The Effect of Cold Expansion on the Fatigue Life of the Chamfered Holes
Source abstract
Abstract
The cold expansion method is one of the most popular techniques in the fatigue enhancement processes, and it has been widely used as a means of improving the fatigue resistance for aircraft structures with holes. Cold expanded holes have lower compressive residual stresses on the entry surface rather than the middle and exit surfaces. Due to the nonuniform residual stress distribution, fatigue crack initiation often occurs on the entry surface. This study proposes a new approach to increase the compressive residual stress magnitude at the entry of the hole. The new method is to apply chamfers into holes before the cold expansion process. Split mandrel process was used to cold work the hole with and without chamfers. Both numerical and experimental studies were done to verify the effects of hole chamfers on the residual stress distribution of the cold expanded holes. Finite element analysis (FEA) was conducted in order to see the effects of the chamfer geometries on the residual stress distributions. The FEA results showed an improvement of compressive residual stress magnitudes at the entry position of the cold expanded hole. The numerical results were compared with X-ray diffraction measurements. Fatigue tests were done to compare the fatigue life of the holes with various chamfer sizes and angles. The cold expansion chamfered holes showed a clear improvement in fatigue life over cold expanded holes without chamfers.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Surface Treatment and Residual Stress · Fatigue and fracture mechanics · Erosion and Abrasive Machining
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
School of Engineering and Computer Science, Washington State University, Vancouver, WA 98686
Computer Aided Mechanical Design, Induk Institute of technology, Seoul 139-749, Korea
References (22)
Show source-provided references
1. Residual Stress Effect on Fatigue Striation Spacing in a Cold-Worked Rivet Hole10.1016/j.tafmec.2004.08.003 ↗
2. Experimental and Analytical Studies of Residual Stress Field Evaluation and Fatigue Cracks at Cold Expansion Holes
3. A Finite Element Simulation of the Cold Working Process for Fastener Holes10.1243/0309324971513418 ↗
4. Experimental Investigation on the Effects of Cold Expansion of Fastener Holes10.1046/j.1460-2695.1998.00430.x ↗
5. Relaxation of Residual Stresses at Cold-Worked Fastener Holes Due to Fatigue Loading10.1111/j.1460-2695.1997.tb01501.x ↗
6. Three-Dimensional Finite Element Analysis of Cold Expansion of Adjacent Holes10.1016/S0020-7403(98)00007-1 ↗
7. A Novel Method of Cold Expansion Which Creates Near-Uniform Compressive Tangential Residual Stress Around a Fastener Hole10.1111/j.1460-2695.2004.00727.x ↗
8. Finite Element Analysis of the Residual Stress by Cold Expansion Method Under the Influence of Adjacent Holes
9. Finite Element Analysis of the Stress Intensity Factor and the Residual Stress by Cold Expansion Method in CT Specimen
10. Fatigue Life Estimation After Crack Repair in 6005 A-T6 Aluminum Alloy Using the Cold Expansion Hole Technique10.1046/j.1460-2695.2000.00356.x ↗
11. Three-Dimensional Stress Distribution Around Cold Expanded Holes in Aluminum Alloys10.1016/0013-7944(94)90189-9 ↗
12. Prediction of the Growth Rate for Fatigue Cracks Emanating From Cold Expanded Holes10.1016/j.ijfatigue.2003.10.015 ↗
13. Rich, D. L., and Impellizzeri, L. F., 1977, “Fatigue Analysis of Cold-Worked and Interference Fit Fastener Holes,” Report No. ASTM STP 637, pp. 153–175.10.1520/STP27993S ↗
14. Three Dimensional Finite Element Analysis of the Fastener Holes in Two Aluminum Alloys10.1115/1.1448922 ↗
15. Cold Expansion Effect on the Initiation and the Propagation of the Fatigue Crack10.1016/S0142-1123(03)00127-0 ↗
16. Residual Stresses Around an Expanded Hole in an Aluminum Clad Sheet
17. Analysis of Residual Stresses Induced by Cold Expansion Using Finite Element Method
18. A Literature Survey on the Stability and Significance of Residual Stresses During Fatigue10.1111/j.1460-2695.2007.01102.x ↗
19. 2003, ABAQUS, Version 6-4-1, User’s Manual, Abaqus, Inc., RI.
20. ASTM International, 1982, “Standard Practice for Conducting Constant Amplitude Axial Fatigue Tests of Metallic Materials,” Report No. ASTM E 466-82, pp. 543–547.
21. ASTM International, 2002, “Standard Test Method for Verifying the Alignment of X-Ray Diffraction Instrumentation for Residual Stress Measurement,” Report No. ASTM E915-96.
22. ASTM International, 1993, “Standard Test Method for Measurement of Fatigue Crack Growth Rates,” Report No. ASTM E 647-93, pp. 679–706.