations of electron inelastic mean free path V Data for 14 organic compounds over the 50-2000 eV range. Surf. Interface Anal. 21, 165 (1994).10.1002/sia.740210302 ↗
11. JA. Bearden, and AF. Burr, Reevaluation of x-ray atomic energy levels. Rev. Mod. Phys. 39, 125 (1967).10.1103/RevModPhys.39.125 ↗
12. SM. Sze, Y. Li, and KK. Ng, Physics of Semiconductor Devices, 4th ed., (Hoboken, NJ: Wiley, 2021).
13. FA. Padovani and R. Stratton, Field and thermionic field emission in Schottky barriers. Solid-State Electron. 9, 695 (1966). https://doi.org/10.1016/0038-1101(66)90097-9.10.1016/0038-1101(66)90097-9 ↗
14. A. Rogalski, K. Adamiec, and J. Rutkowski, Narrow-Gap Semiconductor Photodiodes (Bellingham, WA: SPIE, 2000).10.1117/3.2536930 ↗
15. R. Dornhaus, G. Nimtz, and B. Schlicht, Narrow-Gap Semiconductors (Berlin: Springer, 1983).10.1007/BFb0044919 ↗
16. F. Sizov, Z. Tsybrii, M. Apats’ka, N. Dmytruk, V. Slipokurov, S. Bunchuk, Y. Bezsmolnyy, V. Popovych, M. Wiertel, and N. Mikhailov, Ohmic metal/Hg1−xCdxTe (x ≈ 0.3) contacts. Semicond. Sci. Technol. 35, 125030 (2020).10.1088/1361-6641/abc0f7 ↗
17. DR. Rhiger and RE. Kvaas, Composition of native oxides and etched surfaces on Hg₁−xCdxTe. J. Vac. Sci. Technol. 21, 168 (1982). https://doi.org/10.1116/1.571705.10.1116/1.571705 ↗
18. S. Bel, C. Lobre, S. Petit, M. Veillerot, and G. Badano, Characterization of intentional contaminations at the HgCdTe passivation interface and their effects on photodiode performance. J. Electron. Mater. 53, 5820 (2024). https://doi.org/10.1007/s11664-024-11137-2.10.1007/s11664-024-11137-2 ↗
19. X. Zhang, H. Takeuchi, D. Connelly, M. Hytha, RJ. Mears, LM. Rubin, and TJK. Liu, Tuning of Schottky barrier height using oxygen-inserted (OI) layers and fluorine implantation. AIP Adv. 10, 065310 (2020). https://doi.org/10.1063/1.5144507.10.1063/1.5144507 ↗
20. A. Singh, AK. Shukla, S. Jain, BS. Yadav, and R. Pal, Electrical characteristics of electroless gold contacts on p-type Hg₁−xCdxTe. Mater. Sci. Semicond. Process. 26, 294 (2014). https://doi.org/10.1016/j.mssp.2014.04.039.10.1016/j.mssp.2014.04.039 ↗