journal article·2012-04-01

A Microstructure and Microhardness Characterization of a Friction Plug Weld in Friction Stir Welded 2195 Al-Li

D. F. Metz, E. R. Weishaupt, M. E. Barkey, B. S. Fairbee

Publisher page

Abstract

In this study, extruded 2195-T8 plugs that were friction welded into the friction stir weld of 2195-T8 base metal plates were examined. This study characterizes the resulting microstructure and microhardness of the plug weld interfaces with the friction stir welded material and base metal in an effort to identify the extent of the thermal, thermomechanical, and mechanical effects introduced by the friction plug welding process. A zone of recrystallized material was observed around the plug weld circumference. The thickness of the recrystallized layer was measured to be 30–122 μm. The hardness measured near the plug weld interface was found to be 110–130 HK100g, or approximately 35% less than the base metal hardness. By characterizing the hardness of these zones, insight can be gathered into the transformation of material from the friction plug welding process around the fusion zone, and areas that may control the fatigue behavior of the joint.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Advanced Welding Techniques Analysis · Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Aerospace Engineering and Mechanics Department,The University of Alabama, Tuscaloosa, AL 35487

Professor Mem. ASME

References (21)

Show source-provided references
1. Hartley, P. J. , 2000, “Friction Plug Weld Repair for the Space Shuttle External Tank,” NASA Document ID 20000093962, Johnson Space Center, Marshall Space Flight Center.
2. Fatigue of Friction Stir Welds in Aluminum Alloys that Contain Root Flaws10.1016/S0142-1123(03)00060-4 ↗
3. Khaled, T. , 2005, “An Outsider Looks at Friction Stir Welding,” Federal Aviation Administration Report No. ANM-112N-05-06, pp. 14–15.
4. Wells, D. , 2008, private communication.
5. Colleta, E. R., and Cantrell, M. A., 2001, “Friction Pull Plug Welding: Top Hat Plug Design,” U.S. Patent No. US 6,253,987 B1.
6. Colleta, E. R., and Cantrell, M. A., 2002, “Friction Pull Plug Welding: Chamfered Heat Sink Pull Plug Design,” U.S. Patent No. US 6,460,750 B1.
7. Li, Z. X., Cantrell, M. A., and Brown, R. J., 2000, “Process Development and Microstructural Characterization on Friction Plug Welded 2195 and 2219 Alloys,” AeroMat 2000.
8. The Effects of Artificial Aging on the Microstructure and Fracture Toughness of Al-Cu-Li Alloy 219510.1361/105994998770347576 ↗
9. Microstructural Characterization and Stress Corrosion Evaluation of Friction Stir Welded Al 2195 and Al 2219 Alloys
10. Effects of Welding and Weld Heat-Affected Zone Simulation on the Microstructure and Mechanical Behavior of a 2195 Aluminum-Lithium Alloy10.1007/s11661-001-1025-6 ↗
11. Near-Threshold Fatigue Crack Growth Behavior of 2195 Aluminum Lithium Alloy Prediction of Crack Propagation Direction and Influence of Stress Ratio10.1007/s11661-000-0164-5 ↗
12. Microtexture, Microstructure and Plastic Anisotropy of AA2195
13. TEM Study of the FSW Nugget in AA2195-T8110.1007/s10853-005-2808-8 ↗
14. Study of Microstructural Evolution in Friction-Stir Welded Thin-Sheet Al-Cu-Li Alloy using Transmission-Electron Microscopy10.1016/j.scriptamat.2006.11.028 ↗
15. Subramanian, P., Nirmalan, N., Young, L., Sudkamp, P., Mika, D., Larsen, M., Othon, M., Dupree, P., Walker, S., and Catlin, G., 2003, “Fundamental Studies of Microstructure Evolution during Stir Welding of Aluminum Alloys,” NASA Technical Report No. 20031028177.
16. Precipitation and Grain Refinement in a 2195 Al Friction Stir Weld10.1007/s11661-006-1054-2 ↗
17. Development of Grain Structure During Friction Stir Welding10.1016/j.scriptamat.2004.04.017 ↗
18. Wang, Z. M., and Shenoy, R. N., 1998, “Microstructural Characterization of Aluminum-Lithium Alloys 1460 and 2195,” NASA CR-1998-206914.
19. Coletta, E. R., and Cantrell, M. A., 2000, “Friction Plug Weld Repair Geometric Innovations,” Marshall Space Flight Center, NASA Document ID: 20000112928.
20. ASTM E3, “Standard Guide for Preparation of Metallographic Specimens Annual Book of ASTM Standards,” American Society for Testing and Materials, Volume 3.01.
21. Colleta, E. R., and Cantrell, M. A., 2005, “Friction Pull Plug Welding: Chamfered Heat Sink Pull Plug Design,” U.S. Patent No. US 6,880,743 B1.